福建沿海剪切波速与土层参数定量关系研究

通过对大量实测数据的分析，按照剪切波速与土层密度、标贯击数、土层埋深之间的关系特征，利用单因子及多因子回归分析方法，给出剪切波速与土层密度、标贯击数、土层埋深的定量关系。     

剪切和摩擦滑动大模型的视电阻率变化幅度和各向异性

用石英砂、河砂和水泥模压制成1m×1m×0.3m的均匀和非均匀介质模型，对模型进行剪切和摩擦滑动实验，观测模型不同位置和不同方位的视电阻率变化幅度和各向异性特征. 均匀介质模型实验结果为：电阻率变化与测线的位置有关，距裂隙近的测线，电阻率变化幅度大，从百分之几到百分之几十；距裂隙远的测线，电阻率变化幅度小，从百分之几到不变. 对于非均匀介质模型，电阻率变化幅度要小一些，最大也只有百分之几. 电阻率变化除与测线的位置有关外，还与测线的方位有关，同一测点不同方位的测线，电阻率变化幅度不同，有的差别很大. 剪切与摩擦滑动两种加载方式的电阻率变化幅度数量级相同. 裂隙穿过部位及其附近测点的电阻率变化各向异性主轴方位解与剪切和摩擦滑动的实际裂隙方位吻合较好.     

软弱夹层特性对地震波强度影响的模拟研究

模拟了隐伏软弱夹层的弹塑性参数对其地震波放大效应的影响,发现当软弱层波速不大于上下围岩的 30 %时,就会在特定的频率上产生相当显著的地震动放大作用。研究结果表明,夹层放大作用的强度主要与其波速有关,而与密度及品质因素关系不大。研究还发现,这种放大作用的强度受软弱层波速与厚度之间的某种关系制约。这种关系的规律尚待通过进一步的理论分析或大量模拟研究去揭示。     

Slip sense inversion on active strike-slip faults in southwest Japan and its implications for Cenozoic tectonic evolution

Analyses of deflected river channels, offset of basement rocks, and fault rock structures reveal that slip sense inversion occurred on major active strike-slip faults in southwest Japan such as the Yamasaki and Mitoke fault zones and the Median Tectonic Line (MTL). Along the Yamasaki and Mitoke fault zones, small-size rivers cutting shallowly mountain slopes and Quaternary terraces have been deflected sinistrally, whereas large-size rivers which deeply incised into the Mio-Pliocene elevated peneplains show no systematically sinistral offset or complicated hairpin-shaped deflection. When the sinistral offsets accumulated on the small-size rivers are restored, the large-size rivers show residual dextral deflections. This dextral offset sense is consistent with that recorded in the pre-Cenozoic basement rocks. S–C fabrics of fault gouge and breccia zone developed in the active fault zones show sinistral shear sense compatible with earthquake focal mechanisms, whereas those of the foliated cataclasite indicate a dextral shear sense. These observations show that the sinistral strike-slip shear fabrics were overprinted on dextral ones which formed during a previous deformation phase. Similar topographic and geologic features are observed along the MTL in the central-eastern part of the Kii Peninsula. Based on these geomorphological and geological data, we infer that the slip sense inversion occurred in the period between the late Tertiary and mid-Quaternary period. This strike-slip inversion might result from the plate rearrangement consequent to the mid-Miocene Japan Sea opening event. This multidisciplinary study gives insight into how active strike-slip fault might evolves with time.     

Deformation conditions, kinematics, and displacement history of shallow crustal ductile shearing in the Norumbega fault system in the Northern Appalachians, eastern Maine

