Evaluation of three waterborne polymers as stabilizers for sandy soil

This study reports on waterborne polymer emulsion systems that were used for structural modification of sandy soils. The first emulsion used was a styrene-acrylic, copolymer emulsion; the second and third were vinyl-acrylic, copolymer-based emulsions. Specimens were prepared by adding different polymer emulsions to the sand and water in prescribed amounts. The performance of the different emulsion systems as sand stabilizers was estimated through measurement of the hydraulic conductivity and compressive strength. Measurements of hydraulic conductivity were conducted in a flexible membrane test apparatus. The hydraulic conductivity for the three emulsions decreased at different rates, with an increase in polymer content up to 3 wt. (i.e., % by weight). Additional increase of polymer content did not introduce significant decrease in hydraulic conductivity, and, at 5 wt.%, the three emulsions had essentially the same effect. Measurements made on dry cylindrical specimens disclosed remarkable enhancement in the mechanical behavior of the system. The compressive strength and modulus of elasticity of the examined emulsions increased with a higher concentration of polymer. Scanning electron microscope (SEM) revealed that the reduction in the permeability and the improved mechanical properties can be attributed to three dominant structural changes: the development of interconnecting ties between the sand particles, the development of adhesion between neighboring sand particles in contact, and the covering of the sand particles with a thin polymer film.     

基于粗糙集的K--均值聚类算法在遥感影像分割中的应用

结合粗糙集理论和K——均值聚类算法，提出一种遥感影像的粗糙聚类分割方法。根据遥感影像中特征属性的相互依赖关系，应用粗糙集理论的等价关系。求出K——均值聚类所需要的初始类的个数和均值。然后采用聚类算法对图像进行分割。实验结果表明该方法比随机选取聚类的中心点和个数减少了运算量．提高了分类精度和准确性。     

Groundwater-flow modeling in the Yucatan karstic aquifer, Mexico

The current conceptual model of the unconfined karstic aquifer in the Yucatan Peninsula, Mexico, is that a fresh-water lens floats above denser saline water that penetrates more than 40 km inland. The transmissivity of the aquifer is very high so the hydraulic gradient is very low, ranging from 7–10 mm/km through most of the northern part of the peninsula. The computer modeling program AQUIFER was used to investigate the regional groundwater flow in the aquifer. The karstified zone was modeled using the assumption that it acts hydraulically similar to a granular, porous medium. As part of the calibration, the following hypotheses were tested: (1) karstic features play an important role in the groundwater-flow system; (2) a ring or belt of sinkholes in the area is a manifestation of a zone of high transmissivity that facilitates the channeling of groundwater toward the Gulf of Mexico; and (3) the geologic features in the southern part of Yucatan influence the groundwater-flow system. The model shows that the Sierrita de Ticul fault, in the southwestern part of the study area, acts as a flow barrier and head values decline toward the northeast. The modeling also shows that the regional flow-system dynamics have not been altered despite the large number of pumping wells because the volume of water pumped is small compared with the volume of recharge, and the well-developed karst system of the region has a very high hydraulic conductivity. Electronic Publication     

An automated strategy for calculation of phase diagram sections and retrieval of rock properties as a function of physical conditions

We formulate an algorithm for the calculation of stable phase relations of a system with constrained bulk composition as a function of its environmental variables. The basis of this algorithm is the approximate representation of the free energy composition surfaces of solution phases by inscribed polyhedra. This representation leads to discretization of high variance phase fields into a continuous mesh of smaller polygonal fields within which the composition and physical properties of the phases are uniquely determined. The resulting phase diagram sections are useful for understanding the phase relations of complex metamorphic systems and for applications in which it is necessary to establish the variations in rock properties such as density, seismic velocities and volatile‐content through a metamorphic cycle. The algorithm has been implemented within a computer program that is general with respect to both the choice of variables and the number of components and phases possible in a system, and is independent of the structure of the equations of state used to describe the phases of the system.     

Physical properties of ultrahigh-pressure metamorphic rocks from the Sulu terrain, eastern central China: implications for the seismic structure at the Donghai (CCSD) drilling site

