Morphodynamics of a bedrock‐alluvial meander bend that incises as it migrates outward: approximate solution of permanent form

In meandering rivers cut into bedrock, erosion across a channel cross‐section can be strongly asymmetric. At a meander apex, deep undercutting of the outer bank can result in the formation of a hanging cliff (which may drive hillslope failure), whereas the inner bank adjoins a slip‐off slope that connects to the hillslope itself. Here we propose a physically‐based model for predicting channel planform migration and incision, point bar and slip‐off slope formation, bedrock abrasion, the spatial distribution of alluvial cover, and adaptation of channel width in a mixed bedrock‐alluvial channel. We simplify the analysis by considering a numerical model of steady, uniform bend flow satisfying cyclic boundary conditions. Thus in our analysis, ‘sediment supply’, i.e. the total volume of alluvium in the system, is conserved. In our numerical simulations, the migration rate of the outer bank is a specified parameter. Our simulations demonstrate the existence of an approximate state of dynamic equilibrium corresponding to a near‐solution of permanent form in which a bend of constant curvature, width, cross‐sectional shape and alluvial cover distribution migrates diagonally downward at constant speed, leaving a bedrock equivalent of a point bar on the inside of the bend. Channel width is set internally by the processes of migration and incision. We find that equilibrium width increases with increasing sediment supply, but is insensitive to outer bank migration rate. The slope of the bedrock point bar varies inversely with both outer bank migration rate and sediment supply. Although the migration rate of the outer bank is externally imposed here, we discuss a model modification that would allow lateral side‐wall abrasion to be treated in a manner similar to the process of bedrock incision. Copyright © 2016 John Wiley & Sons, Ltd.     

Recent increase of river–floodplain suspended sediment exchange in a reach of the lower Amazon River

We analyzed variation of channel–floodplain suspended sediment exchange along a 140 km reach of the lower Amazon River for two decades (1995–2014). Daily sediment fluxes were determined by combining measured and estimated surface sediment concentrations with river–floodplain water exchanges computed with a two‐dimensional hydraulic model. The average annual inflow to the floodplain was 4088 ± 2017 Gg yr^?1 and the outflow was 2251 ± 471 Gg yr^?1, respectively. Prediction of average sediment accretion rate was twice the estimate from a previous study of this same reach and more than an order of magnitude lower than an estimate from an earlier regional scale study. The amount of water routed through the floodplain, which is sensitive to levee topography and increases exponentially with river discharge, was the main factor controlling the variation in total annual sediment inflow. Besides floodplain routing, the total annual sediment export depended on the increase in sediment concentration in lakes during floodplain drainage. The recent increasing amplitude of the Amazon River annual flood over two decades has caused a substantial shift in water and sediment river–floodplain exchanges. In the second decade (2005–2014), as the frequency of extreme floods increased, annual sediment inflow increased by 81% and net storage increased by 317% in relation to the previous decade (1995–2004). Copyright © 2017 John Wiley & Sons, Ltd.     

A one‐dimensional process‐based approach to study reservoir sediment dynamics during management operations

A comprehensive understanding of the dynamics of erosion and sedimentation in reservoirs under different management conditions is required to anticipate sedimentation issues and implement effective sediment management strategies. This paper describes a unique approach combining fluvial geomorphology tools and morphodynamic modeling for analyzing the sediment dynamics of an elongated hydropower reservoir subjected to management operations: the Génissiat Reservoir on the Rhône River. Functional sub‐reaches representative of the reservoir morphodynamics were delineated by adapting natural river segmentation methods to elongated reservoirs. The segmentation revealed the link between the spatial and temporal reservoir changes and the variability of longitudinal flow conditions during reservoir management operations. An innovative modeling strategy, incorporating the reservoir segmentation into two sediment transport codes, was implemented to simulate the dynamics of erosion and sedimentation at the reach scale during historic events. One code used a bedload approach, based on the Exner equation with a transport capacity formula, and the other used a suspended load approach based on the advection–dispersion equation. This strategy provided a fair quantification of the dynamics of erosion and sedimentation at the reach scale during different management operations. This study showed that the reservoir morphodynamics is controlled by bedload transport in upper reaches, graded suspended load transport of sand in middle reaches and suspended load transport of fine sediments in lower reaches. Eventually, it allowed a better understanding of the impact of dam management on sediment dynamics. Copyright © 2017 John Wiley & Sons, Ltd.     

