上覆流沙层隧道开挖面稳定性分析与数值试验研究

为解决上覆流沙层隧道开挖面极易发生坍塌破坏的技术难题,以典型该地质条件下的青岛地铁M2号线啤苗区间（啤酒城站至苗岭路站）为研究对象,基于开挖面的实际破坏特征建立了开挖面失稳破坏力学模型,从功能转化平衡角度,进行了隧道开挖面稳定性上限分析,并利用强度折减与重力加载两种方式,提出了隧道开挖面安全系数,得到了不同开挖面土体黏聚力、摩擦角、重度、隔水层厚度及隧道开挖高度下的临界土体破裂范围及破裂模式。理论研究表明：随着开挖面土体黏聚力、摩擦角、隔水层厚度等参数的增加,开挖面安全系数不断增大,稳定性不断提高;随着土体重度、隧道开挖高度增加,开挖面安全系数不断减小,稳定性不断降低。通过建立不同工况的数值模型验证了理论研究的正确性,得到了上覆流沙层地质条件下开挖面的典型破坏模式和临界参数,并提出了相应工程建议。研究成果为青岛地铁M2号线的顺利贯通及该类地质条件下的隧道施工提供了理论指导和科学对策。     

大断面厚顶煤巷道顶板冒落破坏的上限分析

根据大断面厚顶煤巷道顶板的破坏特性,考虑了顶板围岩应力水平与支护荷载的影响,利用Hoek-Brown强度准则及其相关联的流动法则,构造出厚顶煤巷道顶板的冒落破坏机构。基于塑性力学中的上限分析方法,结合变分原理,推导得到了大跨度厚顶煤巷道顶板的冒落破坏机制,并以赵楼煤矿某巷道现场实践为例,分析了不同计算参数对顶板冒落破坏机制的影响。计算研究表明：随着岩体经验参数A、抗拉强度、抗压强度及支护荷载的增加,冒落体尺寸随之增大,而当岩体经验参数B、围岩应力及岩体重度增加时,冒落体尺寸则随之减小;冒落体尺寸代表了巷道顶板安全性能的大小,其尺寸越大,表明使巷道顶板发生冒落破坏所需外力功越多,顶板安全性能也越高;岩体经验参数B、围岩应力水平与支护荷载对顶板围岩破裂机制影响较为显著,参数B决定了冒落体的破裂形状,随着参数B的增加,冒落破裂迹线的曲率不断减小;增大支护阻力是提高顶板稳定性的有效途径,其研究结果可为大断面厚顶煤巷道支护设计提供一定的理论依据。     

安徽省琅琊山铜矿床深部资源潜力分析及勘查

通过矿山生产实践对控岩控矿构造的认识积累和矿区构造形迹的解析,结合CSAMT法测量所获得的异常,推断矿床岩体底部隐伏矿体的存在。经深部资源勘查项目的实施并得以验证,进而提出了下一步资源递进勘查的总体方向和目标。     

非均质与各向异性黏土基坑抗隆起稳定分析

经典的Prandtl 机构不能很好地反映支护结构入土深度的影响,也不能反映土体强度非均质和各向异性的影响。根据塑性极限分析上限定理,基于修正的Prandtl机构,推导了既可以合理反映支护结构入土深度影响,又可以反映土体强度非均质和各向异性特性的基坑抗隆起稳定的上限解公式,同时基于商业化程序的二次开发,建立了可以考虑土体强度非均质和各向异性影响的强度折减弹塑性有限元方法。通过提出的修正Prandtl机构上限解与强度折减有限元方法以及多块体上限解的对比,验证了修正机构上限解以及强度折减有限元法的合理性和可行性,最后讨论了非均质系数、各向异性系数、支护机构入土深度等因素对基坑抗隆起稳定性的影响,并通过了实例的验证,相关结论可供工程参考。     

多级支挡结构地震主动土压力的极限分析

多级组合支挡结构形式在高边坡防护工程中得到了广泛采用,但现有研究却较少涉及这种支挡结构形式的地震土压力计算问题。应用拟静力法和塑性极限分析上限定理,并且基于强度折减技术,推导了重力式挡墙与两级锚杆挡墙组合支挡结构形式的地震主动土压力及其系数的上限解。该上限解考虑了水平和竖向地震系数、墙背倾角、坡面形式及多级支护方式、土体黏聚力、土体与墙背的黏附力等诸多因素。二级锚杆挡墙实例分析表明：静力条件下主动土压力计算值与现有相关方法的计算结果一致,土的抗剪强度折减系数、上挡墙锚杆轴力等参数,对下挡墙地震主动土压力影响显著。二级组合支挡结构地震主动土压力影响参数敏感性分析表明：水平地震系数以及重力式挡墙墙高和倾角的敏感性较大,上挡墙锚杆的轴力和倾角等参数的敏感性相对较小     

