Sediment transport in analogue flume models compared with real‐world sedimentary systems: a new look at scaling evolution of sedimentary systems in a flume

Evolution of sedimentary systems at large temporal and spatial scales cannot be scaled down to laboratory dimensions by conventional hydraulic Froude scaling. Therefore, many researchers question the validity of experiments aiming to simulate this evolution. Yet, it has been shown that laboratory experiments yield stratigraphic responses to allocyclic forcing that are remarkably similar to those in real‐world prototypes, hinting at scale independency with strong dependence on boundary conditions but weak dependence on the actual sediment transport dynamics. This paper addresses the dilemma by contrasting sediment transport rules that apply in the laboratory with those that apply in real‐world geological systems. It is demonstrated that the generation of two‐dimensional stratigraphy in a flume can be simulated numerically by the non‐linear diffusion equation. Sediment transport theory is used to demonstrate that only suspension‐dominated meandering rivers should be simulated with linear diffusion. With increasing grain‐size (coarse sand to gravel) and shallowness of river systems, the prediction of long‐term transport must be simulated by non‐linear, slope‐dependent diffusion to allow for increasing transport rates and thus change in stratigraphic style. To point out these differences in stratigraphic style, three stages in infill of accommodation have been defined here: (i) a start‐up stage, when the system is prograding to base level (e.g. the shelf edge) with no sediment flux beyond the base‐level point; (ii) a fill‐up stage, when the system is further aggrading while progressively more sediment is bypassing base level with the progression of the infill; and (iii) a keep‐up stage, when more than 90% of the input is bypassing the base level and less than 10% is used for filling the accommodation. By plotting the rate of change in flux for various degrees of non‐linearity (varying the exponent in the diffusion equation) it was found that the error between model and real‐world prototype is largest for the suspension‐dominated prototypes, although never more than 30% and only at the beginning of the fill‐up stage. The error reduces to only 10% for the non‐linear sandy‐gravelly and gravelly systems. These results are very encouraging and open up ways to calibrate numerical models of sedimentary system evolution by such experiments.     

Discriminating between pore‐filling load and bed‐structure load: a new porosity‐based method,exemplified for the river Rhine

Sediments contained in the river bed do not necessarily contribute to morphological change. The finest part of the sediment mixture often fills the pores between the larger grains and can be removed without causing a drop in bed level. The discrimination between pore‐filling load and bed‐structure load, therefore, is of practical importance for morphological predictions. In this study, a new method is proposed to estimate the cut‐off grain size that forms the boundary between pore‐filling load and bed‐structure load. The method evaluates the pore structure of the river bed geometrically. Only detailed grain‐size distributions of the river bed are required as input to the method. A preliminary validation shows that the calculated porosity and cut‐off size values agree well with experimental data. Application of the new cut‐off size method to the river Rhine demonstrates that the estimated cut‐off size decreases in a downstream direction from about 2 to 0·05 mm, covariant with the downstream fining of bed sediments. Grain size fractions that are pore‐filling load in the upstream part of the river thus gradually become bed‐structure load in the downstream part. The estimated (mass) percentage of pore‐filling load in the river bed ranges from 0% in areas with a unimodal river bed, to about 22% in reaches with a bimodal sand‐gravel bed. The estimated bed porosity varies between 0·15 and 0·35, which is considerably less than the often‐used standard value of 0·40. The predicted cut‐off size between pore‐filling load and bed‐structure load (D_c,p) is fundamentally different from the cut‐off size between wash‐load and bed‐material load (D_c,w), irrespective of the method used to determine D_c,p or D_c,w. D_c,w values are in the order of 10^?1 mm and mainly dependent on the flow characteristics, whereas D_c,p values are generally much larger (about 10⁰ mm in gravel‐bed rivers) and dependent on the bed composition. Knowledge of D_c,w is important for the prediction of the total sediment transport in a river (including suspended fines that do not interact with the bed), whereas knowledge of D_c,p helps to improve morphological predictions, especially if spatial variations in D_c,p are taken into account. An alternative to using a spatially variable value of D_c,p in morphological models is to use a spatially variable bed porosity, which can also be predicted with the new method. In addition to the morphological benefits, the new method also has sedimentological applications. The possibility to determine quickly whether a sediment mixture is clast‐supported or matrix‐supported may help to better understand downstream fining trends, sediment entrainment thresholds and variations in hydraulic conductivity.     

