考虑钙质砂细观颗粒形状影响的液体拖曳力系数试验

钙质砂作为南海岛礁填筑常用的岩土材料,其渗透性很大程度上决定着填筑后土体的固结和沉降。拖曳力系数是表达流体对土体颗粒表面力的参数,也是表征颗粒状土体渗透能力的一个重要参数,目前国内外对钙质砂拖曳力系数的研究十分有限。首先引入一个修正的三维参数 对钙质砂这种天然非规则颗粒材料的形状进行定量描述,然后开展一系列单个钙质砂颗粒在液体中沉降试验,利用高速相机记录颗粒沉降过程,结合图像处理技术获得颗粒沉降平衡速度Ut,进而计算出拖曳力系数CD和雷诺数Re,最后拟合出包含CD、Re及 三个参数的钙质砂拖曳力系数半经验模型。结果发现,在相同雷诺数条件下钙质砂的形状系数 越大,拖曳力系数越小。通过与其他研究结果对比发现,其表面微孔隙越发育,拖曳力系数越小的规律。该模型能够考虑不规则颗粒形状对拖曳力系数的影响,从而提高对土体渗透性预测的精度,对南海岛礁填筑工程中钙质砂固结和沉降的计算也具有重要意义。     

Experimental analysis on the risk of vortex ventilation and the free surface ventilation of marine propellers

The paper presents a discussion of the ventilation inception and air drawing prediction of ships propellers, aiming to predict under what conditions ventilation will happen, and the actual physical mechanism of the ventilation.Three different types of ventilation inception mechanisms are included in our discussion: free surface vortex ventilation, ventilation by sucking down the free surface without forming a vortex as well as ventilation by propeller coming out of the water. Ventilation prediction is based on a series of model tests, where the propeller is tested in different levels of intermittent ventilation. The use of underwater video gives a visual understanding of the ventilation phenomena.Ventilation by vortex formation has analogies with other phenomena, such as the inlet vortex in pump sumps, ground vortex at the inlet of the aircraft engines and the Propeller Hull Vortex Cavitation (PHVC). The paper includes comparison between Propeller Hull Vortex Cavitation (PHVC) and Propeller Free Surface Vortex Ventilation (PFSVV) as well as comparison between PFSVV and vortex formations of aero engines during high power operation near a solid surface.Experimental data based on several different model tests shows the boundary between the vortex forming, non-vortex forming and free surface ventilation flow regimes. For comparison the following parameters, which determined the intensity of the hydrodynamic interaction between the propeller and free surface have been used: propeller load coefficient c_T, tip clearance ratio c/D, propeller submergence ratio h/R, ambient velocity V_i and flow cavitation/ventilation number σ_cav/σ_vent.     

Numerical simulations of a highway bridge structure employing passive negative stiffness device for seismic protection

A new passive seismic response control device has been developed, fabricated, and tested by the authors and shown to be capable of producing negative stiffness via a purely mechanical mechanism, thus representing a new generation of seismic protection devices. Although the concept of negative stiffness may appear to be a reversal on the desired relationship between the force and displacement in structures (the desired relationship being that the product of restoring force and displacement is nonnegative), when implemented in parallel with a structure having positive stiffness, the combined system appears to have substantially reduced stiffness while remaining stable. Thus, there is an ‘apparent weakening and softening’ of the structure that results in reduced forces and increased displacements (where the weakening and softening is of a non‐damaging nature in that it occurs in a seismic protection device rather than within the structural framing system). Any excessive displacement response can then be limited by incorporating a damping device in parallel with the negative stiffness device. The combination of negative stiffness and passive damping provides a large degree of control over the expected performance of the structure. In this paper, a numerical study is presented on the performance of a seismically isolated highway bridge model that is subjected to various strong earthquake ground motions. The Negative Stiffness Devices (NSDs) are described along with their hysteretic behavior as obtained from a series of cyclic tests wherein the tests were conducted using a modified design of the NSDs (modified for testing within the bridge model). Using the results from the cyclic tests, numerical simulations of the seismic response of the isolated bridge model were conducted for various configurations (with/without negative stiffness devices and/or viscous dampers). The results demonstrate that the addition of negative stiffness devices reduces the base shear substantially, while the deck displacement is limited to acceptable values. This assessment was conducted as part of a NEES (Network for Earthquake Engineering Simulation) project which included shaking table tests of a quarter‐scale highway bridge model. Copyright © 2014 John Wiley & Sons, Ltd.     

Mass rig system for shaking table tests of slender columns

A new mass rig system is proposed to minimize the deficiencies in current shaking table testing setups. This is accomplished by placing the inertial mass on a convex path designed to impose P‐Delta demands on slender cantilever columns. The design and performance of the mass rig system, and the principles used in deriving the equations of motion and their analytical validation against results obtained from shaking table tests, are presented. Formulation of the governing equations of motion was based on Lagrangian mechanics and solved using an implicit linear acceleration method with an adaptive time step formulation. Friction developed in the sliding system was also incorporated in the equations of motion. Experimental results validated the accuracy in the derivation and solution of the equations of motion. Validated by analytical and experimental results, P‐Delta effects were found to increase the displacement demands on slender columns in the low‐frequency range of acceleration input, while in the high‐frequency range P‐Delta effects led to no increase and in some cases even a reduction in displacement demands. Copyright © 2015 John Wiley & Sons, Ltd.     