About 30 samples representing major lithologies of Sulu ultrahigh-pressure (UHP) metamorphic rocks were collected from surface exposures and exploration wells, and compressional (Vp) and shear wave (Vs) velocities and their directional dependence (anisotropy) were determined over a range of constant confining pressures up to 600 MPa and temperatures ranging from 20 to 600 °C. Samples range in composition from acidic to ultramafic. P- and S-wave velocities measured at 600 MPa vary from 5.08 to 8.64 km/s and 2.34 to 4.93 km/s, respectively. Densities are in the range from 2.60 to 3.68 g/cm³. To make a direct tie between seismic measurements (refraction and reflection) and subsurface lithologies, the experimental velocity data (corresponding to shallow depths) were used to calculate velocity profiles for the different lithologies and profiles of reflection coefficients at possible lithologic interfaces across the projected 5000-m Chinese Continental Scientific Drilling Program (CCSD) crustal segment. Comparison of calculated in situ velocities with respective intrinsic velocities suggests that the in situ velocities at shallow depths are lowered by an increased abundance of open microcracks. The strongly reflective zone beneath the Donghai drill site can be explained by the impedance contrasts between the different lithologies. Contacts between eclogite/peridotite and felsic rocks (gt-gneiss, granitic gneiss), in particular, may give rise to strong seismic reflections. In addition, shear-induced (lattice preferred orientation (LPO)-related) seismic anisotropy can increase reflectivity. For the explanation of the high velocity bodies (>6.4 km/s) around 1000 m and below 3200-m depth, large proportions of eclogite/peridotite (about 40 and 30 vol.%, respectively) are needed.     

Al hematites prepared by homogeneous precipitation of oxinates: material characterization and determination of the Morin transition

A novel method for synthesis of aluminium hematites, based upon the homogeneous precipitation of Fe and Al oxinates in various proportions, is presented. The precursor precipitates are heated in air at 700?°C. X-ray diffraction, thermal analyses, BET, FTIR, optical reflection analysis, TEM and Mössbauer spectroscopy at room temperature and 80?K of the resulting products indicate that single-phase hematites are formed with structural Al substitution of up to 10 at%. Interestingly, the particle size (>100?nm) is not substantially reduced by the Al content. Although it remains difficult to obtain a homogeneously distributed Al substitution in the final hematite, this processing line offers a unique opportunity to separate the effects of grain size and Al substitution on the Morin transition temperature (T _M) of Al hematite. From the comparison between the present hematites and a series of Al-substituted hematites with lepidocrocite as precursor, it could be shown that the effect on T _M, associated with a change of a factor 10 in grain size, is about 1/3 of the effect caused by a change of 10 in the degree of substitution. Finally, it is suggested that proper thermal treatments under different conditions of the same precursors are likely to produce spinel phases.     

Development of site-specific design ground motions in Western and Eastern North America

This paper presents results recently obtained for generating site-specific ground motions needed for design of critical facilities. The general approach followed in developing these ground motions using either deterministic or probabilistic criteria is specification of motions for rock outcrop or very firm soil conditions followed by adjustments for site-specific conditions. Central issues in this process include development of appropriate attenuation relations and their uncertainties, differences in expected motions between Western and Eastern North America, and incorporation of site-specific adjustments that maintain the same hazard level as the control motions, while incorporating uncertainties in local dynamic material properties. For tectonically active regions, such as the Western United States (WUS), sufficient strong motion data exist to constrain empirical attenuation relations for M up to about 7 and for distances greater than about 10–15 km. Motions for larger magnitudes and closer distances are largely driven by extrapolations of empirical relations and uncertainties need to be substantially increased for these cases.

For the Eastern United States (CEUS), due to the paucity of strong motion data for cratonic regions worldwide, estimation of strong ground motions for engineering design is based entirely on calibrated models. The models are usually calibrated and validated in the WUS where sufficient strong motion data are available and then recalibrated for applications to the CEUS. Recalibration generally entails revising parameters based on available CEUS ground motion data as well as indirect inferences through intensity observations. Known differences in model parameters such as crustal structure between WUS and CEUS are generally accommodated as well. These procedures are examined and discussed.     

西藏自治区的土壤理化特性探讨

通过对西藏自治区主要土壤类型的实地踏勘和采样分析,并结合全国土壤普查资料的结果进行分析,揭示了本区土壤具有4点特性:即多砾石性、砂质性、成土幼年性和低矿化的富有机质性。因此,在改良本区土壤时,应重视去石与防治沙漠化措施,加强矿质养分肥料的施用,稳定有机肥的投入。     

覆盖区地球化学异常特征及甄别方法探讨

覆盖区地球化学异常是由自然和人为因素引起的，在土壤垂直剖面上元素有多种分布类型，它反映了元素在土壤中迁移、演化及人为干扰的分布特征；通过对自然和人为污染的地球化学异常源追踪和评价，为环境污染治理和地区经济可持续发展提供决策依据。     

土壤水力性质确定方法研究进展

介绍了确定土壤水力性质的各种直接方法(包括实验室方法和田间方法两大类)和间接方法如土壤转换函数方法、分形方法、形态学方法、数值反演方法和经验公式法等的研究进展和现状,指出了它们各自的优点和存在的不足.认为要不断地引入新的实验技术和改进测定设备,并把估计土壤水力性质的各种理论方法及实验信息有机地结合起来进行综合研究,以扩大它们的适用范围和提高预测精度.