Sedimentary evolution of a Late Pleistocene temperate red algal reef (Coralligène) on Rhodes,Greece: correlation with global sea‐level fluctuations

Autochthonous red algal structures known as coralligène de plateau occur in the modern warm‐temperate Mediterranean Sea at water depths from 20 to 120 m, but fossil counterparts are not so well‐known. This study describes, from an uplifted coastal section at Plimiri on the island of Rhodes, a 450 m long by 10 m thick Late Pleistocene red algal reef (Coralligène Facies), interpreted as being a coralligène de plateau, and its associated deposits. The Coralligène Facies, constructed mainly by Lithophyllum and Titanoderma, sits unconformably upon the Plio‐Pleistocene Rhodes Formation and is overlain by a Maerl Facies (2 m), a Mixed Siliciclastic‐Carbonate Facies (0·2 m) and an Aeolian Sand Facies (2·5 m). The three calcareous facies, of Heterozoan character, are correlated with established members in the Lindos Acropolis Formation in the north of the island, while the aeolian facies is assigned to the new Plimiri Aeolianite Formation. The palaeoenvironmental and genetic‐stratigraphic interpretations of these mixed siliciclastic‐carbonate temperate water deposits involved consideration of certain characteristics associated with siliciclastic shelf and tropical carbonate shelf models, such as vertical grain‐size trends and the stratigraphic position of zooxanthellate coral growths. Integration of these results with electron spin resonance dates of bivalve shells indicates that the Coralligène Facies was deposited during Marine Isotope Stage 6 to 5e transgressive event (ca 135 to 120 ka), in water depths of 20 to 50 m, and the overlying Maerl Facies was deposited during regression from Marine Isotope Stage 5e to 5d (ca 120 to 110 ka), at water depths of 25 to 40 m. The capping Aeolian Sand Facies, involving dual terrestrial subunits, is interpreted as having formed during each of the glacial intervals Marine Isotope Stages 4 (71 to 59 ka) and 2 (24 to 12 ka), with soil formation during the subsequent interglacial periods of Marine Isotope Stages 3 and 1, respectively. Accumulation rates of about 0·7 mm year^?1 are estimated for the Coralligène Facies and minimum accumulation rates of 0·2 mm year^?1 are estimated for the Maerl Facies. The existence of older red algal reefs in the Plimiri region during at least Marine Isotope Stages 7 (245 to 186 ka) and 9 (339 to 303 ka) is inferred from the occurrence of reworked coralligène‐type lithoclasts in the basal part of the section and from the electron spin resonance ages of transported bivalve shells.     

Palaeoenvironmental significance of Late Permian palaeosols in the South‐Eastern Iberian Ranges,Spain

The Late Permian (Wuchiapingian) Alcotas Formation in the SE Iberian Ranges consists of one red alluvial succession where abundant soil profiles developed. Detailed petrographical and sedimentological studies in seven sections of the Alcotas Formation allow six different types of palaeosols, with distinctive characteristics and different palaeogeographical distribution, to be distinguished throughout the South‐eastern Iberian Basin. These characteristics are, in turn, related to topographic, climatic and tectonic controls. The vertical distribution of the palaeosols is used to differentiate the formation in three parts from bottom to top showing both drastic and gradual vertical upwards palaeoenvironmental changes in the sections. Reconstruction of palaeoenvironmental conditions based on palaeosols provides evidence for understanding the events that occurred during the Late Permian, some few millions of years before the well‐known Permian‐Triassic global crisis.     

Carbonate aeolianites of western Saurashtra,India: experimental decipherment of the depositional mechanisms

Granular carbonate deposits of Late Pleistocene to Early Holocene age, commonly referred to as ‘miliolite limestone’, occur in a linear belt, parallel to the southern coast of Saurashtra, India. In the present study area these carbonate deposits are found in select valleys between ridges and mounds of pyroclastic material present in the Deccan trap plateau. Two different depositional histories have been proposed for these sediments. The presence of marine bioclasts led to the postulation of a marine origin for these deposits. The second school of thought propounded redeposition of the coastal sediments by aeolian processes. Although a few features could not be explained by the proposed aeolian model, critical comparison of these two views favoured the aeolian origin. The mode of occurrence, lithological and structural attributes, and microscopic evidence presented here, also support a possible aeolian origin for these deposits. Experimental observation indicates that these carbonate aeolianites represent backflow deposits, which accumulated because of the flow separation caused by the presence of topographic highs. The conspicuous concave‐up geometry of the deposit conformed to the shape of the separation bulb. In view of the inferred depositional mechanism, the disposition of the deposits and the signature of the palaeoflow direction suggest that the carbonate particles were derived from the north‐western coast of Saurashtra by strong south‐easterly winds. Massive granular carbonates with outsized basement clasts appear to be the product of avalanching of granular material from the higher contours because of oversteepening of the primary deposit.     

