Numerical simulation for 1975 Haicheng and 1999 Xiuyan earthquake processes by DDA+FEM

Introduction The Xiuyan earthquake(MS=5.4)on Nov.29,1999,occurred between Hushan town and Pi-anling town at the southeast end of the aftershocks of Haicheng earthquake(MS=7.3).These two earthquakes′sequences are highly similar in the way that the foreshocks are very frequent,focal mechanisms of the main shocks are about the same and fault strikes are approximately in the same direction.It is important to study these earthquakes for further research on seismogenesis to fore-cast earthquake…     

Interevent Time Distribution in Seismicity: A Theoretical Approach

This paper presents an analysis of the distribution of the time τ between two consecutive events in a stationary point process. The study is motivated by the discovery of unified scaling laws for τ for the case of seismic events. We demonstrate that these laws cannot exist simultaneously in a seismogenic area. Under very natural assumptions we show that if, after rescaling to ensure Eτ =1, the interevent time has a universal distribution F, then F must be exponential. In other words, Corral’s unified scaling law cannot exist in the whole range of time. In the framework of a general cluster model we discuss the parameterization of an empirical unified law and the physical meaning of the parameters involved. An erratum to this article is available at .     

华蓥山隧道岩溶发育强度垂直分带

论述了华蓥山隧道的岩溶发育特征,根据岩溶发育强度的划分依据和划分标准,结合岩溶发育的历史,采用类比判别法、主因素判别法和综合判别法对岩溶发育强度作了垂直分带,据此预测的溶洞规模与实际情况吻合。     

Relief-rejuvenation and topographic length scales in a fluvial drainage basin, Napf area, Central Switzerland

This paper explores how, and to what extent, a phase of relief-rejuvenation modifies the mode of surface erosion in an approximately 63 km² drainage basin located at the northern border of the Swiss Alps (Luzern area). In the study area, the retreat of the Alpine glaciers at the end of the Last Glacial Maximum (LGM) caused base level to lower by approximately 80 m. The fluvial system adapted to the lowered base level by headward erosion. This is indicated by knickzones in the longitudinal stream profiles and by the continuous upstream narrowing of the width of the valley floor towards these knickzones. In the headwaters above these knickzones, processes are still to a significant extent controlled by the higher base level of the LGM. There, frequent exposure of bedrock in channels and especially on hillslopes implies that sediment flux is to a large extent limited by weathering rates. In the knickzones, however, exposure of bedrock in channels implies that sediment flux is supply-limited, and that erosion rates are controlled by stream power.The morphometric analysis reveals the existence of length scales in the topography that result from distinct geomorphic processes. Along the tributaries where the upstream sizes of the drainage basins exceed 100,000–200,000 m², the mode of sediment transport and erosion changes from predominantly hillslope processes (i.e., landsliding, creep of regolith, rock avalanches and to some extent debris flows) to processes in channels (fluvial processes and debris flows). This length scale reflects the minimum size of the contributing area for channelized processes to take over in the geomorphic development (i.e., threshold size of drainage basin). This threshold size depends on the ratio between production rates of sediment on hillslopes, and export rates of sediment by processes in channels. Consequently, in the headwaters, erosion rates and sediment flux, and hence landscape evolution rates, are to a large extent limited by weathering processes. In contrast, in the lower portion of the drainage basin that adjusts to the lowered base-level, rates of channelized erosion and relief formation are controlled mainly by stream power. Hence, this paper shows that base-level lowering, headward erosion and establishment of knickzones separate drainage basins in two segments with different controls on rates of surface erosion, sediment flux and relief formation.     

