颗粒破碎对绢云母片岩强度和变形影响的试验研究

为进一步弄清颗粒破碎对软岩粗粒料强度、变形的影响,开展2组不同初始干密度下的绢云母片岩粗粒料的固结排水三轴试验,分析了绢云母片岩粗粒料颗粒破碎规律,并探讨了颗粒破碎对绢云母片岩粗粒料力学性质的影响。结果表明,绢云母片岩粗粒料相对破碎率随围压的增加而增大,但颗粒破碎增幅速率受初始干密度影响较大,颗粒破碎与围压之间的关系可用线性关系描述;由于初始孔隙率的影响,使得试样在同一应力水平下高密度试样颗粒破碎明显高于低密度试样;颗粒破碎对高密度试样抗剪强度降低的影响高于低密度试样,导致两种干密度试样的应力-应变曲线在某处出现相交,最终出现初始密度低的试样抗剪强度大于初始密度高的试样抗剪强度的现象;高密度试样孔隙率较小,其剪胀因子一直保持在1附近,而低密度试样孔隙率较大,受颗粒破碎和剪胀的影响迟缓一些,低密度试样体变较高密度要大些,但整体上由于颗粒破碎和剪胀的影响,绢云母片岩粗粒料的体变均不大。     

Talc-phengite-albite assemblage in piemontite-quartz schist of the Sanbagawa metamorphic belt, central Shikoku, Japan

Abstract The talc (Tlc) + phengite (Phn) + albite (Ab) assemblage is newly confirmed in MnO^total-rich (1.65 wt% in average) piemontite-quartz schists from the intermediate- and high-grade part of the Sanbagawa belt, central Shikoku, Japan. Talc is in direct contact with Phn, Ab and chlorite (Chl) with sharp boundaries, suggesting that these four phases mutually coexist. Other primary constituents of the Tlc-bearing piemontite-quartz schist are spessartine, braunite, hematite (Ht), crossite/barroisite and dolomite. Phlogopite (Phl) rarely occurs as a later stage mineral developing along the rim of Phn. The studied piemontite-quartz schist has mg# (= Mg/(Mg + Fe²⁺)) ~ 1.0, because of its high oxidation state. Schreinemakers' analysis in the KNMASH system and the mineral assemblage in the Sanbagawa belt propose a possible petrogenetic grid, in which the Tlc–Phn assemblage is stable in a P-T field surrounded by the following reactions: lower-pressure limit by Chl + Phl + quartz (Qtz) = Phn + Tlc + H₂O as proposed by previous workers; higher-pressure limit by glaucophane + Qtz = Tlc + Ab + H₂O; and higher-temperature limit by Tlc + Phn + Ab = Phl + paragonite + Qtz + H₂O. Thermodynamic calculation based on the database of Holland & Powell (1998) , however, suggests that the Tlc–Phn stability field defined by these reactions is unrealistically limited around 580–600 °C at 11.6–12.0 (± 0.7) kbar. Schreinemakers' analysis in the KNMA-Fe³⁺-SH system and the observed mineral assemblage predict that Chl + crossite = Tlc + Ab + Ht + H₂O is a preferable Tlc-forming reaction in the intermediate-grade part of the Sanbagawa belt and that excess Ab + hematite narrows the stability field of the Tlc–Phn assemblage.     

