纳米氧化物颗粒对水基钻井液润滑性能影响的试验研究

通过在水基钻井液中添加纳米氧化物颗粒,来改善其润滑性能。选用了Al2O3、TiO2及SiO2三种纳米氧化物颗粒作为钻井液改性添加剂,利用极压润滑仪及销盘摩擦磨损实验仪研究了添加不同种类和浓度纳米颗粒氧化物对水基钻井液的润滑性能及减摩效果的影响。结果表明,所添加的3种球形纳米颗粒均有润滑减阻减摩的效果,其中SiO2颗粒的钻井液的润滑性能、滤失性能以及减摩效果都是最好的。当纳米SiO2颗粒加量为0.4%时,滤失量最小,润滑系数降低率达到15.6%,摩擦系数降低率为32.0%,磨痕轨迹平滑,减摩效果最为明显。当纳米颗粒浓度超过0.5%时,减摩效果降低,磨盘脱层磨损明显。     

低固相冲洗液在赣南再里地区的应用研究

钻进过程中,孔壁的稳定性和冲洗液的渗漏是影响钻进效率和钻孔质量的重要因素。孔内情况越复杂,施工周期越长,对冲洗液性能的要求也越高。赣南再里地区施工区构造发育复杂,地层中存在大量的松散、胶结性差的砂岩以及高岭土、绿泥石等水敏性地层,钻探施工钻孔容易缩径,孔壁稳定性差,极易出现剥落、掉块、坍塌等现象,试验采用了低固相不分散冲洗液,取得了良好的钻进效果。     

Pressure characteristics of bubble collapse near a rigid wall in compressible fluid

High speed liquid jet and shockwave can be produced when a bubble collapses near a rigid wall, which may cause severe damage to solid structures. A hybrid algorithm was adopted to simulate bubble motion and associated pressures near a wall combining Level Set-Modified Ghost Fluid-Discontinuous Galerkin (LS-MGF-DG) method and boundary element method (BEM). Numerical results were compared with experimental data to validate the presented algorithm. Jet formation was simulated by BEM and the induced pressure on the wall was calculated with auxiliary function. The pressure at the point on the wall where the jet points to reaches its peak value after the jet penetrates the bubble. Bubble collapse and rebounding were simulated by the LS-MGF-DG method. Shock-wave is induced when the bubble collapse toroidally to a minimum volume and the pressure at wall center reaches the maximum due to shockwave superposition. A third pressure peak is found associated with the bubble rebounds and bubble splitting. In the case studied, a higher pressure was found due to collapse shockwave than bubble jet and affects a larger area of the wall. In addition, the three pressure peaks due to jet impact, collapse impact as well as bubble rebounding and splitting decrease with the increase of the standoff distance.     

Investigation of a longfin inshore squid's swimming characteristics and an underwater locomotion during acceleration

In the present study, locomotion of a real longfin inshore squid (Doryteuthis pealeii) was numerically investigated. Geometry of a real squid was obtained using computed tomography (CT) images. In addition to a two-dimensional axisymmetric squid model, a modified squid model with no cavities around her head and an ellipse shaped model were generated with a fineness ratio (the ratio of body length to maximum body diameter) of 7.56. These numerical models were exposed to an acceleration with two different velocity programs. Added mass and basset forces on bodies were calculated during acceleration of the squid models starting from rest. Pressure and viscous drag forces were also calculated due to pressure variation along the squid models and friction on the surface of the models. The effect of a nozzle diameter on jet velocities and propulsive efficiency at all bodies were evaluated when time dependent velocity profiles (from 0 to 10 m/s in 0.5 and 1 s time durations) were set for the inlet of computational domain. The modified squid model required least thrust force during acceleration phase of time dependent velocity profile compared to the other models while the 0.02 m nozzle diameter provided largest propulsive efficiency for all models.     

