Uniaxial compression and tension tests of anthracite and loading rate dependence of peak strength

The mechanical characteristics of coal under uniaxial compressive stress and uniaxial tensile stress are key factors in investigations of the stability of galleries and coal faces, and are vital considerations for the efficient design of coalmines, disaster prevention, and environmental preservation. These mechanical characteristics have long been a topic of research, but remain insufficiently understood. In this study we performed uniaxial compression tests and uniaxial tension tests on coal, with particular attention to two concerns. The first was to measure the loading rate dependence of the peak strength of coal. Coal shows high sample-to-sample scatter in strength; test methods that are successful in comparatively homogeneous rock types cannot be used for coal. We therefore used an alternative test method that was recently developed by the authors. Anthracite samples were subjected to alternating slow and fast strain rates. Measured variations in stress during this process were used to estimate the loading rate dependence of peak strength. The second objective was to obtain complete stress–strain curves for coal under uniaxial tensile stress. It is difficult to hold samples secure during a tensile test; consequently, such curves have yet to be obtained. This study presents a successful application of the authors' method to the analysis of coal samples, yielding a complete stress–strain curve under tensile stress. The two methods presented here hold promise for application not only to anthracite but also to a wide variety of coals. It is possible to derive the values of the constants used in constitutive equations from the obtained experimental results. Once these equations are determined, they can be incorporated into finite-element software to investigate various time-dependent behaviors of coal and aid in the efficient design of coalmines and the prevention of subsidence and mine disasters.     

Effects of dynamic shear strength and time-histories stress analysis on newmark sliding block analyses

A simplified procedure for evaluating aseismic stability of slope subjected to earthquake shaking, in which the effect of dynamic shear strength and time-history stress on the yielding angular acceleration of sliding block is taken into account, is presented. The fundamental feature of this procedure is the dynamic shear strength. The numerical computations are performed by using the proposed method. It is shown that the computed sliding displacement for a given core dam, with either method of dynamic shear strength properly considered, is more rational compared with the conventional computational results based on static shear strength.     

冲击凿岩钎杆的瞬态动力学分析

以ANSYS为平台，按照真实工作状态对凿岩钎杆进行了瞬态动力学分析，并对不同活塞形状下分析结果数据进行了比较，为冲击凿岩系统设计提供了理论依据。     

PDC钻头切削齿破岩载荷规律的分析

对PDC钻头冠部形状及不同的布齿密度和切削齿在不同的磨损状态下对PDC钻头切削齿受力的影响进行了分析；用相邻的3个切削齿之间的关系(不同的切削齿与切削齿之间的径向距离和切削齿之间的高度差)来分析PDC钻头冠部形状和切削齿布齿密度对切削齿受力的影响，以及将切削齿的磨损状态简化成与切削齿在钻头上装配方向垂直的平面来分析切削齿磨损状态对切削齿受力的影响。     

双坡面临空岩质边坡滑动破坏模式下的稳定性分析

多数岩质边坡稳定性分析已基本解决了常走向单坡面临空的边坡平面滑动问题。然而,在路堑边坡工程和自然边坡中有很多边坡坡面并不是平面,它包含多个坡面。多坡面边坡包含两个或多个不同走向的坡面。多坡面边坡几何特征不同于单坡面边坡,所以滑动条件也不一样。在赤平投影图上,多坡面的滑动包络线是组成边坡的每个坡面单独投影包络线的组合。为了探讨方便,只讨论了双坡面临空岩质边坡的滑动破坏模式,并将其分为双坡面临空下的平面破坏和楔形体破坏。在赤平投影图上,双坡面滑动区域定义为双坡面边坡滑动包络图中两侧坡面的真倾线之间的面积。如果有一两个节理面真倾向线落在滑动区内,滑动破坏才可能发生。     

Attenuation of aqueous metal transport at two natural acid rock drainage occurrences in the Yukon Territory, Canada

Naturally acidic drainage associated with pyritic black shale has been observed in many locations in the Yukon Territory. While not necessarily linked to known mineral deposits, most of these natural acid rock drainage occurrences show elevated dissolved concentrations of trace elements, especially zinc, nickel, copper, cadmium and arsenic. Based on field observations, microbial investigation, chemical analyses and geochemical modeling, the fate and transport of potentially deleterious elements at two natural acid drainage occurrences with slightly different settings are examined. The Macintosh Creek is a small, acidic stream （pH 2.98-3.40）, 2 km long, located in the Macmillan Pass area of east-central Yukon amidst known sedimentary exhalative massive sulfide mineralization but remains undisturbed by exploration activities. Its trace metal content is apparently derived from groundwater discharges, which gave as much as 5.0, 2.5, 0.7, 0.13 and 0.03 mg/L ofZn, Ni, Cu and As, respectively. Interaction and sorption reactions with algal mats, biofilms and iron oxyhydroxides appear to be the dominant mechanisms attenuating aqueous contaminant transport along the stream. Cryogenic precipitation further consolidates the ferricrete formation and reduces the mobility of the sorbed metals. The tributaries of the Engineering Creek along the Dempster Highway in northern Yukon drain through a series of dolomite, phyllite, argillite, limestone, black shale, sandstone and conglomerate with no known concentration of mineralization. In this area, the water chemistry fully reflects the local geology with acidic streams invariably associated with black shale occurrences. Groundwater seeps in the headwaters area of the km-180 Creek completely enclosed in black shale gave pH 3.0 and as much as 148, 39, 2.9 and 9.1 mg/L of Zn, Ni, Cu and As, respectively. Sorption with iron oxyhydroxide and organic matter appear to dominate the attenuation of contaminant transport along the stream. However, once entered into carbonate-dominated terrains, secondary carbonate minerals exercise additional geochemical control on the local water chemistry as a result of neutralization.     