四川冕宁木落寨稀土矿床稀土矿化与围岩特征

木落寨矿床是冕宁—德昌稀土元素(REE)矿带内的主要稀土矿床,位于矿带北段,雅砻江断裂以西。该稀土矿床的形成与正长岩-碳酸岩杂岩体密切相关。与冕宁—德昌REE矿带中其它矿床例如牦牛坪、大陆槽矿床不同的是,牦牛坪和大陆槽矿床的围岩主要是石英闪长岩,而木落寨REE矿床中围岩较复杂,主要有大理岩、绿片岩、碱性花岗岩等。已有研究表明石英闪长岩并不是牦牛坪和大陆槽矿床稀土元素的主要来源,对木落寨矿床来说,围岩对成矿的作用还需进一步研究。采用ICP-MS与XRF,对大理岩和绿片岩这两种主要的围岩进行主微量元素分析,全岩稀土配分曲线显示轻稀土亏损(大理岩3×10~(–6)~20×10~(–6),绿片岩62×10~(–6)~74×10~(–6)),重稀土平坦,总稀土含量低(大理岩4×10~(–6)~21×10~(–6),绿片岩86×10~(–6)~97×10~(–6)),与本次研究的木落寨正长岩中稀土含量(592×10~(–6)~2 026×10~(–6))和以往研究的冕宁—德昌成矿带其他三个矿床的碳酸岩-正长岩杂岩体中稀土含量(碳酸岩2 470×10~(–6)~40 807×10~(–6),正长岩630×10~(–6)~3 233×10~(–6))相比,大理岩和绿片岩中稀土元素含量过低,显示在稀土物质来源上,这两种围岩可能对成矿贡献不大,根据剖面展示,矿体大部分出现在正长岩裂隙中,极少部分出现在正长岩和大理岩接触面中,大理岩可能提供碳酸根离子,促进交代和成矿作用的进行。木落寨矿石类型主要是细脉浸染型,少量为条带型。通过手标本、镜下和BSE图像观察,脉石矿物主要有萤石+方解石+重晶石+石膏+黄铁矿+方铅矿+石英+金云母等,矿石矿物为氟碳铈矿,氟碳铈矿叠加在已形成的脉石矿物之上,显示矿床主要形成于热液阶段最晚期。     

各向异性片岩的微观组构信息定量提取与断面形貌特征分析

取3类具有明显片理面的武当群片岩,采用偏光显微镜、扫描电镜研究其微观组构、断面形貌特征。构建了面积百分比、尺寸与周长-面积分形维数、定向分布系数等指标,利用IPP专业图像处理软件,对矿物和孔隙(微裂隙)两系统的含量、形态、分布特征等进行定量分析;并基于Matlab的数字图像处理技术,对断裂面粗糙度展开定量评价。偏光显微镜下显示,片岩具有矿物定向排列与粒、片状矿物近互层状分布的典型特征。矿物系统的微观定量分析结果表明:武当群片岩白云母的含量为11%~30%;小岛法计算的白云母矿物周长-面积分形维数为1.31~1.39;定向分布系数为0.61~0.85;微裂隙依附于白云母矿物边缘孕育、扩展,导致武当群片岩的孔隙(微裂隙)微观指标与对应的矿物微观指标有较强的相关性。沿片理面的片岩断面主要呈现沿晶破坏特征,断口较平坦,基于断面形貌图绘制的灰度信号波曲线的盒维数为1.48~1.60;斜交片理面破裂的片岩断面以穿晶破坏为主,有穿晶-沿晶破坏交替而生的迹象,断口粗糙起伏,对应的灰度信号波曲线的盒维数为1.65~1.69。武当群片岩的断面粗糙度各向异性约为1.03~1.14。     

石鼓-黎明地区变沉积岩系的深熔时代和物源

以出露于石鼓-黎明地区的黑云母石英片岩及其深熔脉体为重点研究对象,对其中的锆石进行了阴极发光图像分析、SHRIMP和LA-ICP-MS U-Pb年代学研究。阴极发光图像显示,黑云母石英片岩中大部分锆石保留清晰的振荡环带;深熔脉体中大部分锆石具有核-边结构,核部保留清晰的振荡环带或呈灰色无分带结构,边部较窄呈黑色。对黑云母石英片岩及其深熔脉体中锆石核部进行定年,得到年龄范围为2 637～743 Ma,具有858～852 Ma的主要年龄峰值,表明其主要物质来源为扬子板块西缘新元古代岩浆岩,同时也有太古代-古元古代基底岩石的加入,沉积时代应晚于852 Ma。深熔脉体锆石边部的Th/U值较小(0. 1),得到206Pb/238U年龄变化于225～197 Ma之间,可能代表了变沉积岩的变质-深熔时代,该年龄与金沙江-点苍山-哀牢山变质带二叠纪-三叠纪变质事件的时代相一致。     

