基于破碎临界区的新型拍岸浪统计计算模型研究

When waves propagate from deep water to shallow water, wave heights and steepness increase and then waves roll back and break. This phenomenon is called surf. Currently, the present statistical calcula...     

东海区小黄鱼渔业生物学现状的分析

以2001年东海区渔业资源监测调查资料为依据，对小黄鱼的体长、体重、生长、死亡等渔业生物学特征及临界年龄等进行了分析研究。结果表明，目前东海区小黄鱼优势体长组为110～130mm，占41．34％；优势体重组为20～40g，占50．91％；总死亡系数为2．05，自然死亡系数为0．58，捕捞死亡系数为1．47，临界年龄为2．18龄。对照东海区小黄鱼生物学特征的历史状况分析，目前东海区小黄鱼个体小型化、低龄化、性成熟提早现象明显，生物学参数发生较大变化。建议在东海区现行资源状态下，小黄鱼的可捕标准应充分考虑其生物学现状加以科学调整。     

中地壳的地球化学动力学和矿石成因

笔者重点进行了大于300℃——在近临界区至超临界区条件下的硅酸盐矿物与水反应动力学实验。矿物(钠长石Ab、透辉石Di、阳起石Act和磁铁矿Mt)的溶解反应动力学实验是使用流体通过叠层反应器的开放体系在25～400℃和22MPa下完成的。实验发现矿物在300℃至400℃范围,在跨越水临界点时出现反应速率的涨落。各种多金属氧化物硅酸盐与水反应时,各个元素溶解到溶液里的释放速率一般不一样,常称为一致溶解作用。但是,在近300℃变为一致溶解作用。实验发现在22MPa时硅酸盐矿物的最大溶解反应速率多是在300℃,如硅的最大释放速率是在300℃。其余元素如Na、K、Mg、Ca、Fe、Al等释放速率在<300℃22MPa时都高于硅的释放速率,在>300℃时硅的释放速率要高于其它元素的释放速率。确切地说,金属与氧之间的键的性质决定了它们(金属氧化物)与水之间反应速率。在一般情况下,Na-Obr,Ca-Obr,Mg-Obr,Al-Obr和Si-Obr的键桥(br),它们之间相对地由具有离子键性质逐步变为具有极性键的性质。由常温常压到亚临界区(300～374℃22MPa),再到大于临界点374℃、22MPa进入超临界区,水的性质随温度、压力变化。水由容易溶解离子键逐渐变为容易打破极性键。笔者还研究了黑钨矿、锡石(玄武岩、花岗闪长岩)与水在250～400℃条件下的反应动力学过程,得出了相同的结果。实验均发现在跨越水临界点时矿物(或岩石)与水反应的动力学涨落。这些实验结果可以用于说明中地壳上部的水/岩相互作用的特征。发生于中地壳的水、岩相互作用大多是在300～450℃和20～50MPa条件下进行的。各地区的地壳厚度不一,中地壳温度压力并不完全相同。模拟中地壳条件下水/岩相互作用实验,目的主要是研究矿物(或岩石)在300～450℃条件下反应动力学过程。已有热液矿床矿物流体包体数据表明:有一批矿床的主要矿石形成于300～500℃,低于NaCl H2O溶液临界线的条件。中地壳的流体处于由亚临界态跨越临界态,进入超临界流体太的演化过程。这种流体的性质变化会引起水/岩相互作用的反应动力学涨落和矿石大量沉淀。     

驯化水温及温升速率对三门湾三种虾蟹类热耐受性的影响

作者采用动态实验法与静态实验法相结合的方法,研究了三门湾脊尾白虾(Exopalaemon carinicauda)、口虾蛄(Oratosquilla oratoria)和日本(Charybdis japonica)在不同季节的基础水温即驯化水温(8~29℃)和温升速率(0.5~15.0℃/h)下的热耐受能力。结果表明,驯化水温和温升速率对各实验动物的热耐受性均有显著影响。实验动物的热耐受性与驯化水温总体上呈显著正相关,而温升速率对热耐受性的影响具有物种特异性,并受驯化水温制约;在不同驯化水温下,各实验动物的热耐受性随温升速率增大呈不同变化趋势。各实验动物的24 h高起始致死温度受驯化水温的影响显著,随着驯化水温从8℃升高到29℃,脊尾白虾、日本和口虾蛄的24hUILT50分别从24.2、34.6、24.9℃显著增大到35.3、37.4和34.4℃。结合3种实验动物的最大临界温度分析,它们的热耐受能力依次为:日本脊尾白虾口虾蛄。研究结果可为探究三门湾水域潜在的热污染状况及其生态环境效应提供科学依据。     