松软煤层井下泡沫钻进工艺试验

松软煤层瓦斯抽采孔的深孔施工技术在现有的钻进工艺下不能很好的满足要求。为了提高松软煤层钻进的时效和孔深,提出了煤矿井下松软煤层泡沫钻进工艺,并在淮北邹庄矿进行了现场试验。分析了3个试验孔的具体工况,提出了较为合理的解决方法,使钻孔深度达到了200 m。这不仅有效增加了在松软煤层中的成孔深度,提高了成孔率,还降低了孔口的粉尘污染。      

Implications of geomorphological research for recent and prehistoric avalanches and related hazards at Huascaran,Peru

Detailed research of superficial deposits below the northern peak of Huascaran (Cordillera Blanca) provides new information on the limits of a paleo-avalanche originating from this mountain. Geomorphological mapping of the sediments identified glacial deposits, deposits from historical rock-debris avalanches and huge boulders from a paleo-avalanche. Schmidt Hammer rock-hardness tests were used to distinguish between the several generations of rock-debris avalanches, but largely failed to distinguish between the much older moraine and the paleo-avalanche sediments. Thus, only the field geomorphological mapping proved to be reliable for identifying the limits of the paleo-avalanche. The limits identified as granite boulders deposited over volcanic rocks were found to extend 30 m further up the opposite valley slope than previously had been mapped. This larger extent implies a greater volume and/or greater mobility for the prehistoric event.     

Air-floating towing behaviors of multi-bucket foundation platform

Air-floating towing beha viors of multi-bucket foundation plat form （MBFP） are investigated with the 1/20-scale model tests and hydrodynamic so ftware MOSES. MOSES numerical model was val idated by test results, and M OSES prototype model of MBFP can eliminate scale effect of model. The influences of towing factors of to wing speed, water depth, freeboard, and w ave direction on air-floating tow ing stability of MBFP were analyzed by model tests and validated MOSES prototype mod el. It is sho wn that the re duction of towing sp eed can effectively d ecrease the to wing force and surge acceleration to improve towing stability. Water depth is another f actor in towing s tability. Obvious shallow water effect will appear in shallow water with sma ll water depth-draft ratio and it w ill disappear gradually and air-floating towing becomes more stable with the increase of water depth. Accelerations of surge, s way and heave are small and they have modest changes when freeboard increases from 0.5 to 2 m. For MBFP, the freeboard is not suggested to be larger than 2 m in following wave. Wave direction has large influence on the towing stability, the surge acceleration and towing force are sensitive to the va riation of wave direction, the surge acceleration and towing force in following wave （0°） and counter wave （180°） are much larger than that in transverse sea （90°and 270°）.     

TJ-1模拟月壤承载特性的现场试验研究

采用TJ-1模拟月壤作为试验材料,通过静力触探、静载荷试验的对比分析,探讨适合月壤承载力计算的经验公式,以期为未来载人登月时宇航员和着陆器登陆可能涉及到有关月面承载能力的问题提供必要的参考。首先,使用近255 t TJ-1模拟月壤人工制备出13 m×12 m×1.2 m试验用地基,后在试验地基均匀布置6个静力触探测点和2个静载荷试验测点进行测试。针对太沙基承载力计算半经验公式以及规范和国内外学者提出的12个适合中密实砂土静力触探承载力计算的经验公式,对试验结果进行探讨。发现直接运用太沙基提出的半经验公式计算月壤承载力结果明显偏小,而由联合试验小组提出的经验公式 能够用来近似计算月壤地基承载力。计算结果表明,该经验公式在计算承载力时能够与静载荷试验值较好的吻合。     

Dynamic response and optimal design of structures with large mass ratio TMD

This paper investigates the dynamic behavior and the seismic effectiveness of a non‐conventional Tuned Mass Damper (TMD) with large mass ratio. Compared with conventional TMD, the device mass is increased up to be comparable with the mass of the structure to be protected, aiming at a better control performance. In order to avoid the introduction of an excessive additional weight, masses already present on the structure are converted into tuned masses, retaining structural or architectural functions beyond the mere control function. A reduced order model is introduced for design purposes and the optimal design of a large mass ratio TMD for seismic applications is then formulated. The design method is specifically developed to implement High‐Damping Rubber Bearings (HDRB) to connect the device mass to the main structure, taking advantage of combining stiffness and noticeable damping characteristics. Ground acceleration is modeled as a Gaussian random process with white noise power spectral density. A numerical searching technique is used to obtain the optimal design parameter, the frequency ratio alpha, which minimizes the root‐mean‐square displacement response of the main structure. The study finally comprises shaking table tests on a 1:5 scale model under a wide selection of accelerograms, both artificial and natural, to assess the seismic effectiveness of the proposed large mass ratio TMD. Copyright © 2011 John Wiley & Sons, Ltd.     

Fragility analysis of low‐rise masonry in‐filled reinforced concrete buildings by a coefficient‐based spectral acceleration method

This study presents a seismic fragility analysis of low‐rise masonry in‐filled (MI) reinforced concrete (RC) buildings using a proposed coefficient‐based spectral acceleration method. The coefficient‐based method, without requiring any complicated finite element analysis, is a simplified procedure for assessing the spectral acceleration demand (or capacity) of buildings subjected to earthquakes. This paper begins with a calibration of the proposed coefficient‐based method for low‐rise MI RC buildings using published experimental results obtained from shaking table tests. Spectral acceleration‐based fragility curves for low‐rise MI RC buildings under various inter‐story drift limits are then constructed using the calibrated coefficient‐based method. A comparison of the experimental and estimated results indicates that the simplified coefficient‐based method can provide good approximations of the spectral accelerations at peak loads of low‐rise MI RC buildings, if a proper set of drift‐related factors and initial fundamental periods of structures are used. Moreover, the fragility curves constructed using the coefficient‐based method can provide a satisfactory vulnerability evaluation for low‐rise MI RC buildings under a given performance level. Copyright © 2011 John Wiley & Sons, Ltd.