木兰山蓝片岩中斜黝帘石—低铁绿帘石连生体的确定

电子探针和光学显微镜联合分析表明，木兰山蓝片岩中存在斜黝帘石－低铁绿帘石连生体。界面区Fe、Al元素的线扫描曲线研究表明，（Fe,Al)类质同象替代为连生体界面共晶膜的形成机制。木兰山蓝片岩中斜黝帘石－低铁绿帘石连生体的确定，说明电子探针和光学显微镜联合分析可有效确定光学性质和化学成分均相近的微细粒连生体的组成矿物，其结果对认识木兰山蓝片岩的变质演化具有指示意义。     

拉萨地块松多超高压变质带含石榴石云母石英片岩的变质演化相平衡模拟

拉萨地块松多超高压变质带含石榴石白云母石英片岩为榴辉岩的围岩,岩石的矿物组合为石榴石、白云母、钠长石、绿泥石、石英及少量金红石、榍石。石榴石具有明显的成分环带,从核部到幔部Xprp=[Mg/(Mg+Fe+Mn+Ca)]缓慢升高,Xsps=[Mn/(Mg+Fe+Mn+Ca)]逐渐降低,表明石榴石从核部到幔部的成分记录了温度逐渐升高的进变质过程;幔部到边部,Xprp=[Mg/(Mg+Fe+Mn+Ca)]略微降低,Xgrs=[Ca/(Mg+Fe+Mn+Ca)]明显升高,Xsps=[Mn/(Mg+Fe+Mn+Ca)]先升高后降低,表明石榴石边部成分受到了退变质作用改造,呈现扩散环带的特征。利用Thermocalc变质相平衡计算软件在Mn NCKFMASHO体系下计算出含石榴石云母石英片岩的P-T、P-M(H2O)视剖面图,结合石榴石镁铝榴石等值线、钙铝榴石等值线及饱和水含量等值线限定出含石榴石云母石英片岩的峰期变质条件为约27×105k Pa,523/580℃,对应的峰期矿物组合为(g-Jd-Cr-Law(+Phn+q/Coe+H2O)。石榴石核部到幔部成分记录了主要的进变质演化,结合饱和水等值线的变化,判断进变质阶段为升温升压的冷俯冲过程,岩石经历了蓝片岩相至榴辉岩相的变质演化;P-M(H2O)视剖面图及饱和水等值线反映了岩石在减压中的流体行为,通过其变化特征可以确定岩石在峰期之后先经历近等温降压的早期退变质过程,晚期降温降压的退变轨迹则由石榴石边部成分所确定,此过程中,岩石发生了角闪岩相至绿帘角闪岩相变质,并在后期经历了绿片岩相变质叠加。近等温降压的退变质过程反映了快速抬升的构造运动过程,早期硬玉转变为钠长石可能发生在这个阶段。对比含石榴石云母石英片岩与榴辉岩的P-T轨迹,峰期变质温压及变质演化特征,提出含石榴石云母石英片岩曾经历过高压变质,结合野外相互伴生的地质关系,认为该片岩与榴辉岩经历了相同或者相似的俯冲折返过程。     

Ore petrology of the V-Ti magnetite (lodestone) layers of the Kurihundi area of Sargur schist belt,Dharwar craton

