燕山水库坝基防渗墙优化设计

因现场资料不足或分析手段落后等原因,当前进行水库坝基防渗墙设计,往往存在过于保守的倾向。以河南省燕山水库为例,基于优化设计的思路,采用目前较为成熟的二维有限单元法,对不同防渗条件下的坝基渗流场分别进行了模拟,并将计算所得比降、流量与允许比降、允许流量做了对比,从定量的角度提出了既安全、又经济的防渗方案:防渗墙厚度取0.8m,深度取打入破碎带5m。     

房产测绘平面图系统的实现研究

随着城市规划管理的不断发展．使得城市房产测绘单位采用大型空间数据库管理测绘平面图资料成为必然。通过建立房产测绘平面图系统，可以有效地解决数据标准不一致．图数不能互访，测绘各部门无法协调一致等问题，充分发挥网络功能，提升整个城市的房产管理水平．达到房产管理和房产服务一体化的目标。本文详细论述了房产测绘平面图系统的概念、设计原则和系统功能．在南京数字房产共享平台的建设中得到了实现．并取得了良好的效果。     

Hyper Redundancy for Accuracy Enhancement in Automated Close Range Photogrammetry

A generic network design in close range photogrammetry is one where optimal multi-ray intersection geometry is obtained with as few camera stations as practicable. Hyper redundancy is a concept whereby, once the generic network is in place, many additional images are recorded, with the beneficial impact upon object point precision being equivalent to the presence of multiple exposures at each camera position within the generic network. The effective number of images per station within a hyper redundant network might well be in the range of 10 to 20 or more. As is apparent when it is considered that a hyper redundant network may comprise hundreds of images, the concept is only applicable in practice to fully automatic vision metrology systems, where it proves to be a very effective means of enhancing measurement accuracy at the cost of minimal additional work in the image recording phase. This paper briefly reviews the network design and accuracy aspects of hyper redundancy and illustrates the technique by way of the photogrammetric measurement of surface deformation of a radio telescope of 26 m diameter. This project required an object point measurement accuracy of σ  = 0·065 mm, or 1/400 000 of the diameter of the reflector.     

三峡库区滑坡治理工程设计中推力荷载计算方法初探

随着三峡水利工程的逐步实施，淹没区移民及新城镇建设等人类工程活动的加剧，以滑坡为主的环境地质问题日益突出。本文从稳定系数、安全系数入手，对铁道、公路等部门常用的设计计算原理进行了研究，并由此类比分析研究了三峡区回水后或库水位正常运行条件下，滑坡治理工程设计计算方法。     

Optimal design of passive energy dissipation systems based on H∞ and H2 performances

Passive energy dissipation devices (EDDs), such as viscous dampers, viscoelastic dampers, etc., have been used to effectively reduce the dynamic response of civil infrastructures, such as buildings and bridges, subject to earthquakes and strong winds. The design of these passive energy dissipation devices (EDDs) involves the determination of the optimal locations and the corresponding capacities. In this paper, we present two optimal design methodologies for passive EDDs based on active control theories, including H_∞ and H₂ performances, respectively. The optimal design methodologies presented are capable of determining the optimal locations and the corresponding capacities of EDDs. Emphasis is placed on the application of linear matrix inequality (LMI) for the effective design of passive EDDs using the popular MATLAB toolboxes. One important advantage of the proposed approaches is that the computation of the structural response is not needed in the design process. The proposed optimal design methodologies have been applied to: (i) a 10‐storey building and a 24‐storey building both subject to earthquake excitations, and (ii) a 76‐storey wind‐excited benchmark building, to demonstrate the advantages of the proposed design methodologies over the conventional equal capacity design. Copyright © 2002 John Wiley & Sons, Ltd.     

Towards a direct collapse–load method of design for concrete frames subjected to severe ground motions

Most current methods of design for concrete structures under earthquake loads rely on highly idealized ‘equivalent’ static representations of the seismic loads and linear‐elastic methods of structural analysis. With the continuing development of non‐linear methods of dynamic analysis for the overload behaviour and collapse of complete concrete structures, a more direct and more accurate design procedure becomes possible which considers conditions at system collapse. This paper describes an evaluation procedure that uses non‐linear dynamic collapse–load analysis together with global safety coefficients. A back‐calibration procedure for evaluating the global safety coefficients is also described. The aim of this paper is to open up discussion of alternative methods of design with improved accuracy which are necessary to move towards a direct collapse–load method of design. Copyright © 2002 John Wiley & Sons, Ltd.     

桥梁隔震体系振动台试验研究(IV)——隔震桥梁的设计方法探讨

在前文模型试验的基础上 ,本文总结归纳了隔震桥梁的设计方法与设计流程 ,着重论述探讨了隔震桥梁的概念设计与细部构造设计应注意的问题     

地震静校正全局最优化问题的求解

针对地震静校正存在的非线性和多参数性等问题，本文提出了一种全局优化的剩余静校正方法.在模型更新规则上，把模拟退火方法和均匀优化设计方法结合在一起，使模型的更新更为合理，从而加快了搜寻全局最优解的速度.同时提出了模型的不同分量的温度参数和退火过程的选取方式，把温度参数的选取与地震剖面的能量联系起来，使温度参数的选取具有自适应的特点.该方法克服了常规模拟退火方法所具有的寻优空间不均匀以及退火参数需通过多次试验选取的缺陷.通过实际地震资料的计算证明，本文提出的方法对地震静校正问题合理而有效.     

Recent developments in seismically isolated buildings in Japan

The Building Standard Law of Japan and related Enforcement Order and Notifications have been substantially revised since the year 2000 to introduce a performance-based regulatory and deregulation system for building control systems. Up to then, time-history analyses were mandatory for isolated buildings and had to be specially approved by the Minster of the Ministry of Construction (MOC). Simplified design procedures based on the equivalent linear method for seismically isolated buildings have been issued as “Notification 2009 — Structural calculation procedure for buildings with seismic isolation” from MOC, and are now integrated into the Ministry of Land, Infrastructure, and Transportation (MLIT). Along with Notification 2009, “Notification 1446 of year 2000 — Standard for specifications and test methods for seismic isolation devices” was also issued. Buildings with heights equal to or less than 60m and that are designed according to these Notifications, including base isolated buildings, only need approval from local building officials, and no longer require the special approval of the Minister of MLIT. This paper summarizes: 1) some statistics related to buildings with seismic isolation completed up to the end of 2001; 2) simplified design procedures required by Notification 2009 of year 2000; and 3) performance of seismic isolation devices required by Notification 1446 of year 2000.     

辽宁省抚顺市区地质灾害监测系统设计方案

抚顺市地质灾害监测系统，由5方面工作内容组成：(1)建立统一可靠的城市高程起算基准；(2)扩展现有的沉降监测网，使分散的监测点联合形成全面、统一的监测网；(3)对浑河断裂带主断层实施监测；(4)对西露天采坑北坡滑坡重点区和采煤沉陷重点区实施水平位移监测；(5)利用计算机技术和地理信息系统(GIS)技术，建立抚顺市地质灾害信患系统。该系统是城市地质灾害防治的基础工程。系统应用了先进的监测手段及数据处理技术。文章介绍了系统的设计方案。