Penetration response of spudcans in layered sands

The behaviour of spudcan foundations during the installation and preloading in two-layer sand sediments was investigated through large deformation finite element (LDFE) analyses. The LDFE analyses were carried out using the coupled Eulerian-Lagrangian approach, modifying Mohr-Coulomb soil model to capture hardening and subsequent softening effects of sand. Parametric analyses were undertaken varying the top layer thickness, relative density of sand and spudcan diameter. Both loose to medium dense-over-dense and dense-over-loose to medium dense sand deposits were explored. The results showed that, for the investigated relatively thin top layer thickness of ≤ 5 m, spudcan behaviour was dictated by the bottom sand layer with a minimal influence of the top layer. For assessing the penetration resistance profile in two-layer sands, the performance of the ISO, SNAME, InSafeJIP, and other existing theoretical design methods were evaluated.     

Hydrodynamic performance of a T-shaped floating breakwater

The comprehensive utilization of floating breakwaters, specially acting as a supporting structure for offshore marine renewable energy explorations, has received more and more attention recently. Based on linear water-wave theory, the hydrodynamic performance of a T-shaped floating breakwater is semi-analytically investigated through the matched eigenfunction expansion method (MEEM). Auxiliary functions, to speed up the convergence and improve the accuracy in the numerical computations, are introduced to represent the singular behavior of fluid field near the lower salient corners of the structure. The effects of the height and installation position of the vertical screen on the reflection and transmission coefficients, dynamic response and wave forces are examined. It is found that the presence of the screen shifts the resonance frequency of RAO for both surge and pitch modes to the low-frequency area, while has no effect on heave mode. The identical added masses, damping and transmission coefficients can be obtained in the cases where the screen holds the same distance away from the longitudinal central axis of the upper box-type structure. Moreover, a relatively small pitch response can be achieved in a wide wave–frequency range, when the breakwater is Γ-shaped.     

An efficient and robust approach to predict ship self-propulsion coefficients

Achieving a reliable and accurate numerical prediction of the self-propulsion performance of a ship is still an open problem that poses some relevant issues. Several CFD methods, ranging from boundary element methods (BEM) to higher-fidelity viscous Reynolds averaged Navier–Stokes (RANS) based solvers, can be used to accurately analyze the separate problems, i.e. the open water propeller and the hull calm water resistance. However, when the fully-coupled self-propulsion problem is considered, i.e. the hull advancing at uniform speed propelled by its own propulsion system, several complexities rise up. Typical flow simplifications adopted to speed-up the simulations of the single analysis (hull and propeller separately) lose their validity requiring a more complex solver to tackle the fully-coupled problem. The complexity rises up further when considering a maneuver condition. This aspect increases the computational burden and, consequently, the required time which becomes prohibitive in a preliminary ship design stage.The majority of the simplified methods proposed in literature to include propeller effects, without directly solve the propeller flow, in a high-fidelity viscous solver are not able to provide all the commonly required self-propulsion coefficients. In this work, a new method to enrich the results from a body force based approach is proposed and investigated, with the aim to reduce as much as possible the computational burden without losing any useful result. This procedure is tested for validation on the KCS hull form in self-propulsion and maneuver conditions.     

CFD modelling of a small–scale fixed multi–chamber OWC device

Wave Energy Converters (WECs) have excellent potential as a source of renewable energy that is yet to be commercially realised. Recent attention has focused on the installation of Oscillating Water Column (OWC) devices as a part of harbor walls to provide advantages of cost–sharing structures and proximity of power generation facilities to existing infrastructure. In this paper, an incompressible three–dimensional CFD model is constructed to simulate a fixed Multi–Chamber OWC (MC–OWC) device. The CFD model is validated; the simulation results are found to be in good agreement with experimental results obtained from a scale physical model tested in a wave tank. The validated CFD model is then used for a benchmark study of 96 numerical tests. These investigate the effects of the PTO damping caused by the power take–off (PTO) system on device performance. The performance is assessed for a range of regular wave heights and periods. The results demonstrate that a PTO system with an intermediate damping can be used for all chambers in the MC–OWC device for most wave period ranges, except for the long wave periods. These require a higher PTO damping. An increased incident wave height reduces the device capture width ratio, but there is a noticeable improvement for long wave periods.     