Naturally acidic and metalliferous waters at unmined volcanogenic massive sulfide deposits in the Bonnifield mining district, Alaska Range, east-central Alaska

The Bonnifield district hosts 26 tmmined volcanogenic massive sulfide （VMS） occurrences. Environmental geochemical samples of water and stream sediment were collected at several occurrences, concentrating on the two best-exposed and largest deposits, Red Mountain （RM） and Sheep Creek （SC）. Limited samples were also collected at the poorly exposed WTF deposit. The deposits are Late Devonian to Early Mississippian, and are hosted by felsic metavolcanic and carbonaceous schist members of the Totatlanika Schist or Keevy Peak Fm. Spring and stream waters at RM and SC have pH values commonly 〈3.5 （as low as 2.4 at RM and 2.5 at SC）, high conductivity （up to 11000 μS/cm）, and very high （Is to 100s mg/L） dissolved contents of Al, Cd, Co, Cu, Fe, Ni, and Pb. Waters at RM are characterized by extremely high REE contents （summed REE median 3200 μg/L, n=33）. At both RM and SC, pyrite oxidation and dissolution produce low pH waters that interact with and dissolve bedrock minerals, resulting in acidic, metal-laden, naturally degraded streams that are mostly devoid of aquatic life. Ferricrete is common. In contrast, WTF barely produces a surficial environmental footprint, mostly due to topography and relief. RM and SC are well exposed in the areas of relatively high relief, and both exhibit extensive areas of quartz-sericite-pyrite-alteration. While WTF shares many of the same deposit-and alteration characteristics, it is concealed by tundra in a large, nearly flat area. Surface water at WTF is absent and outcrops are sparse. Even though WTF is roughly the same size as Red Mountain （both around 3 million tonnes） and has similar base- and precious-metal grades, the surficial geochemical manifestation of WTF is minimal. However, exposure through mining of the altered, mineralized rock at WTF potentially could initiate the same processes of pyrite oxidation, acid generation, and mineral dissolution that are observed naturally at RM and SC.     

Rock fracturing by explosive energy: review of state-of-the-art

A study of the dynamic rock fracture initiation and propagation due to explosive energy is presented through a detailed state-of-the-art review. Explosive energy dissipation in crushing and fracturing is examined and the various means to enhance the explosive energy utilization for dynamic rock fracturing are reviewed. The study highlights the need for a better understanding of the dynamic fracturing process particularly in the presence of in situ stresses in the rock mass.     

Investigation of the effect of aggregate shape and surface roughness on the slake durability index using the fractal dimension approach

Argillaceous rocks cover about one thirds of the earth's surface. The major engineering problems encountered with weak- to medium-strength argillaceous rocks could be slaking, erosion, slope stability, settlement, and reduction in strength. One of the key properties for classifying and determining the behavior of such rocks is the slake durability. The concept of slake durability index (SDI) has been the subject of numerous researches in which a number of factors affecting the numerical value of SDI were investigated. In this regard, this paper approaches the matter by evaluating the effects of overall shape and surface roughness of the testing material on the outcome of slake durability indices.

For the purpose, different types of rocks (marl, clayey limestone, tuff, sandstone, weathered granite) were broken into chunks and were intentionally shaped as angular, subangular, and rounded and tested for slake durability. Before testing the aggregate pieces of each rock type, their surface roughness was determined by using the fractal dimension. Despite the variation of final values of SDI test results (values of I_d), the rounded aggregate groups plot relatively in a narrow range, but a greater scatter was obtained for the angular and subangular aggregate groups. The best results can be obtained when using the well rounded samples having the lowest fractal values. An attempt was made to analytically link the surface roughness with the I_d parameter and an empirical relationship was proposed. A chart for various fractal values of surface roughness to use as a guide for slake durability tests is also proposed. The method proposed herein becomes efficient when well rounded aggregates are not available. In such condition, the approximate fractal value for the surface roughness profile of the testing aggregates could be obtained from the proposed chart and be plugged into the empirical relation to obtain the corrected I_d value. The results presented herein represent the particular rock types used in this study and care should be taken when applying these methods to different type of rocks.     

Strain softening of K0-consolidated Changi sand under plane-strain conditions

Experimental results are presented in this paper to study the strain softening behaviour of a marine dredged sand under plane-strain conditions. K₀ consolidated drained and undrained tests were conducted using a new plane-strain apparatus to characterize the strain softening behaviour of the sand under plane-strain conditions. For medium dense specimens, strain softening and shear bands were observed to occur under both drained and undrained conditions. For very loose specimens, no shear bands were observed and critical states were reached within the homogeneous deformation region in both drained and undrained tests. Strain softening was observed to occur at small strain for very loose specimens under undrained conditions. Two types of strain softening, the homogenous softening and banding softening, were identified and the conditions for strain softening were established. The results obtained from this study were compared with the studies by Han and Vardoulakis (Géotechnique 41(1):49–78, 1991), Finno et al. (J Geotech Eng ASCE 122(6):462–473, 1996, Géotechnique 47(1):149–165, 1997) and Mokni and Desrues (Mech Cohes-Frict Mat 4:419–441, 1998).