The Norumbega fault system in the Northern Appalachians in eastern Maine experienced complex post-Acadian ductile and brittle deformation from middle through late Paleozoic times. Well-preserved epizonal ductile shear zones in Fredericton belt metasedimentary rocks and granitic batholiths that intrude them provide valuable information on the nature, geometry, and evolution of orogen-parallel strike-slip Norumbega faulting. Metasedimentary rocks were ductilely sheared into phyllonite schistose mylonite, whereas granite into mylonite within the ductile shear zones. Ductile shearing took place at conditions of the lower greenschist facies with peak temperatures on the order of 300–350° based on comparison of plastic quartz and brittle feldspar microstructures, confirming a shallow crustal environment during faulting.Ductile shear strain was partitioned into two major shear zones in easternmost Maine—the Waite and Kellyland zones—but these zones converge toward the southwest. Megascopic, mesoscopic, and microscopic kinematic indicators confirm that fault motion in both zones was dominantly dextral strike-slip. Detailed mapping, especially in the plutonic rocks, reveals a complex ductile deformation history in the area where the Waite and Kellyland zones converge. Shear strain is broadly distributed in the rocks between Kellyland and Waite zones, and increases toward their junction. Multiple dextral high-strain zones oblique to both zones resemble megascopic synthetic c′ shear bands. Together with the Kellyland and Waite master shear zones, these define a megascopic S–C′ structure system produced in a regional-scale dextral strike-slip shear duplex that developed in the transition zone between the deeper (south-central Maine) and shallower (eastern Maine) segments of the Norumbega fault system.Granite plutons caught within the strike-slip shear duplex were intensely sheared and progressively smeared into long and narrow slivers identified by this study. The western lobe of the Deblois pluton and the Lucerne pluton have been recognized as the sources, respectively of the Third Lake Ridge and Morrison Ridge granite slivers. Restoration of both granite slivers to their presumed original positions yields approximately 25 km of dextral strike-slip displacement along only the Kellyland and synthetic ductile shear zones.     

Strength of moist sand controlled by surface tension for tectonic analogue modelling

A technique has been developed to control the strength of moistened sand in a quantifiable, accurate and reproducible way, while other mechanical properties were maintained. Strength of dry sand was increased through adding a small amount of liquid. In order to control the additional cohesion of moist sand, the influence of the surface tension of the liquid was investigated. Direct shear experiments were performed on four granular materials at confining stress levels below 1 kPa. It has been found that the surface tension of the added liquid controlled the additional apparent cohesion of sand with high accuracy. The mechanical properties of moist sand show dynamic similarity towards natural brittle rock, which enables analogue modelling of fault formation, fault reactivation and tension fracture formation in the brittle regime with a controlled strength profile. Furthermore, experimental results fit well to shear strength models. From this followed the direct proportionality of the unsaturated shear strength parameter φ^b relative to the matrix suction, measured at low stress levels. Moreover, shear strength turned out to be also a function of grain size and the grain shape.     

Mapping upper mantle anisotropy beneath SE France by SKS splitting indicates Neogene asthenospheric flow induced by Apenninic slab roll-back and deflected by the deep Alpine roots

The presence of two regional seismic networks in southeastern France provides us high-quality data to investigate upper mantle flow by measuring the splitting of teleseismic shear waves induced by seismic anisotropy. The 10 three-component and broadband stations installed in Corsica, Provence, and western Alps efficiently complete the geographic coverage of anisotropy measurements performed in southern France using temporary experiments deployed on geodynamic targets such as the Pyrenees and the Massif Central. Teleseismic shear waves (mainly SKS and SKKS) are used to determine the splitting parameters: the fast polarization direction and the delay time. Delay times ranging between 1.0 and 1.5 s have been observed at most sites, but some larger delay times, above 2.0 s, have been observed at some stations, such as in northern Alps or Corsica, suggesting the presence of high strain zones in the upper mantle. The azimuths of the fast split shear waves define a simple and smooth pattern, trending homogeneously WNW–ESE in the Nice area and progressively rotating to NW–SE and to NS for stations located further North in the Alps. This pattern is in continuity with the measurements performed in the southern Massif Central and could be related to a large asthenospheric flow induced by the rotation of the Corsica–Sardinia lithospheric block and the retreat of the Apenninic slab. We show that seismic anisotropy nicely maps the route of the slab from the initial rifting phase along the Gulf of Lion (30–22 Ma) to the drifting of the Corsica–Sardinia lithospheric block accompanied by the creation of new oceanic lithosphere in the Liguro–Provençal basin (22–17 Ma). In the external and internal Alps, the pattern of the azimuth of the fast split waves follows the bend of the alpine arc. We propose that the mantle flow beneath this area could be influenced or perhaps controlled by the Alpine deep penetrative structures and that the Alpine lithospheric roots may have deflected part of the horizontal asthenospheric flow around its southernmost tip.     

