岩体三维节点偶对分析及其应用

本文讨论了节点偶对分析的三维扩展。节点偶对分析是针对摩擦滑动节理单元的约束边界进行的序列矢量判定。在三维节理单元的分析中,几何约束和相应的力学判据极为复杂,采用节点偶对等效结合力方法才能迎刃而解。文中对三维转向节理模型的分析得到合理的结果,它表明本文所提出的方法可成功地应用于节理岩体的有限元分析。     

Alluvial architecture of the Holocene Rhine–Meuse delta (the Netherlands)

Ancient fluvial successions often act as hydrocarbon reservoirs. Sub‐surface data on the alluvial architecture of fluvial successions are often incomplete and modelling is performed to reconstruct the stratigraphy. However, all alluvial architecture models suffer from the scarcity of field data to test and calibrate them. The purposes of this study were to quantify the alluvial architecture of the Holocene Rhine–Meuse delta (the Netherlands) and to determine spatio‐temporal trends in the architecture. Five north–south orientated cross‐sections, perpendicular to the general flow direction, were compiled for the fluvial‐dominated part of the delta. These sections were used to calculate the width/thickness ratios of fluvial sandbodies (SBW/SBT) and the proportions of channel‐belt deposits (CDP), clastic overbank deposits (ODP) and organic material (OP) in the succession. Furthermore, the connectedness ratio (CR) between channel belts was calculated for each cross‐section. Distinct spatial and temporal trends in the alluvial architecture were found. SBW/SBT ratios decrease by a factor of ca 4 in a downstream direction. CDP decreases from ca 0·7 (upstream) to ca 0·3 (downstream). OP increases from less than 0·05 in the upstream part of the delta to more than 0·25 in the downstream delta. ODP is approximately constant (0·4). CR is ca 0·25 upstream, which is approximately two times larger than in the downstream part of the delta. Furthermore, CDP in the downstream Rhine–Meuse delta increases after 3000 cal yr BP. These trends are attributed to variations in available accommodation space, floodplain geometry and channel‐belt size. For instance, channel belts tend to narrow in a downstream direction, which reduces SBW/SBT, CDP and CR. Tectonics cause local deviations in the general architectural trends. In addition, the positive correlation between avulsion frequency and the ratio of local to regional aggradation rate probably influenced alluvial architecture in the Rhine–Meuse delta. The Rhine–Meuse data set can be a great resource when developing more sophisticated models for alluvial architecture simulation, which eventually could lead to better characterizations of hydrocarbon reservoirs. To aid such usage of the Rhine–Meuse data set, constraints for relevant parameters are provided at the end of the paper.     

Carbonate aeolianites of western Saurashtra,India: experimental decipherment of the depositional mechanisms

Granular carbonate deposits of Late Pleistocene to Early Holocene age, commonly referred to as ‘miliolite limestone’, occur in a linear belt, parallel to the southern coast of Saurashtra, India. In the present study area these carbonate deposits are found in select valleys between ridges and mounds of pyroclastic material present in the Deccan trap plateau. Two different depositional histories have been proposed for these sediments. The presence of marine bioclasts led to the postulation of a marine origin for these deposits. The second school of thought propounded redeposition of the coastal sediments by aeolian processes. Although a few features could not be explained by the proposed aeolian model, critical comparison of these two views favoured the aeolian origin. The mode of occurrence, lithological and structural attributes, and microscopic evidence presented here, also support a possible aeolian origin for these deposits. Experimental observation indicates that these carbonate aeolianites represent backflow deposits, which accumulated because of the flow separation caused by the presence of topographic highs. The conspicuous concave‐up geometry of the deposit conformed to the shape of the separation bulb. In view of the inferred depositional mechanism, the disposition of the deposits and the signature of the palaeoflow direction suggest that the carbonate particles were derived from the north‐western coast of Saurashtra by strong south‐easterly winds. Massive granular carbonates with outsized basement clasts appear to be the product of avalanching of granular material from the higher contours because of oversteepening of the primary deposit.     