The V-Ti magnetite layers (lodestone) occur within the layered gabbro-anorthosites-ultramafic rocks emplaced into the migmatitic gneisses close to the high grade Archeaen Sargur supracrustal rocks in the Kurihundi area. The ore petrographic studies of the lodestone reveal the presence of primary Ti-magnetite, ilmenite, ulvospinel, pleonaste, hematite and pyrite, chalcopyrite, pyrrhotite and secondary Ti-maghemite, martite and goethite as well as secondary covellite. These layers contain Ti-magnetite (60%) and ilmenite (30%) with silicates (<5%) exhibiting granular mosaic texture with well-defined triple junctions and are classified as adcumulus rocks. The grain-boundary relationships in the ores indicate considerable postcumulus growth and readjustment due to combined effects of sintering and adcumulus growth. Intergrowth textures (ulvospinel, ilmenite and pleonaste in Ti-magnetite and hematite in ilmenite) reflects exsolution features crystallized from solid-solutions compositions under different conditions of oxygen fugacities. Larger bodies of pleonaste and ilmenite in Ti-magnetite become lensoid or rounded in outline and these morphological modifications took place during the regional upper amphibolite to lower granulite facies metamorphism at 2.6 Ga ago. The lodestone contains high TiO₂ (20 to 22.59 wt%), with V₂O₅ (0.85 to 1.15%) and Fe₂O₃ ^t (72.03 to 74.25%). Ti-magnetite shows alteration to Ti-maghemite, martite and goethite due to low temperature oxidation and hydration during weathering.     

Quartz microtextures of the Sambagawa schists and their implications in convergent margin processes

Abstract Quartz c-axis fabrics of the Sambagawa schists produced along a late Mesozoic convergent plate margin were analysed so that their tectono-metamorphic history could be clarified. It has been noted by many authors that quartz fabrics produced by earlier phase deformation are easily modified by strain increment during later phase deformation. This paper attempts to elucidate the high-temperature phases of prograde metamorphism (Sim-Bim phase) and of retrograde metamorphism (Sb₁ phase and Sb₂₋₁ phase) from quartz grains included in garnet and plagioclase porphyroblasts. Quartz c-axis fabrics for all these phases are explained in terms of a type I crossed girdle, without (only rarely with) higher concentration in the principal axis of strain Y (X>Y>Z), that must have been produced by the activity of a dominant slip system such as rhomb and basal. As a result, the plastic deformation of quartz, which was responsible for the formation of the type I crossed girdle, occurred even under temperatures greater than 500°C and pressures a little greater than 10–11 kb, which correspond to the physical condition of the Sim-Bim phase. It has been assumed that a high strain rate (and/or low H₂O content) caused rhomb and basal to be active as dominant slip systems in the subduction zone related to the formation of the Sambagawa schists even under high temperatures (> 500°C).     

The effect of whole-rock MnO content on the stability of garnet in pelitic schists during metamorphism

Garnet-bearing mineral assemblages are commonly observed in pelitic schists regionally metamorphosed to upper greenschist and amphibolite facies conditions. Modelling of thermodynamic data for minerals in the system Na₂O–K₂O–FeO–MgO–Al₂O₃–SiO₂–H₂O, however, predicts that garnet should be observed only in rocks of a narrow range of very high Fe/Mg bulk compositions. Traditionally, the nearly ubiquitous presence of garnet in medium- to high-grade pelitic schists is attributed qualitatively to the stabilizing effect of MnO, based on the observed strong partitioning of MnO into garnet relative to other minerals. In order to quantify the dependence of garnet stability on whole-rock MnO content, we have calculated mineral stabilities for pelitic rocks in the system MnO–Na₂O–K₂O–FeO–MgO–Al₂O₃–SiO₂–H₂O for a moderate range of MnO contents from a set of non-linear equations that specify mass balance and chemical equilibrium among minerals and fluid. The model pelitic system includes quartz, muscovite. albite, pyrophyllite, chlorite, chloritoid, biotite, garnet, staurolite, cordierite, andalusite, kyanite. sillimanite, K-feldspar and H₂O fluid. In the MnO-free system, garnet is restricted to high Fe/Mg bulk compositions, and commonly observed mineral assemblages such as garnet–chlorite and garnet–kyanite are not predicted at any pressure and temperature. In bulk compositions with X_Mn= Mn/(Fe + Mg + Mn) > 0.01, however, the predicted garnet-bearing mineral assemblages are the same as the sequence of prograde mineral assemblages typically observed in regional metamorphic terranes. Temperatures predicted for the first appearance of garnet in model pelitic schist are also strongly dependent on whole-rock MnO content. The small MnO contents of normal pelitic schists (X_Mn= 0.01–0.04) are both sufficient and necessary to account for the observed stability of garnet.