Land subsidence and caprock dolines caused by subsurface gypsum dissolution and the effect of subsidence on the fluvial system in the Upper Tigris Basin (between Bismil–Batman, Turkey)

Karstification-based land subsidence was found in the Upper Tigris Basin with dimensions not seen anywhere else in Turkey. The area of land subsidence, where there are secondary and tertiary subsidence developments, reaches 140 km². Subsidence depth ranges between 40 and 70 m. The subsidence was formed as a result of subsurface gypsum dissolution in Lower Miocene formation. Although there are limestones together with gypsum and Eocene limestone below them in the area, a subsidence with such a large area is indicative of karstification in the gypsum. The stratigraphical cross-sections taken from the wells and the water analyses also verify this fact. The Lower Miocene gypsum, which shows confined aquifer features, was completely dissolved by the aggressive waters injected from the top and discharged through by Zellek Fault. This resulted in the development of subsidence and formation of caprock dolines on loosely textured Upper Miocene–Pliocene cover formations. The Tigris River runs through the subsidence area between Batman and Bismil. There are four terrace levels as T1 (40 m), T2 (30 m), T3 (10 m) and T4 (4–5 m) in the Tigris River valley. It was also found that there were some movements of the levels of the terraces in the valley by subsidence. The subsidence developed gradually throughout the Quaternary; however no terrace was formed purely because of subsidence.     

Soil–rock-forming processes and engineering mechanical properties of the ancient gravel stratum near Nanjing, China

The ancient gravel stratum near Nanjing, China, is a major stratum of Cenozoic age along the middle–lower reaches of the Yangtze River. This paper first presents a typical geological profile and material composition of the ancient gravel stratum, and then discusses its geologic origin, soil–rock-forming processes, engineering mechanical properties, and their relations. These analyses are useful for city planning, geotechnical engineering, construction, and characterization of the geological environment in the Nanjing area.     

From the geological to the numerical model in the analysis of gravity-induced slope deformations: An example from the Central Apennines (Italy)

This paper presents the findings from a study on gravity-induced slope deformations along the northern slope of Mt. Nuria (Rieti-Italy). The slope extends from the village of Pendenza to the San Vittorino plain and hosts the Peschiera River springs, i.e. the most important springs of the Central Apennines (average discharge: about 18 m³/s).

Detailed geological-geomorphological and geomechanical surveys, supported by a site stress-strain monitoring system and laboratory tests, led us to define the main evolutionary features of the studied phenomena. Based on the collected data, a “geological-evolutionary model” was developed with a view to identifying a spatio-temporal correlation between relief forms, jointing of the rock mass and its stress conditions. The geological-evolutionary model was expected to improve numerical simulations and to test our assumptions.

The numerical model also allowed us to simulate changes in the stress-strain conditions of the rock mass and correlate them with jointing, seepage, as well as with site-detected and site-monitored forms and deformations. In particular, significant relations between seepage, tensile stresses within the rock mass, karst solution and collapse of cavities were identified.     

Geochemical characteristics of mineral air particles emitted inside a clay atomisation plant which introduces waste recycling processes

The objective of this work is to assess the concentrations of three factions of air particles (settable particles, TSP and PM10) and the levels of several toxic elements in a clay atomisation industry through aerosol sampling at several points inside an industrial plant. Mechanical activities, which produce diffuse emissions, are the main process of discharge of particles in both indoor and outdoor workplace environments in the atomisation plant. The levels of As, Cd, Pb, Zn, Ba and Ni increase in the zones with higher concentrations of particles and lower ventilation. The concentrations of As and F are not influenced by the recycling processes. The levels of Cd and Pb do not show great enrichment in air particles collected inside the atomisation plant although the content of both elements is associated with ceramic muck recycling. Finally, the content of B in waste water is mainly transferred in gaseous phase to the atmosphere during the process of drying by atomisation.     

Detection and 2d modelling of cavities using pole–dipole array

The resistivity method is often used in cave prospecting. In this paper the pole–dipole array ability to detect cavities at different depths and with different water contents is investigated. The research was performed using analogical and numerical modelling. According to the results, empty caves at a depth less than four times its diameter can be easily detected. The ability of the pole–dipole array to detect water-filled caves reaches a minimum at filling percentages of 30–50%. Overburden effects research shows that low resistivity overburden reduces the resolution capability of the array. This study shows that equivalent results can be obtained by modelling the empty caves as infinite resistivity bodies or, alternatively, as very high resistivity ones. The analysis of field data acquired in the Maciço Calcário Estremenho (Portugal) shows the practical importance of the pole–dipole array in cavities prospecting.