基于声纳图像纹理特征的海底底质分类方法研究

一般不同底质的海底声纳图的纹理特征不同。重点分析了不同底质声纳图像纹理特征的差异,为底质分类的实现提供了基础。并提取了海底声纳图像的灰度共生矩阵,将灰度共生矩阵的统计特征作为特征向量。最后应用自组织迭代(ISODATA)分类算法依据对特征向量进行分类,从而实现了海底底质的划分。     

基于高分二号卫星数据的农作物分类方法研究

针对目前高分二号卫星数据(GF-2)有较高的空间分辨率而在农业领域应用较少和农作物分类普遍存在"同谱异物"和"同物异谱"的现象,以辽宁省沈阳市苏家屯区以西的新开河村周边为试验基地,利用最佳波段组合指数法(OIF)对所选取的高分二号(GF-2)卫星数据的纹理特征和植被指数以及波段信息进行筛选,选取最佳的波段组合,以增加分类信息、减少数据冗余。最后,针对筛选后的数据,使用最大似然法进行分类,得到农作物的分类结果。结果表明,利用该方法对农作物进行分类,分类精度得到了一定程度的提高,为目前大规模农作物种植面积的精确、迅速统计提供了一套可行的方案。     

真空预压法加固吹填土的孔隙水压力试验研究

利用真空预压法处理吹填土时,孔隙水压力变化常常反映土体固结程度的好坏。通过6个模型箱试验,监测不同排水系统下孔隙水压力变化,确定有效排水体间距。研究发现0.4m间距的土内孔压下降效果比0.8m间距的土内孔压下降效果好;排水体内的孔隙水压力与排水体类型有关,且距离排水体10 cm处土体内的孔隙水压力仅为排水体内孔隙水压力的1/2弱;滤膜排水系统中的吹填土孔隙水压力下降幅度最快,B型排水板系统次之,而砂井系统最慢。另外,对于吹填土而言,排水体有效间距介于0.4m与0.8m之间,其中滤膜的有效间距最大,B型排水板次之,砂井远小于前两者。     

安徽峙门口铜—铁—金—硫矿床地球化学特征

峙门口铜—铁—金—硫矿床发育上部层状矿体和下部脉状矿体。上部层状矿石重晶石的δ~(34)S值为+14.10‰～+18.90‰。上部层状矿石黄铁矿和方铅矿的δ~(34)S值为+3.50‰～+5.84‰,下部脉状矿石黄铁矿的δ~(34)S值为+4.80‰～+6.80‰。下部脉状矿石中脉石英的δ~(18)O值为+14.3‰～+1 8.5‰,δ~(30)Si值为-0.3%0～-0.2‰。下部脉状矿石黄铁矿Re/Os比值为78.342～175.540,上(顶)部层状矿石中黄铁矿Re/Os比值为62.298～169.545。从下部脉状矿石到上部层状矿石,δ~(34)S值、Re/Os比值和流体包裹体温度249 ℃→97 ℃逐渐降低,~(206)Pb/~(204)Pb、~(207)Pb/~(204)Pb、~(208)Pb/~(204)Pb平均值和Os_总、Re、~(187)Re等含量逐渐增高。矿石黄铁矿Re-Os同位素等时线年龄303±33 Ma。地质地球化学特征反映峙门口铜—铁—金—硫矿床为海底热水喷流沉积成因。     

埋藏环境白云石结构类型

近年来我国在白云岩储层油气勘探方面取得了重大进展,这些白云岩储层绝大多数为埋藏阶段形成的白云岩,同时大量研究也证实地层中大部分白云岩形成于埋藏环境。国际学术界对埋藏环境白云石的成因结构分类比较细致,但在我国这方面的研究还不够深入,因此本文借助国际上对埋藏环境白云石成因结构的分类方法,并结合中国白云岩研究的实际情况尝试提出埋藏环境白云石结构分类方案。该方案首先以白云石在岩石中的产状分为基质白云石和胶结白云石两大类,再以晶粒大小、晶型、晶面特征、接触关系为分类依据,将埋藏环境白云石分为六种结构类型。     

The role of diagenesis and depositional facies on pore system evolution in a Triassic outcrop analogue (SE Spain)

This study aims at unravelling the diagenetic history and its effect on the pore system evolution of the Triassic redbeds exposed in SE Spain (TIBEM¹), an outcrop analogue of the TAGI (Trias Argilo-Gréseux Inférieur) reservoir (Berkine-Ghadames Basin, Algeria). Similar climatic, base level and tectonic conditions of aforementioned alluvial formations developed analogue fluvial facies stacking patterns. Furthermore, interplay of similar detrital composition and depositional facies in both formations resulted in analogue early diagenetic features. Petrographic observations indicate lithic subarkosic (floodplain facies) and subarkosic (braidplain facies) compositions which are considered suitable frameworks for potential reservoir rocks. Primary porosity is mainly reduced during early diagenesis through moderate mechanical compaction and formation of K-feldspar overgrowth, gypsum, dolomite and phyllosilicate cements. Early mesodiagenesis is testified by low chemical compaction and quartz cementation. Telodiagenetic calcite filling fractures and K-feldspar dissolution determined the final configuration of analysed sandstones. Mercury injection-capillary pressure technique reveals overbank deposits in the floodplain as the least suitable potential reservoirs because of their lowest open porosity (OP < 16%), permeability (k < 5 mD) and small dimensions. On the other hand, braidplain deposits show the highest values of such properties (OP up to 31.6% and k > 95 mD) and greater thickness and lateral continuity, so being considered the best potential reservoir. The accurate estimation of TIBEM microscale attributes can provide important input for appraisal and enhanced oil recovery performance in TAGI and in others reservoirs consisting on similar fluvial sandy facies.     