根据截断的G-R模型计算东北地震区震级上限

震级上限是指一个地区可能发生地震的最大震级,其概率意义为发生超过该震级地震的概率几乎为0.在有些地区,由于对其内部的地震构造研究和认识存有局限性,很难根据构造或者地质学的原则来确定震级上限.因此,根据数学模型,采用统计手段,使用地震活动性资料来计算震级上限的估计值是一种可行的方法.本文根据截断的G-R关系模型,采用最大似然计算方法,使用东北地震区的地震目录,计算了东北地震区震级上限,结果表明东北地震区的震级上限应为M_u=7.5左右.计算中我们考虑了不同震级的转换、震级误差的修正以及计算方法的影响.最终结果表明,不论采用何种方案进行计算,东北地震区的震级上限值均始终保持在7.5左右,这说明我们采用本文中方法计算得到的东北地震区的震级上限值是合理可信的,同时也说明在以往的研究中对东北地震区震级上限的估计大都是偏小的.     

Generalized failure envelope for caisson foundations in cohesive soil: Static and dynamic loading

The response of massive caisson foundations to combined vertical (N), horizontal (Q) and moment (M) loading is investigated parametrically by a series of three-dimensional finite element analyses. The study considers foundations in cohesive soil, with due consideration to the caisson-soil contact interface conditions. The ultimate limit states are presented by failure envelopes in dimensionless and normalized forms and the effects of the embedment ratio, vertical load and interface friction on the bearing capacity are studied in detail. Particular emphasis is given on the physical and geometrical interpretation of the kinematic mechanisms that accompany failure, with respect to the loading ratio M/Q. Exploiting the numerical results, analytical expressions are derived for the capacities under pure horizontal, moment and vertical loading, for certain conditions. For the case of fully bonded interface conditions, comparison is given with upper bound limit equilibrium solutions based on Brinch Hansen theory for the ultimate lateral soil reaction. A generalized closed-form expression for the failure envelope in M–Q–N space is then proposed and validated for all cases examined. It is shown that the incremental displacement vector of the caisson at failure follows an associated flow rule, with respect to the envelope, irrespective of: (a) the caisson geometry, and (b) the interface conditions. A simplified geometrical explanation and physical interpretation of the associativity in M-Q load space is also provided. Finally, the derived failure envelope is validated against low (0.67 Hz) and high frequency (5 Hz) dynamic loading tests and the role of radiation damping on the response of the caisson at near failure conditions is unraveled.     

Active and passive arching stresses in c′-ϕ′ soils: A sensitivity study using computational limit analysis

Vertical soil arching, commonly known as the “trapdoor mechanism,” is a pervasive phenomenon in various geotechnical applications that can be evaluated through a variety of analytical and numerical approaches, most of which exist due to a variety of proposed arching mechanisms, many of which are focused on either purely frictional or cohesive soils. This study investigates the realized arching mechanisms and associated loads for trapdoors under both active and passive arching conditions in c′-ϕ′ soils through a series of dimensionless charts using both upper and lower bound limit analyses. An associated sensitivity analysis demonstrates that arching loads are highly dependent on collapse mechanism, a function of not only geometry, but soil shear strength, with cohesion affecting the realized mechanism and arching loads.     

Multi‐slicing strategy for the three‐dimensional discontinuity layout optimization (3D DLO)

Discontinuity layout optimization (DLO) is a recently presented topology optimization method for determining the critical layout of discontinuities and the associated upper bound limit load for plane two‐dimensional and three‐dimensional (3D) problems. The modelling process (pre‐processing) for DLO includes defining the discontinuities inside a specified domain and building the target function and the global constraint matrix for the optimization solver, which has great influence on the the efficiency of the computation processes and the reliability of the final results. This paper focuses on efficient and reliable pre‐processing of the discontinuities within the 3D DLO and presents a multi‐slicing strategy, which naturally avoids the overlapping and crossing of different discontinuities. Furthermore, the formulation of the 3D discontinuity considering a shape of an arbitrary convex polygon is introduced, permitting the efficient assembly of the global constraint matrix. The proposed method eliminates unnecessary discontinuities in 3D DLO, making it possible to apply 3D DLO for solving large‐scale engineering problems such as those involving landslides. Numerical examples including a footing test, a 3D landslide and a punch indentation are considered, illustrating the effectiveness of the presented method. © 2016 The Authors. International Journal for Numerical and Analytical Methods in Geomechanics published by John Wiley & Sons Ltd.     

具有随机状态转移矩阵的Kalman滤波

讨论状态转移矩阵为随机性矩阵时的Kalman滤波方法,并给出滤波的具体算法及分析滤波的收敛特性和参数的取值范围。通过实际算例证实了该滤波方法的有效性。