A multidirectional conditional spectrum

This paper presents a procedure to generate multidirectional conditional spectra (MDCS) that allow for the characterisation of seismic demands at different angles of incidence. Being conditional on a particular period and its direction of maximum response, it is considered to be a natural evolution of the conditional spectrum to account for the effects of directionality, that is, the variation of seismic demands as a function of the angle of incidence of ground motions, which can have a significant effect on the performance of different kinds of structures. The three main components needed for the generation of MDCS are explained in detail. Monte Carlo simulations are conducted using different sampling methods to assess the effects of incorporating the correlation between demands at different orientations for the same oscillator period, and a novel correlation model is proposed for this purpose. The statistical characteristics of MDCS, their relation with the conditional spectrum, the advantages of the MDCS over previous definitions of orientation‐specific spectra, and prospective future developments are discussed.     

Permanent earthquake‐induced actions in buried pipelines: Numerical modeling and experimental verification

Buried pipelines are often constructed in seismic and other geohazard areas, where severe ground deformations may induce severe strains in the pipeline. Calculation of those strains is essential for assessing pipeline integrity, and therefore, the development of efficient models accounting for soil‐pipe interaction is required. The present paper is aiming at developing efficient tools for calculating ground‐induced deformation on buried pipelines, often triggered by earthquake action, in the form of fault rupture, liquefaction‐induced lateral spreading, soil subsidence, or landslide. Soil‐pipe interaction is investigated by using advanced numerical tools, which employ solid elements for the soil, shell elements for the pipe, and account for soil‐pipe interaction, supported by large‐scale experiments. Soil‐pipe interaction in axial and transverse directions is evaluated first, using results from special‐purpose experiments and finite element simulations. The comparison between experimental and numerical results offers valuable information on key material parameters, necessary for accurate simulation of soil‐pipe interaction. Furthermore, reference is made to relevant provisions of design recommendations. Using the finite element models, calibrated from these experiments, pipeline performance at seismic‐fault crossings is analyzed, emphasizing on soil‐pipe interaction effects in the axial direction. The second part refers to full‐scale experiments, performed on a unique testing device. These experiments are modeled with the finite element tools to verify their efficiency in simulating soil‐pipe response under landslide or strike‐slip fault movement. The large‐scale experimental results compare very well with the numerical predictions, verifying the capability of the finite element models for accurate prediction of pipeline response under permanent earthquake‐induced ground deformations.     

Evaluation of ASCE 7 equations for designing acceleration‐sensitive nonstructural components using data from instrumented buildings

This study uses instrumented buildings and models of code‐based designed buildings to validate the results of previous studies that highlighted the need to revise the ASCE 7 F_p equation for designing nonstructural components (NSCs) through utilizing oversimplified linear and nonlinear models. The evaluation of floor response spectra of a large number of instrumented buildings illustrates that, unlike the ASCE 7 approach, the in‐structure and the component amplification factors are a function of the ratio of NSC period to the supporting building modal periods, the ground motion intensity, and the NSC location. It is also shown that the recorded ground motions at the base of instrumented buildings in most cases are significantly lower than design earthquake (DE) ground motions. Because ASCE 7 is meant to provide demands at a DE level, for a more reliable evaluation of the F_p equation, 2 representative archetype buildings are designed based on the ASCE 7‐16 seismic provisions and exposed to various ground motion intensity levels (including those consistent with the ones experienced by instrumented buildings and the DE). Simulation results of the archetype buildings, consistent with previous numerical studies, illustrate the tendency of the ASCE 7 in‐structure amplification factor, [1 + 2(z/h)] , to significantly overestimate demands at all floor levels and the ASCE 7 limit of to in many cases underestimate the calculated NSC amplification factors. Furthermore, the product of these 2 amplification factors (that represents the normalized peak NSC acceleration) in some cases exceeds the ASCE 7 equation by a factor up to 1.50.     

