型钢混凝土异形柱的轴压比限值研究

利用有限元数值积分法编写了型钢混凝土(SSC)异形柱轴压比限值的计算机程序,利用该程序可以计算任意荷载角、任意配钢形式的SSC异形柱的轴压比限值.对不同配钢形式、不同配钢率、不同截面尺寸、不同混凝土强度等级、不同荷载角作用下的SSC异形柱的轴压比限值进行深入分析.得出了以下主要结论:荷载角、配钢形式、截面尺寸对轴压比限值有明显影响;合理配钢的SSC异形柱的轴压比限值比钢筋混凝土(RC)异形柱有所提高;箍筋约束混凝土作用对轴压比限值有明显提高.     

Wave barrier of lime–cement columns against train-induced ground-borne vibrations

This paper presents a comparison between measured train-induced ground vibrations in the free-field before and after countermeasures had been taken at Kåhög near Gothenburg in Sweden. A wave barrier of lime–cement columns was constructed parallel to the railway in order to reduce the ground-borne vibrations inside nearby buildings. On top of the barrier an embankment was built to reduce air-borne vibrations. Due to the wave barrier design, part of the energy content of the waves was expected to be reflected by the screen and transmitted energy was expected to be partly scattered. Contribution from the noise-embankment was not thought likely but could not be ruled out due to its fairly large mass and its close proximity to the railway. The effect of the mitigating measures resulted in a 67% reduction of the maximum particle velocity at 30 m and 41% at 60 m from the railway. A simple two-dimensional finite element model has been used to study the relative importance of the wave barrier and the noise-embankment as contributors to the mitigation recorded of the ground vibrations in the field. It is concluded with respect to ground vibrations that both the barrier and the embankment had a mitigating effect but that the contribution from the barrier dominated. Furthermore, it is seen from the field results as well as the simulation that the effect of the mitigating action is reduced with increasing distance from the railway.     

Transport and sedimentation dynamics of transitional explosive eruption columns: The example of the 800 BP Quilotoa plinian eruption (Ecuador)

Impact of large-scale explosive eruptions largely depends on the dynamics of transport, dispersal and deposition of ash by the convective system. In fully convective eruptive columns, ejected gases and particles emitted at the vent are vertically injected into the atmosphere by a narrow, buoyant column and then dispersed by atmosphere dynamics on a regional scale. In fully collapsing explosive eruptions, ash partly generated by secondary fragmentation is carried and dispersed by broad co-ignimbrite columns ascending above pyroclastic currents. In this paper, we investigate the transport and dispersion dynamics of ash and lapillis during a transitional plinian eruption in which both plinian and co-ignimbrite columns coexisted and interacted. The 800 BP eruptive cycle of Quilotoa volcano (Ecuador) produced a well-exposed tephra sequence. Our study shows that the sequence was accumulated by a variety of eruptive dynamics, ranging from early small phreatic explosions, to sustained magmatic plinian eruptions, to late phreatomagmatic explosive pulses. The eruptive style of the main 800 BP plinian eruption (U1) progressively evolved from an early fully convective column (plinian fall bed), to a late fully collapsing fountain (dense density currents) passing through an intermediate transitional eruptive phase (fall + syn-plinian dilute density currents). In the transitional U1 regime, height of the convective plinian column and volume and runout of the contemporaneous pyroclastic density currents generated by partial collapses were inversely correlated. The convective system originated from merging of co-plinian and co-surge contributions. This hybrid column dispersed a bimodal lapilli and ash-fall bed whose grain size markedly differs from that of classic fall deposits accumulated by fully convective plinian columns. Sedimentological analysis suggests that ash dispersion during transitional eruptions is affected by early aggregation of dry particle clusters.     

火灾下型钢混凝土异形柱温度场分析

为了分析型钢混凝土异形柱的耐火极限及火灾后的力学性能,为试验研究做好充分的前期准备,本文采用有限元分析软件ANSYS对型钢混凝土异形柱截面温度场进行数值模拟,得出了柱截面在不均匀受火情况下的温度场分布规律。结果表明,在两面受火的情况下,L形柱的凹角处的温升低于其它部位;由于型钢的存在,加快了柱截面内部温度的热传导;距离受火面相同的深度处的混凝土与型钢的温度不同,因此有必要研究损伤差异对承载力和两者粘结滑移造成的影响。     

Analysis of the rocking response of rigid blocks standing free on a seismically isolated base

This paper examines the rocking response and stability of rigid blocks standing free on an isolated base supported: (a) on linear viscoelastic bearings, (b) on single concave and (c) on double concave spherical sliding bearings. The investigation concludes that seismic isolation is beneficial to improve the stability only of small blocks. This happens because while seismic isolation increase the ‘static’ value of the minimum overturning acceleration, this value remains nearly constant as we move to larger blocks or higher frequency pulses; therefore, seismic isolation removes appreciably from the dynamics of rocking blocks the beneficial property of increasing stability as their size increases or as the excitation pulse period decreases. This remarkable result suggests that free‐ standing ancient classical columns exhibit superior stability as they are built (standing free on a rigid foundation) rather than if they were seismically isolated even with isolation system with long isolation periods. The study further confirms this finding by examining the seismic response of the columns from the peristyle of two ancient Greek temples when subjected to historic records. Copyright © 2011 John Wiley & Sons, Ltd.     