波浪溢流作用下海堤内坡高性能加筋草皮护坡防侵蚀特征研究

基于1∶1的大型水槽试验结果,分析了波浪溢流过程中位于海堤内坡的高性能加筋草皮护面的侵蚀特征。试验观察表明试验期间有一定土壤的损失,但护坡无明显的破坏;土面高度测量表明,当土壤流失发展到一定深度后,如果水动力强度变化不大,侵蚀趋于逐渐停止,这种现象称为侵蚀上限;结合试验现象对侵蚀上限进行了初步解释,并讨论了侵蚀上限达到前的侵蚀速率特征;植株密度监测表明,试验期间的草茎密度基本不变,草叶密度在开始几次试验期间持续减小,而后达到一个稳定值,这对于海堤的可持续防护有重要意义。研究成果能够为波浪溢流期间海堤内坡防御的相关研究和工程措施提供参考依据。     

钙质土中重力串锚水平承载力特性有限元研究

目前没有规范给出串锚的水平承载力计算公式,为了利用有限元法研究串锚水平承载力特性,采用相关理论计算以及室内试验的方法来验证有限元法模拟计算的可靠性。实践证明,有限元法具有较高的计算精度。利用有限元分析软件ABAQUS建立了串锚-土体模型,模拟串锚在水平荷载作用下破坏过程,研究了串锚在水平荷载作用下破坏机理,从而得到了串锚水平承载力特性。在相同的工况条件下,串锚的水平承载力与其锚链长度有关,在一定范围内,增加锚链的长度可以提高串锚的水平承载力;串锚的水平承载力不是相应的单个锚的水平承载力相加,其水平承载力小于相应的单个锚水平承载力之和,在进行串锚水平承载力设计计算时应给与相应的考虑。     

多类重力场模型的精度分析

分析国际公布的EGM2008、GECO和EIGEN-6C4等超高阶重力场模型及GOCO03S、GOCONSGCF2DIRR5和GOCONSGCF2TIMR5等低阶重力场模型的内符合精度。利用实测的GNSS/水准数据对各模型进行外符合精度的检核。分析6个模型在不同阶次组合的精度,进而选取可靠的截断阶次确定组合重力场模型。计算结果表明:EGM2008、GECO、EIGEN-6C4及DIRR5四个重力场模型的阶方差均保持在mm级,而GOCO03S在191阶之后的精度达到dm级,TIMR5模型在228阶之后的精度达到dm级;6个重力场模型中,EIGEN-6C4模型的累计阶方差最小;EGM2008、GECO模型的互差阶方差在高频部分呈现差异,而在超高阶部分两种模型的互差阶方差符合性好;与EGM2008模型相比,其组合重力场模型高程异常精度最优可达0.063 m,精度提升幅度为15%,与GECO模型相比,其组合重力场模型高程异常精度最优可达0.060 m,精度提升幅度为23%,与EIGEN-6C4模型相比,其对应的组合重力场模型高程异常精度最优可达0.064 m,精度提升幅度为18%,因此,组合重力场模型能提高重力场模型高程异常的精度。     

Cartographic Design and the Space–Time Cube

This paper reports on the results of an empirical evaluation that aimed to define the effectiveness and efficiency of different visual variables in depicting the Space–Time Cube’s (STC) content. Existing STC applications demonstrate that the most used visual variables are size and colour hue. Less is known, however, about their usability metrics. The research sets design criteria for STC contents, such as space–time paths, based on the cartographic design theory. The visual variables colour hue, colour value, colour saturation, size and orientation have been applied in two different use case studies. Besides, to support the three-dimensional visual environment, depth cues such as shading and transparency were considered too. User tests have been executed based on real-world problems with particular attention for the visualization strategy and data complexity. The outcomes revealed the most efficient and effective visual variables to represent data of various complexities in the STC.     

Cartographic Symbol Design Considerations for the Space–Time Cube

The cartographic representation of geographic phenomena in the space–time cube comes with special challenges and opportunities when compared with two-dimensional maps. While the added dimension allows the display of attributes that vary with time, it is difficult to display rapidly varying temporal data given the limited display height. In this study, we adapt 2D cyclic point symbols to construct 3D surfaces designed along a helical path for the space–time cube. We demonstrate how these complex?3D helical surfaces can display detailed data, including data reported daily over 100 years and data reported in four-hour intervals over a year. To create the point symbols, each value is plotted along the curve of a helix, with each turn of the helix representing one year or week, respectively. The model is modified by varying the radii from the time axis to all points using the attribute value, in these cases maximum daily temperature and four-hourly ridership, and then creating a triangulated surface from the resulting points. Using techniques common to terrain representation, we apply hue and saturation to the surface based on attribute values, and lightness based on relief shading. Multiple surfaces can be displayed in a space–time cube with a consistent time interval facing the viewer, and the surfaces or viewer perspective can be rotated to display synchronized variations. We see this method as one example of how cartographic design can refine or enhance operations in the space–time cube.     

无人机倾斜摄影支持下的1∶500高精度三维测图方案及应用

研发了一种适合于大范围1∶500的无人机测图方案,围绕平面和高程点位中误差在5 cm以内这一核心目标,从无人机的平台稳定性、空中精准定位飞控、空三与三维建模及模型与影像结合的多视角测图等方面进行了设计。在广州马沥村的应用表明,本文研究的无人机倾斜摄影方案可以满足1∶500高精度的三维测图,并具有较高的效率。