实验研究岩石圈深部流体及相关科学问题

实验研究地球岩石圈深部流体和对地球深部流体的观测发现,水溶液在跨越临界态时有许多特殊性质。使用水热金刚石压钻在200～800MPa,300～700℃条件下,可观测到：NaCl-H2O溶液两相不混溶相区的结构和近临界态现象。测量高温高压下NaCl溶液的电导率,在近临界和跨越临界态时发现最大电导率值。在对大洋中脊热水观测中可发现大多数喷口是在2200m深。喷口正在近临界态条件下喷出含矿流体。这些临界态研究对于重新分析岩石圈的地球物理测量结果和对认识大陆岩石圈内流体性质有很大意义。     

钦州湾潮流深槽的成因与稳定性探讨

据钦州湾2007年1—2月的实测潮流,结合径流、潮汐等资料,经水动力和港湾地形综合分析揭示:钦州湾的潮流深槽是潮流作用于葫芦形复式港湾的必然产物,是在内湾纳潮蓄能、湾颈狭道强流、颈口岛礁分流喷射冲刷而成的。通过对潮流流路和强度的分析,对潮流深槽的稳定性进行了探讨;进而通过湾颈流速-内湾纳潮关系计算,给出了潮流深槽稳定的临界条件。     

Selection of sand models and identification of parameters using an enhanced genetic algorithm

Numerous constitutive models of granular soils have been developed during the last few decades. As a consequence, how to select an appropriate model with the necessary features based on conventional tests and with an easy way of identifying parameters for geotechnical applications has become a major issue. This paper aims to discuss the selection of sand models and parameters identification by using genetic algorithm. A real‐coded genetic algorithm is enhanced for the optimization with high efficiency. Models with gradually varying features (elastic‐perfectly plastic modelling, nonlinear stress–strain hardening, critical state concept and two‐surface concept) are selected from numerous sand models as examples for optimization. Conventional triaxial tests on Hostun sand are selected as the objectives in the optimization. Four key points are then discussed in turn: (i) which features are necessary to be accounted for in constitutive modelling of sand; (ii) which type of tests (drained and/or undrained) should be selected for an optimal identification of parameters; (iii) what is the minimum number of tests that should be selected for parameter identification; and (iv) what is the suitable and least strain level of objective tests to obtain reliable and reasonable parameters. Finally, a useful guide, based on all comparisons, is provided at the end of the discussion. Copyright © 2015 John Wiley & Sons, Ltd.     

Explicit integration of bounding surface model for the analysis of earthquake soil liquefaction

This paper presents a new plasticity model developed for the simulation of monotonic and cyclic loading of non‐cohesive soils and its implementation to the commercial finite‐difference code FLAC, using its User‐Defined‐Model (UDM) capability. The new model incorporates the framework of Critical State Soil Mechanics, while it relies upon bounding surface plasticity with a vanished elastic region to simulate the non‐linear soil response. Stress integration of constitutive relations is performed using a recently proposed explicit scheme with automatic error control and substepping, which so far has been employed in the literature only for constitutive models aiming at monotonic loading. The overall accuracy of this scheme is evaluated at element level by simulating cyclic loading along complex stress paths and by using iso‐error maps for paths involving change of the Lode angle. The performance of the new constitutive model and its stress integration scheme in complex boundary value problems involving earthquake‐induced liquefaction is evaluated, in terms of accuracy and computational cost, via a number of parametric analyses inspired by the successful simulation of the VELACS centrifuge Model Test No. 2 studying the lateral spreading response of a liquefied sand layer. Copyright © 2009 John Wiley & Sons, Ltd.     

求解非线性有限元方程的弧长法及在工程稳定分析中的应用

本文讨论了求解非线性有限元方程弧长法的基本原理及具体实施,并应用于压杆及滑块的稳定性分析。由于弧长法具有确定并通过结构临界应力状态的临界荷载值,因此可以应用于工程稳定性分析。算例表明,弧长法确定的临界荷载值是令人满意的。     

Hydrothermal Alteration Zoning and Kinetic Process of Mineral-Water Interactions

This study reports the kinetic experimental results of albite in water and in KCI solution at 22 MPa in the temperature range of 25 to 400℃. Kinetic experiments have been carried out in an open flow-through reaction system (packed bed reactor). Albite dissolution is always incongruent in water at most temperatures, but becomes congruent at 300℃ (close to the critical point 374℃). At temperatures from 25 to 300℃, the incongruent dissolution of albite is reflected by the fact that sodium and aluminum are easily dissolved into water; from 300 to 400℃ it is reflected by silicon being more easily dissolved in water than Al and Na. Maximum albite dissolution rates in the flow hydrothermal systems have been repeatedly observed at 300℃, independent of flow rates.The kinetic experiments of albite dissolution in a KCl aqueous solution (0.1 mol KCl) indicate that the dissolution rate of albite increases with increasing temperature. Maximum silicon release rates of albite have been observed at 400℃, while ma