Tests and model calibration of high‐strength steel tubular beam‐to‐column and column‐base composite joints for moment‐resisting structures

Performance‐based engineering (PBE) methodologies allow for the design of more reliable earthquake‐resistant structures. Nonetheless, to implement PBE techniques, accurate finite element models of critical components are needed. With these objectives in mind, initially, we describe an experimental study on the seismic behaviour of both beam‐to‐column (BTC) and column‐base (CB) joints made of high‐strength steel S590 circular columns filled with concrete. These joints belonged to moment‐resisting frames (MRFs) that constituted the lateral‐force‐resisting system of an office building. BTC joints were conceived as rigid and of partial strength, whereas CB joints were designed as rigid and of full strength. Tests on a BTC joint composed of an S275 steel composite beam and high‐strength steel concrete‐filled tubes were carried out. Moreover, two seismic CB joints were tested with stiffeners welded to the base plate and anchor bolts embedded in the concrete foundation as well as where part of a column was embedded in the foundation with no stiffeners. A test programme was carried out with the aim of characterising these joints under monotonic, cyclic and random loads. Experimental results are presented by means of both force–interstory drift ratio and moment–rotation relationships. The outcomes demonstrated the adequacy of these joints to be used for MRFs of medium ductility class located in zones of moderate seismic hazard. Then, a numerical calibration of the whole joint subassemblies was successfully accomplished. Finally, non‐linear time‐history analyses performed on 2D MRFs provided useful information on the seismic behaviour of relevant MRFs. Copyright © 2015 John Wiley & Sons, Ltd.     

Modeling level selection for seismic analysis of concrete‐filled steel tube/moment‐resisting frames by using fragility curves

The seismic behavior of plane moment‐resisting frames (MRFs) consisting of I steel beams and concrete‐filled steel tube (CFT) columns is investigated in this study. More specifically, the effect of modeling details of each individual component of CFT‐MRFs, such as the composite CFT columns, the beam‐column connections, the panel zones, and the steel I beams on their seismic behavior, is studied through comparisons against available experimental results. Then, fragility curves are constructed for three typical CFT‐MRFs, designed according to European codes, for various levels of modeling sophistication through nonlinear time‐history analyses. On the basis of these fragility curves, one can select the appropriate modeling level of sophistication that can lead to the desired seismic behavior for a given seismic intensity. Copyright © 2014 John Wiley & Sons, Ltd.     

Seismic collapse risk of precast industrial buildings with strong connections

A systematic seismic risk study has been performed on some typical precast industrial buildings that consists of assemblages of cantilever columns with high shear‐span ratios connected to an essentially rigid roof system with strong pinned connections. These buildings were designed according to the requirements of Eurocode 8. The numerical models and procedures were modified in order to address the particular characteristics of the analyzed system. They were also verified by pseudo‐dynamic and cyclic tests of full‐scale large buildings. The intensity measure (IM)‐based solution strategy described in the PEER methodology was used to estimate the seismic collapse risk in terms of peak ground acceleration capacity and the probability of exceeding the global collapse limit state. The effect of the uncertainty in the model parameters on the dispersion of collapse capacity was investigated in depth. Reasonable seismic safety (as proposed by the Joint Committee on Structural Safety) was demonstrated for all the regular single‐storey precast industrial buildings addressed in this study. However, if the flexural strength required by EC8 was exactly matched, and the additional strength, which results from minimum longitudinal reinforcement, was disregarded as well as large dispersion in records was considered, the seismic risk might in some cases exceed the acceptable limits. Copyright © 2009 John Wiley & Sons, Ltd.     

Information for Contributors

Journal of Meteorological Research is an international academic journal in atmospheric sciences edited and published by Acta Meteorologica Sinica Press, sponsored by the Chinese Meteorological Society. It has been acting as a bridge of academic exchange between Chinese and foreign meteorologists and aiming at introduction of the current advancements in atmospheric sciences in China. The journal columns include Articles, Note and Correspondence, and research letters. Contributions from all over the world are welcome.