Opening of the Fram Strait gateway: A review of plate tectonic constraints

We have revised the regional crustal structure, oceanic age distribution, and conjugate margin segmentation in and around the Lena Trough, the oceanic part of the Fram Strait between the Norwegian–Greenland Sea and the Eurasia Basin (Arctic Ocean). The Lena Trough started to open after Eurasia–Greenland relative plate motions changed from right-lateral shear to oblique divergence at Chron 13 times (33.3 Ma; earliest Oligocene). A new Bouguer gravity map, supported by existing seismic data and aeromagnetic profiles, has been applied to interpret the continent–ocean transition and the influence of Eocene shear structures on the timing of breakup and initial seafloor spreading. Assuming that the onset of deep-water exchange depended on the formation of a narrow, oceanic corridor, the gateway formed during early Miocene times (20–15 Ma). However, if the initial Lena Trough was blocked by terrigenous sediments or was insufficiently subsided to allow for deep-water circulation, the gateway probably formed with the first well developed magnetic seafloor spreading anomaly around Chron 5 times (9.8 Ma; Late Miocene). Paleoceanographic changes at ODP Site 909 (northern Hovgård Ridge) are consistent with both hypotheses of gateway formation. We cannot rule out that a minor gateway formed across stretched continental crust prior to the onset of seafloor spreading in the Lena Trough. The gravity, seismic and magnetic observations question the prevailing hypotheses on the Yermak Plateau and the Morris Jesup Rise as Eocene oceanic plateaus and the Hovgård Ridge as a microcontinent.     

新疆塔里木北缘色日牙克依拉克一带泥盆纪花岗质侵入体的确定及其地质意义

位于新疆南天山色日牙克依拉克一带发育较多的中酸性侵入岩,前人均划为石炭纪侵入岩,作者对其中花岗闪长岩锆石进行SHRIMP定年,获得侵入岩形成年龄387±8Ma,另有一组捕获锆石的年龄为418.4±6.5Ma,通过对这些侵入岩的岩石学研究,结果显示该区泥盆纪侵入岩均具较典型活动陆缘侵入岩的特征.结合区域岩浆活动资料及前人成果,初步确定在塔里木北缘木札尔特、色日牙克依拉克、虎拉山南缘野云沟至库尔勒一带在古生代为一活动陆缘.     

河南洛宁段河金矿流体包裹体研究和矿床成因

河南省洛宁县段河石英脉型金矿主要包括石寨沟和岭东两个矿区,分别由3～4条含金石英脉构成。矿化过程从早到晚包括石英-黄铁矿、石英-多金属硫化物和石英-碳酸盐等3个阶段．其中中阶段金矿化最强,次为早阶段。各阶段石英中流体包裹体以气液两相包裹体为主．次为纯液体包裹体。激光拉曼测试表明,气液两相包裹体的液相为H2O,气相主要为Ho和CO2混合、纯H2O,次为纯CO2;纯液体包裹体为纯H2O。石寨沟矿区包裹体均一温度从早到晚依次为240．9～315．9℃．188．7～304．5℃,137．3～259．3℃：流体盐度变化依次为（6．74～12．85）wt%NaCl．eq,（2．41～8．68）wt％NaCl．eq,（2．24-7．86）wt%NaCl．eq。岭东矿区均一温度从早到晚依次为303．7-343．1℃,251．8-325．4℃,305．7～355．0℃：流体盐度变化依次为（5．11～11．70）wt％NaCl．eq,（2．74-10．11）wt％NaCl．eq,（0．53-6．74）wt％NaCl．eq。两矿区主成矿期流体均为中温、低盐度,早阶段流体为改造热液和变质热液的混合体,含一定量CO2,且流体CO2含量和盐度从早到晚逐渐降低。石寨沟矿区包裹体均一温度逐渐降低,而岭东矿区包裹体均一温度先降后升,加之岭东矿区各阶段成矿温度均高于石寨沟矿区．表明成矿流体系统主要受岩浆热驱动,岭东矿区更靠近岩体,且在晚阶段又有脉动性的岩浆加热．段河金矿区南部存在隐伏岩体。     

P-III分布参数的概率权重矩法S函数计算

概率权重矩法是一种估计统计分布参数的方法.本文根据不完全Γ函数在无限区间积分,推导了P-Ⅲ分布参数的S函数的计算公式.通过现有计算公式比较,其计算结果具有较高的计算精度,避免了的大量的数值积分计算.文中公式只要借助于计算编程进行求解,给定超几何函数项一定的截断误差,其运算具有较高的运行速度.文中计算公式是一种P-Ⅲ分布参数S函数的计算途径.