Overbreak and underbreak in underground openings Part 2: causes and implications

Summary The newly developed light sectioning method has been used to investigate some of the causes and costs of overbreak and underbreak. Investigations at the Aquamilpa Hydroelectric Project in Mexico have shown decreased overbreak and increased underbreak as a result of increased rock quality and decreased explosive energy. A new measure of explosive energy, the perimeter powder factor (PPF), has been defined and shown to be useful in the context of tunnel-wall rock damage. Tentative results indicate that explosive energy (PPF) may be a more important factor in producing underbreak, whereas rock quality may be a greater factor in producing overbreak. A site-specific equation is given for predicting overbreak or underbreak as a function of rock quality and explosive energy, with an evaluation of the cost of underbreak and overbreak.     

The origin of accretionary lapilli

Experimental investigations in a recirculating wind tunnel of the mechanisms of formation of accretionary lapilli have demonstrated that growth is controlled by collision of liquid-coated particles, due to differences in fall velocities, and binding as a result of surface tension forces and secondary mineral growth. The liquids present on particle surfaces in eruption plumes are acid solutions stable at 100% relative humidity, from which secondary minerals, e.g. calcium sulphate and sodium chloride, precipitate prior to impact of accretionary lapilli with the ground. Concentric grain-size zones within accretionary lapilli build up due to differences in the supply of particular particle sizes during aggregate growth. Accretionary lapilli do not evolve by scavenging of particles by liquid drops followed by evaporation — a process which, in wind tunnel experiments, generates horizontally layered hemispherical aggregates. Size analysis of particles in the wind tunnel air stream and particles adhering to growing aggregates demonstrate that the aggregation coefficient is highly grain-size dependent. Theoretical simulation of accretionary lapilli growth in eruption plumes predicts maximum sizes in the range 0.7–20 mm for ash cloud thicknesses of 0.5–10 km respectively.     

钻孔灌注桩施工对邻近运营隧道变形影响研究

桩基施工将引起周边地层位移和邻近隧道结构变形,以南京龙津桥改建项目桩基工程为背景,通过现场实测,分析研究钻孔灌注桩施工全过程各工况条件对地层位移场和邻近既有隧道结构变形的影响规律。结果表明:由于钢套管的护壁作用,钻孔灌注桩施工过程中产生的最大地层位移和隧道结构变形较小,说明采用“钢套管边旋压边取土”、“群桩间跳施工”等工艺,对周围土体扰动影响程度较小,建议近隧桩基工程采用全套管灌注桩的施工方法,监测分析结果可为类似工程提供技术参考。     

Treatment of high fluoride concentration wastewater by layered double hydroxides： Mechanism studies

An appropriate concentration of fluoride in drinking water is required to prevent dental cavities, but long-term ingestion of water that contains more than a suitable level of fluoride can cause bone disease and mottling of the teeth. Fluoride ions can be found in wastewater from the fluoride chemical industry, as well as the semiconductor, metal processing, fertilizer, and glass-manufacturing industries. The discharge standard for fluoride in industrial wastewater in China is 10 mg/L. Efficient treatment of fluoride-containing wastewater is therefore of major concern in China, following the rapid development of the fluoride chemical industry. Several methods have been used to remove fluoride from water, such as adsorption, chemical precipitation, electrodialysis, ion exchange and electrochemical processes. Layered double hydroxides （LDHs） are anionic clays with high anion exchange capacities which are effective adsorbents for removal of a variety of anionic pollutants. LDHs have been studied as potential adsorbents for removing toxic anionic species such as CrO4^2-, TcO4^-, SeO3^2-, pesticides, and anionic surfactants from aqueous systems. One of the main attractions of using LDHs for fluoride removal, is that unlike other chemical treatment methods, no chemical sludge should be produced. In the present study, an attempt was made to investigate the mechanism of fluoride removal by LDHs under different conditions using batch methods. In addition, the release of fluoride adsorbed on LDHs by treatment with an aqueous solution of Na2CO3 was studied. The residual fluoride was found to be 10 mg/L in a solution with an initial concentration of 1000 mg/L, which meets the discharge standard for fluoride in industrial wastewater in China.     