Hydrothermal Fluid Sources of the Fengjia Barite–fluorite Deposit in Southeast Sichuan,China: Evidence from Fluid Inclusions and Hydrogen and Oxygen Isotopes

The Fengjia barite–fluorite deposit in southeast Sichuan is a stratabound ore deposit which occurs mainly in Lower Ordovician carbonate rocks. Here we present results from fluid inclusion and oxygen and hydrogen isotope studies to determine the nature and origin of the hydrothermal fluids that generated the deposit. The temperature of the ore‐forming fluid shows a range of 86 to 302 °C. Our detailed microthermometric data show that the temperature during mineralization of the fluorite and barite in the early ore‐forming stage was higher than that during the formation of the calcite in the late ore‐forming stage. The salinity varied substantially from 0.18% to 21.19% NaCl eqv., whereas the density was around 1.00 g/cm³. The fluid composition was mainly H₂O (>91.33%), followed by CO₂, CH₄ and traces of C₂H₆, CO, Ar, and H₂S. The dominant cation was Na⁺ and the dominant anion Cl^‐, followed by Ca²⁺, SO₄^2‐, K⁺, and Mg²⁺, indicating a mid–low‐temperature, mid‐low‐salinity, low‐density NaCl–H₂O system. Our results demonstrate that the temperature decreased during the ore‐forming process and the fluid system changed from a closed reducing environment to an open oxidizing environment. The hydrogen and oxygen isotope data demonstrate that the hydrothermal fluids in the study area had multiple sources, primarily formation water, as well as meteoric water and metamorphic water. Combined with the geological setting and mineralization features we infer that the stratabound barite–fluorite deposits originated from mid–low‐temperature hydrothermal fluids and formed vein filling in the fault zone.     

Tectono–Thermal Evolution, Hydrocarbon Filling and Accumulation Phases of the Hari Sag, in the Yingen–Ejinaqi Basin, Inner Mongolia, Northern China

This work restored the erosion thickness of the top surface of each Cretaceous formations penetrated by the typical well in the Hari sag, and simulated the subsidence burial history of this well with software BasinMod. It is firstly pointed out that the tectonic subsidence evolution of the Hari sag since the Cretaceous can be divided into four phases: initial subsidence phase, rapid subsidence phase,uplift and erosion phase, and stable slow subsidence phase. A detailed reconstruction of the tectonothermal evolution and hydrocarbon generation histories of typical well was undertaken using the EASY R_0% model, which is constrained by vitrinite reflectance(R_0) and homogenization temperatures of fluid inclusions. In the rapid subsidence phase, the peak period of hydrocarbon generation was reached at c.a.105.59 Ma with the increasing thermal evolution degree. A concomitant rapid increase in paleotemperatures occurred and reached a maximum geothermal gradient of about 43-45℃/km. The main hydrocarbon generation period ensued around 105.59-80.00 Ma and the greatest buried depth of the Hari sag was reached at c.a. 80.00 Ma, when the maximum paleo-temperature was over 180℃.Subsequently, the sag entered an uplift and erosion phase followed by a stable slow subsidence phase during which the temperature gradient, thermal evolution, and hydrocarbon generation decreased gradually. The hydrocarbon accumulation period was discussed based on homogenization temperatures of inclusions and it is believed that two periods of rapid hydrocarbon accumulation events occurred during the Cretaceous rapid subsidence phase. The first accumulation period observed in the Bayingebi Formation(K_1 b) occurred primarily around 105.59-103.50 Ma with temperatures of 125-150℃. The second accumulation period observed in the Suhongtu Formation(K_1 s) occurred primarily around84.00-80.00 Ma with temperatures of 120-130℃. The second is the major accumulation period, and the accumulation mainly occurred in the Late Cretaceous. The hydrocarbon accumulation process was comprehensively controlled by tectono-thermal evolution and hydrocarbon generation history. During the rapid subsidence phase, the paleo temperature and geothermal gradient increased rapidly and resulted in increasing thermal evolution extending into the peak period of hydrocarbon generation,which is the key reason for hydrocarbon filling and accumulation.     

Ore-forming Fluid and Mineral Source of the Hongshi Copper Deposit in the Kalatage Area, East Tianshan, Xinjiang, NW China