Mapping Proterozoic unconformity-related uranium deposits in the Rockhole area, Northern Territory, Australia using landsat ETM+

The Rockhole area, Northern Territory, Australia, hosts a number of Proterozoic unconformity-related uranium deposits. The geology of the area features within Paleoproterozoic rocks of the Pine Creek Orogen, near the unconformity with overlying platform cover sandstone of the Paleo- to Mesoproterozoic McArthur Basin. Landsat Enhanced Thematic Mapper plus (ETM+) data was used in the Rockhole area to assist in mapping geological structures and lithology, and to identify anomalous concentrations of ferrous minerals, the product of alteration, which can be indicators of buried uranium mineralization. Several image-processing procedures were applied to the ETM+ data to identify, isolate and enhance mineralogical information as simple and complex false color composites. ETM+ 754 shown as red green and blue respectively was the best simple image. Overall, complex images based on Principal Component Analysis proved to be the most useful products. Sandstone, shale and siltstone, the target lithologies, Koolpin Formation, the target stratigraphic unit, and bleaching pattern due to the removal of iron(II) compounds, the target alteration pattern, were confidently mapped to provide information required by the mineral emplacement model, which ultimately identified areas of likely uranium mineralization. Thus the contrasting behavior of the two principle oxidation states of uranium and iron can be utilized to map/delineate bleached alteration zones associated with economic concentrations of uranium using multispectral sensors like Landsat or better hyperspectral sensors.     

The geochemistry of gem opals as evidence of their origin

Seventy-seven gem opals from ten countries were analyzed by inductively coupled plasma-mass spectrometry (ICP-MS) through a dilution process, in order to establish the nature of the impurities. The results are correlated to the mode of formation and physical properties and are instrumental in establishing the geographical origin of a gem opal. The geochemistry of an opal is shown to be dependant mostly on the host rock, at least for examples from Mexico and Brazil, even if modified by weathering processes. In order of decreasing concentration, the main impurities present are Al, Ca, Fe, K, Na, and Mg (more than 500 ppm). Other noticeable elements in lesser amounts are Ba, followed by Zr, Sr, Rb, U, and Pb. For the first time, geochemistry helps to discriminate some varieties of opals. The Ba content, as well as the chondrite-normalized REE pattern, are the keys to separating sedimentary opals (Ba > 110 ppm, Eu and Ce anomalies) from volcanic opals (Ba < 110 ppm, no Eu or Ce anomaly). The Ca content, and to a lesser extent that of Mg, Al, K and Nb, helps to distinguish gem opals from different volcanic environments. The limited range of concentrations for all elements in precious (play-of-color) compared to common opals, indicates that this variety must have very specific, or more restricted, conditions of formation. We tentatively interpreted the presence of impurities in terms of crystallochemistry, even if opal is a poorly crystallized or amorphous material. The main replacement is the substitution of Si⁴⁺ by Al³⁺ and Fe³⁺. The induced charge imbalance is compensated chiefly by Ca²⁺, Mg²⁺, Mn²⁺, Ba²⁺, K⁺, and Na⁺. In terms of origin of color, greater concentrations of iron induce darker colors (from yellow to “chocolate brown”). This element inhibits luminescence for concentrations above 1000 ppm, whereas already a low content in U (≤ 1 ppm) induces a green luminescence.     

等离子体质谱法测定玄武岩中微量元素三种样品预处理方法的比较

在测定玄武岩的微量元素时,为了保证得到的微量元素结果反映源区特征,需经预处理去除玄武岩的孔洞中充填的碳酸盐等物质。选取雷州半岛新生代玄武岩三个样品,每一个样品用三种预处理方法进行预处理,等离子体质谱法测定其中的微量元素。分析结果表明,用稀硝酸浸泡样品,会导致玄武岩中大多数微量元素严重丢失,得到的数据失真;而用稀盐酸浸泡去除碳酸盐的方法基本不改变玄武岩中微量元素的含量。     

内蒙古正蓝旗羊蹄子山-磨石山钛矿区硅质岩地球化学特征及沉积环境意义

文章通过详细的野外地质调查和系统的岩石化学、稀土元素、微量元素及硅、氧同位素等研究,探讨了羊蹄子山-磨石山钛矿区无矿白色硅质岩和富钛硅质岩的成因及形成地质构造环境。研究结果表明,呈厚层状产出的无矿白色硅质岩具较高的SiO2、Al2O3含量及Al/(Al Fe Mn)、Al2O3/(Al2O3 Fe2O3)比值,稀土元素总量很低,其北美页岩标准化配分模式为向右倾的曲线,无明显铈异常和铕异常,表明其形成于受陆源影响的大陆边缘构造环境;赋矿岩系中薄层状富钛硅质岩的TiO2、Fe2O3、Cu、V含量较高,但Al/(Al Fe Mn)、Al2O3/(Al2O3 Fe2O3)比值较低,稀土元素总量较高,北美页岩标准化曲线为明显左倾型-平坦型,具弱的负铈异常,表明其形成于洋脊及附近环境。两种硅质岩的δ30Si值为变化较小的负值,与热水沉积和某些生物成因硅质岩的硅同位素组成相似,两者的δ18O值范围和平均值均相似。两类硅质岩的成因及形成构造环境不同,富钛硅质岩的地球化学特征表明,该矿床的形成与本区元古宙海底火山热液喷流作用有关。     