鄂西高速公路岩体结构面强度参数试验研究

对湖北省西部某高速公路宜昌—恩施段主要岩体结构面(层面)的抗剪强度参数进行了较系统的试验研究,包括岩体结构面的野外地质调查、岩体结构面原位直剪试验、结构面室内模拟试验及岩体力学参数估值等。通过对各种试验数据进行整理、分析和对比,得到了岩体结构面强度参数。最后在岩体工程分类的基础上,利用Hoek-Brown经验方法对各类岩体结构面强度参数进行了估算。综合以上多种数据,并考虑岩体结构面所处具体地质条件,提出了各类岩体结构面强度参数建议值。     

Microstructural study of a natural slip zone: quantification and deformation history

Microstructure of a natural slip zone was comprehensively examined using a combination of images captured systematically by optical microscopy (OPM) and backscattered electron microscopy (BEM) techniques. Microstructural features identified on these images were processed and evaluated using an advanced image analysis system, which proved that quantitative analyses could considerably enhance the understanding of shear behavior of slip zones. It was found that variations of porosity, abundance of platy clay particles and alignments of particles are significant indicators revealing nature of deformation processes. These indicators show that global mechanical behavior of the investigated slip zone can be conceptualized as that of normally consolidated clayey soils under drained conditions.

The geometric patterns of the microstructure of the slip zone are similar to the S–C fabrics seen in tectonic shear zones. It is suggested that combined progressive bulk simple shear and pure shear modes enable to realistically reconstruct the kinematic history of the slip zone, through which particle movements and microstructural evolution were accomplished via various types of particulate flows. The results of this study show that clay mineralogy plays a more important role in the development of the slip zone than abundance of clay-size particles, while both clay mineralogy and relative proportions of each particle size fraction control the response of particles to shear deformation. Among the fractions present in the slip zone, fine silts are the strongest indicator of global shear stress characterized by their highest degree of alignment, whereas clay particles are the weakest. Highest degree of shape preferred orientation is also found within fine silt domains.     

Kinematic reworking and exhumation within the convergent Alpine Orogen

Kinematic data from the internal zones of the Western Alps indicate both top-to-SE and top-to-NW shearing during synkinematic greenschist facies recrystallisation. Rb/Sr data from white micas from different kinematic domains record a range of ages that does not represent closure through a single thermal event but reflects the variable timing of synkinematic mica recrystallisation at temperatures between 300 and 450 °C. The data indicate an initial phase of accretion and foreland-directed thrusting at ca. 60 Ma followed by almost complete reworking of thrust-related deformation by SE-directed shearing. This deformation is localised within oceanic units of the Combin Zone and the base of the overlying Austroalpine basement, and forms a regional scale shear zone that can be traced for almost 50 km perpendicular to strike. The timing of deformation in this shear zone spans 9 Ma from 45 to 36 Ma. The SE-directed shear leads to local structures that cut upwards in the transport direction with respect to tectonic stratigraphy, and such structures have been interpreted in the past as backthrusts in response to ongoing Alpine convergence. However, on a regional scale, the top-to-SE deformation is related to crustal extension, not shortening, and is coincident with exhumation of eclogites in its footwall. During this extension phase, deformation within the shear zone migrated both spatially and temporally giving rise to domains of older shear zone fabrics intercalated with zones of localised reworking. Top-NW kinematics preserved within the Combin Zone show a range of ages. The oldest (48 Ma) may reflect the final stages of emplacement of Austroalpine Units above Piemonte oceanic rocks prior to the onset of extension. However, much of the top-to-NW deformation took place over the period of extension and may reflect either continuing or episodic convergence or tectonic thinning of the shear zone.⁴⁰Ar/³⁹Ar data from the region are complicated due to the widespread occurrence of excess ⁴⁰Ar in eclogite facies micas and partial Ar loss during Alpine heating. Reliable ages from both eclogite and greenschist facies micas indicate cooling ages in different tectonic units of between 32 and 40 Ma. These ages are slightly younger than Rb/Sr deformation ages and suggest that cooling below ca. 350 °C occurred after juxtaposition of the units by SE-directed extensional deformation.Our data indicate a complex kinematic history involving both crustal shortening and extension within the internal zones of the Alpine Orogen. To constrain the palaeogeographic and geodynamic evolution of the Alps requires that these data be integrated with data from the more external zones of the orogen. Complexity such as that described is unlikely to be restricted to the Western Alps and spatially and temporally variable kinematic data are probably the norm in convergent orogens. Recognising such features is fundamental to the correct tectonic interpretation of both modern and ancient orogens.