The Hongshi copper deposit is located in the middle of the Kalatage ore district in the northern segment of the Dananhu-Tousuquan island-arc belt in East Tianshan, Xinjiang, NW China. This study analyses the fluid inclusions and H, O, and S stable isotopic compositions of the deposit. The fluid-inclusion data indicate that aqueous fluid inclusions were trapped in chalcopyrite-bearing quartz veins in the gangue minerals. The homogenization temperatures range from 108°C to 299°C, and the salinities range from 0.5% to 11.8%, indicating medium to low temperatures and salinities. The trapping pressures range from 34.5 MPa to 56.8 MPa. The δ18OH2O values and δD values of the fluid range from ?6.94‰ to ?5.33‰ and from ?95.31‰ to ?48.20‰, respectively. The H and O isotopic data indicate that the ore-forming fluid derived from a mix of magmatic water and meteoric water and that meteoric water played a significant role. The S isotopic composition of pyrite ranges from 1.9‰ to 5.2‰, with an average value of 3.1‰, and the S isotopic composition of chalcopyrite ranges from ?0.9‰ to 4‰, with an average value of 1.36‰, implying that the S in the ore-forming materials was derived from the mantle. The introduction of meteoric water decreased the temperature, volatile content, and pressure, resulting in immiscibility. These factors may have been the major causes of the mineralization of the Hongshi copper deposit. Based on all the geologic and fluid characteristics, we conclude that the Hongshi copper deposit is an epithermal deposit.     

四川平武银厂金矿勘探复杂地层钻进技术

四川平武银厂金矿区钻探施工中遇到漏失、缩径、岩心破碎、易孔斜和钻孔事故频发等施工难题,施工难度极大。本文结合地层特点,通过采用绳索取心液动锤、高密度低失水泥浆体系、跟管钻进等工艺技术措施,提高了钻进效率和施工质量,大幅度减少了孔内事故的发生,为顺利完成钻孔施工任务奠定了坚实的基础。     

塔里木陆块西北缘萨热克砂岩型铜矿床构造-流体演化对成矿的制约

塔里木陆块西北缘萨热克砂岩型铜矿床构造演化、流体演化与成矿之间具有密切关系,处于一个统一系统中。矿床成岩期方解石中包裹体水的δD值为-65.3‰~-99.2‰,改造成矿期石英包裹体水的δD值为-77.7‰~-96.3‰,成岩成矿期成矿流体δ~(18)OH_2O变化范围为-3.22‰~1.84‰,改造成矿期成矿流体δ~(18)OH_2O变化范围为-4.26‰~5.14‰,指示萨热克铜矿成岩期、改造期成矿流体主要为中生代大气降水及其经水岩作用而成的盆地卤水。矿石中辉铜矿δ~(34)S值为-24.7‰~-15.4‰,指示硫主要源自硫酸盐细菌与有机质还原,部分源于有机硫。构造与成矿流体演化对砂岩铜矿成矿起关键制约作用。盆地发展早期强烈的抬升运动使盆地周缘基底与古生界剥蚀,为富铜矿源层的形成提供了丰富物源,至晚侏罗世盆地发展晚期,长期演化积聚的巨量含矿流体在库孜贡苏组砾岩胶结物及裂隙中富集,在萨热克巴依盆地内形成具有经济意义的砂岩型铜矿床。     

Occurrence and Chemical Compositions of Amphiboles in Altered Dioritic Rocks of Laiwu Skarn‐Type Iron Deposit in West Shandong Area,China

The Laiwu Fe deposit is the largest skarn‐type deposit in West Shandong in China, with an estimated reserve of 290 Mt of iron ore. Here, we investigate the occurrence and chemical composition of amphiboles in altered dioritic rocks of this deposit. Three generations of amphibole group minerals were identified in these rocks. The first type (Type 1) is a hornblende with a generally euhedral crystal shape, 150–500 μm in size, and dominantly occurs in the host monzonite. The second type (Type 2) of hornblende occurs as fine grains (<100 μm) or concentric rims, less than 50 μm in thickness, around the Type 1 hornblende. The third type (Type 3) of amphibole is anhedral actinolite occurring along the boundary or the cracks of the Type 1 or 2 hornblende grains. The Type 1 hornblende has higher FeO (12.5–15.6 wt.%) and lower MgO contents (11.2–14.6 wt.%) than the Type 2 hornblende, which has an FeO content ranging from 8.8 to 10.5 wt.% and MgO content ranging from 14.2 to 17.1 wt.%. The Type 3 actinolite shows the lowest FeO (4.6–6.4 wt.%) and highest MgO (19.8–21.2 wt.%) contents. We infer that the Type 2 hornblende formed from Fe‐rich hydrothermal fluids released during rapid upwelling of the crystallizing magma. The fluids were relatively reduced and enriched in Fe. The Type 3 actinolite formed by coupled dissolution and reprecipitation, and its formation is one of the features denoting Fe‐enrichment events. Our study of these types of amphibole provides insights into the ore formation process.