内蒙古敖包吐萤石矿床的Sr、Nd、Pb同位素地球化学特征

敖包吐萤石矿床是内蒙古北部苏莫查干地区单一萤石矿集区中的一个代表性矿床,产于早二叠世大石寨组火山-沉积岩与早白垩世敖包吐花岗岩的接触带上。文章通过分析该矿床岩、矿石的微量元素和稀土元素,揭示出萤石的成矿作用可分为2个阶段,即交代作用和充填作用。交代作用过程中大石寨组的结晶灰岩可能为萤石的形成提供了部分Ca来源,萤石矿石的稀土元素配分模式与海水基本类似,具有Ce负异常;成矿作用后期主要表现为充填作用,形成颗粒粗大的萤石,表现为重稀土元素富集的特征,并随着萤石的沉淀析出,稀土元素总量逐渐下降,反映出成矿流体经历了较长期的演化过程。各地层单元、花岗岩体和萤石矿石的Sr、Nd、Pb同位素研究表明,萤石的放射性同位素组成具有壳、幔源混合的特点,成矿物质来源具有多源性。早白垩世敖包吐花岗岩可能是萤石中F的主要来源,而大石寨组的结晶灰岩则可能提供了Ca。另外,Pb、Nd同位素的极大不均一性,有可能是成矿流体在运移过程中对艾力格庙群放射性组分的选择性吸收的结果。萤石成矿作用与钾玄岩的时空关系暗示了萤石的成矿过程可能是中国东部岩石圈减薄和下地壳的置换地质事件的结果。在构造转型的过程中,燕山中期富碱的酸性花岗岩浆的活动分异出富含F的成矿流体,与幔源流体混合,沿区域重新活化的深大断裂和大石寨组的层间破碎带上升,交代其间的灰岩透镜体,从而形成敖包吐中型萤石矿床。     

新疆阿尔泰蒙库铁矿床的成矿流体及成矿作用

蒙库大型铁矿床赋存于上志留统—下泥盆统康布铁堡组变质火山-沉积岩系中,容矿岩石为石榴子石矽卡岩、变粒岩、浅粒岩和大理岩。矿体总体顺层分布,空间上与矽卡岩密切相关。研究表明,矽卡岩期石榴子石以发育玻璃质熔融包裹体、流体熔融包裹体和流体包裹体为特征,晚期矽卡岩阶段矿物中发育液相包裹体,变质期矿物中主要发育液相包裹体和含子矿物包裹体。矽卡岩期熔融包裹体的均一温度为1100℃,早期矽卡岩阶段流体包裹体均一温度变化于193～499℃,在450℃、350℃和230℃出现峰值。中期矽卡岩阶段均一温度变化于236～550℃,峰值为350℃。区域变质期均一温度介于132～513℃,在350℃、230℃和190℃出现峰值。流体包裹体的盐度w(NaCleq)介于1.23%～60.31%,流体密度变化于0.60～1.16g/cm3。石榴子石、石英和方解石的δ18OSMOW变化于0.2‰～8.4‰,δ18OH2O介于-5.1‰～5.33‰,δD为-127‰～-81‰,表明矽卡岩期成矿流体主要是岩浆水,混合少量大气降水;变质期流体主要为大气降水,为混合变质水。方解石δ13CPDB变化于-6.1‰～-2.3‰,表明流体中碳来自深部或地幔。成矿时代为早泥盆世早期(略晚于404～400Ma),成矿作用与矽卡岩的退化变质作用有关。     

云南官房铜矿床矿石矿物特征及银的赋存状态

通过显微镜鉴定、电子探针(EPMA)及扫描电镜能谱分析(SEM/EDS)等方法,首次对官房铜矿的矿物组合和银的赋存状态进行了研究。初步查明,矿石矿物为中-低温热液成因,并受火山机构及断裂构造的控制;银矿物主要为碲银矿和辉银矿。矿石中银与铜呈明显正相关关系,而方铅矿中不含银。银主要以类质同象的形式赋存于含铜矿物或黄铁矿中;银的独立矿物含量低,且多呈包裹体的形式存在于黄铜矿、斑铜矿及黄铁矿中,或以微细粒状赋存于矿物颗粒间和斑铜矿的表面。