Structural Evolvement of Heating Treatment of Mg/AI-LDH and Preparation of Mineral Mesoporous Materials

Although hydrotalcite, or layered double hydroxides （LDHs）, is not a common mineral, it is an important material that can be easily synthesized in laboratory. In this study, structural evolvement and BET surface area changes of heat treated Mg/AI-LDH is evaluated by XRD, TEM and N2-BET analyses. The results indicate that the magnesium-aluminum LDH with carbonate as interlayer anion, periclase-like oxides was formed at temperatures of 400-800℃. Meanwhile, 2-3 nanometer mesoporous were formed during decomposition of LDH. However, the heat treated samples still preserve the morphology of the original LDH plates. Periclase-like formed from LDH heat treatment may re-hydrolyze and recover the structure of LDH. However, crystallinity of the recovered LDH is lower than that of the original LDH. This heat treatment will result in formation of （Mg, Al）-oxide nano-crystals and nanopores among the nano-crystals. When heating temperature exceeds 1000, the periclase-like （Mg, Al）-oxide is transformed into a composite with periclase （MgO） and spinel phases. The periclase can be re-hydrolyzed and dissolved in HCl solution. After acid treatment, the sample with a high surface area is composed of spinel nano-crystals and nanopores among them. Our results will provide a new and economic way to synthesize mesoporous materials through pathways of phase transformation of precursor materials with different composition.     

关于角平分线法建立线状缓冲区算法的改进

分析了用对角平分线法建立缓冲区的算法,提出了一种新的求角平分线和缓冲点的方法,实践证明其在算法实现方面是可行的,而且效果比较理想。     

惯性／双星组合导航系统的滤波与仿真

介绍了惯性导航系统和双星导航系统各自的运行方式和优缺点；详细推导了组合导航系统的误差方程和量测方程；介绍了Kalman滤波的整个过程并最后进行了仿真计算。仿真结果显示，惯性导航系统和双星导航系统的组合弥补了各自的不足，具有较好的精度和可靠性。     

风沙起电的风洞实验研究

利用大型风沙物理风洞实验装置 ,模拟铺沙地面在不同风速条件下对不同粒径的沙样和混合沙的起电电场、电位和荷质比作实验测量。结果表明 :存在风沙起电效应。风洞内电场多为负极性 ,最大电场达到 - 2 9kV·m- 1 ,导线电位可达 12 0mV。沙粒越细 ,起电越强 ,且随风速增加而增大     

Near-Wall Flow Development After A Step Change In Surface Roughness

An experimental study of the initial flow field downstream of a step change in surface roughness is presented. The roughness length of the downstream surface was approximately tenfold that of the upstream roughness and, unlike all previous studies, attention was concentrated on the roughness sublayer region beneath the inertial (log-law) region. The experiments were conducted at a boundary layer Reynolds number of about 6 × 10⁴ (based on layer thickness andfree-stream velocity) and around a longitudinal location where the (downstream) roughness length, z_o2, was about 1% of the boundary-layer thickness atthe roughness change point.The thickness of the roughness sublayer was found for the two roughness. It was observed that the vertical profiles of mean velocity and turbulence characteristics started to show similarity after about 160z₀₂ downstream of the roughness change. The presence of a shear stress overshoot is shown to depend strongly on the precise location (with respect to the roughness elements) at which the measurements are made and the thickness of the equilibrium layer is shown to be very sensitive to the way it is defined. It is demonstrated that the growing equilibrium layer has first to encompass the roughness sublayer before any thickness of inertial sublayer can be developed. It follows that, in somepractical cases, like flows across some urban environments, the latter(log-law) region may never exist at all.     

内蒙古大青山地区寒武系与奥陶系之间的一个重要的层序界面

大青山地区寒武纪－奥陶纪地层分布零星，是由中生代逆冲推覆构造就位于此的一系列近东西向延展的构造岩片组成。下寒武统色麻沟组直接覆盖在太古界变质岩之上，缺失中元古界什那干群，寒武系与奥陶系之间呈假整合接触，标志着区内寒武纪与奥陶纪之间发生过一次抬升构造运动，其形成机制与古亚洲洋内的稳定陆快向华北板块拼贴事件有关，是早奥陶世末期华北板块整体抬升的序幕。这个层序界面的认识，对于恢复华北板块北部边缘构造演化历史具有重要意义。