Experimental evaluation of reservoir quality in Mesozoic formations of the Perth Basin (Western Australia) by using a laboratory low field Nuclear Magnetic Resonance

Accurate porosity and permeability evaluation of rock formations is critical to estimate the quality and resource potential of a reservoir. In addition to directly measure the porosity and pore size distribution, low field Nuclear Magnetic Resonance (NMR) is able to measure the effective porosity and estimate the in-situ formation permeability, though its robustness is arguable and requires calibrations on cores with specific lithologies.The Mesozoic formations of the central Perth Basin (Western Australia) host hot sedimentary aquifers and recently became key targets for geothermal heat extraction. A collection of cores was retrieved from three wells intersecting these units. The characterisation of their flow properties complements the current evaluation of the Perth Basin by adding new data on effective porosity, pore size distribution, pore geometry and calibration of predictive models for the permeability according to a comprehensive facies classification scheme.This study highlights the consistency of the NMR approach when compared to conventional helium injection method. Most favourable lithologies for well production correspond to very coarse to fine sandstones of fluvial channel fill with porosities >15% and permeabilities >>1 mD. Similarly, these facies exhibit (i) the highest effective porosities, (ii) the highest pore space to pore throat ratio, and (iii) the lowest contribution of clay bound water. These aspects confirm the importance of clay occurrence in the assessment of the flow efficiency of a formation.The Yarragadee Formation presents the best reservoir quality regarding its porosity and permeability, even though high discrepancies occur locally owing to the great variability of lithofacies encountered. The scattered values observed for the Lesueur Sandstone are likely to be due to the basin architecture and fault system which generate different mechanical compaction and secondary cementation. Given an adequate facies analysis, the NMR method represents a powerful tool to estimate the flow efficiency of a reservoir.     

扬州市江都区地热资源前景分析

江都区位于宁通隆起与苏北坳陷接合部,具有良好的地热地质开发利用前景。地热资源主要为传导型,分为孔隙型和岩溶裂隙型2个地热系统。根据地热地质条件分为北部、中部及南部3个地热资源分区。北部以孔隙型为主,中部、南部以构造裂隙型为主。预测可采地热水资源总量约11.18万m3/d,地热水温度40～68℃。     

Pore orientation of granular materials during biaxial compression

The local pore spaces in granular materials tend to be aligned parallel to the major principal stress direction upon particle mobilization. Manifestation of this response has been numerically validated in our previous studies with the aid of discrete element method modeling and image processing techniques during creep and shearing. We now extend the modeling of pore geometry, constructed with spherical particles, to assemblies of particle clumps. Two-dimensional simulations are performed for both loose and dense assemblies of spherical particles and particle clumps. Each particle packing is bound by rigid or flexible walls and subjected to biaxial compression and the particle mobilization effect on the evolution of pore orientation is explored. Randomly shaped pores surrounded by adjacent particles are geometrically quantified by Delaunay tessellation and fitted with ellipses. Results show that localization is apparent in dense assemblies, in particular for clumped particle packing, while loose assemblies exhibit diffusive failure. Small pores within well-defined shear bands tend to align either parallel to the direction of the shear band or perpendicular to the major principal stress. On the other hand, small pores within the blocks and large pores have a tendency to become elongate towards the major principal stress direction. This study reveals for the first time that pore orientation is dependent upon particle shape, pore size, and assembly conditions on the pore and global scales.     

Design of drainage blankets for leachate recirculation in bioreactor landfills using two-phase flow modeling

Drainage blankets (DB) are used for leachate recirculation in bioreactor landfills and consist of highly permeable material placed over a large area of the landfill with the leachate injection pipe embedded in the material at specified locations. DBs are generally installed at different depth levels during the waste filling operations. Very limited information is reported on performance of DBs, and that which exists is based on a small number of field monitoring and modeling studies. A rational method for the design of landfills using DBs has not been developed. This study performs a parametric analysis based on a validated two-phase flow model and presents design charts to guide the design of DBs for given hydraulic properties of MSW, the leachate injection rate and the dimensions and locations of the DB as measured from the leachate collection and recirculation system (LCRS) located at the bottom of the landfill cell. Numerical simulations were performed for the two established MSW conditions: homogeneous–isotropic and heterogeneous–anisotropic waste. The optimal levels of leachate saturation, wetted width, wetted area and developed pore water and pore gas pressures were determined, and design charts using the normalized parameters were developed. An example is presented on the use of design charts for typical field application.