Geomorphic effectiveness: a linear concept in a non‐linear world

Geomorphic effectiveness has been an influential concept in geomorphology since its introduction by Reds Wolman and John Miller in 1960. It provided a much needed framework to assess the significance of an event by comparing event magnitude to the resultant geomorphic effects. Initially, this concept was applied primarily in river channels, under the linear assumption that geomorphic responses to similarly sized flood events will be consistent. Numerous authors have since attempted to quantify a direct, proportional relationship between event magnitude and different forms of geomorphic response in a variety of geomorphic settings. In doing so, these investigations applied an array of metrics that were difficult to compare across different spatiotemporal scales, and physiographic and geomorphic environments. Critically, the emergence of other geomorphic concepts such as sensitivity, connectivity, thresholds, and recovery has shown that relationships between causes (events) and geomorphic effects (responses) are often complex and non‐linear. This paper disentangles the complex historical development of the geomorphic effectiveness concept and reviews the utility of various metrics for quantifying effectiveness. We propose that total energy (joules) is the most appropriate metric to use for quantifying the magnitude of disturbance events (cause) and volumetric sediment flux associated with landform modification is the most appropriate metric for quantifying geomorphic effects. While both metrics are difficult to quantify, they are the only ones which facilitate comparison across a range of spatiotemporal scales (comparability) in a variety of geomorphic environments (flexibility). The geomorphic effectiveness concept can continue to be useful provided that geomorphologists use flexible and comparable metrics. Today, geomorphologists are better prepared to consider the influence of non‐linear processes on determinations of geomorphic effectiveness, allowing investigators to not only determine if a disturbance event was effective but also to explain why or why not. Copyright © 2016 John Wiley & Sons, Ltd.     

Real‐time force control for servo‐hydraulic actuator systems using adaptive time series compensator and compliance springs

Servo‐hydraulic actuators have been widely used for experimental studies in engineering. They can be controlled in either displacement or force control mode depending on the purpose of a test. It is necessary to control the actuators in real time when the rate‐dependency effect of a test specimen needs to be accounted for under dynamic loads. Real‐time hybrid simulation (RTHS) and effective force testing (EFT) method, which can consider the rate‐dependency effect, have been known as viable alternatives to the shake table testing method. Due to the lack of knowledge in real‐time force control, however, the structures that can be tested with RTHS and EFT are fairly limited. For instance, satisfying the force boundary condition for axially stiff members is a challenging task in RTHS, while EFT has a difficulty to be implemented for nonlinear structures. In order to resolve these issues, this paper introduces new real‐time force control methods utilizing the adaptive time series (ATS) compensator and compliance springs. Unlike existing methods, the proposed force control methods do not require the structural modeling of a test structure, making it easy to be implemented especially for nonlinear structures. The force tracking performance of the proposed methods is evaluated for a small‐scale steel mass block system with a magneto‐rheological damper subjected to various target forces. Accuracy, time delay, and resonance response of these methods are discussed along with their force control performance for an axially stiff member. Overall, a satisfactory force tracking performance was observed by using the proposed force control methods.     

Seismic performance of buildings retrofitted with nonlinear viscous dampers and adjacent reaction towers

An effective strategy of seismic retrofitting consists of installing nonlinear viscous dampers between the existing building, with insufficient lateral resistance, and some auxiliary towers, specially designed and erected as reaction structures. This allows improving the seismic performance of the existing building without any major alteration to its structural and nonstructural elements, which makes this approach particularly appealing for buildings with heritage value. In this paper, the nonlinear governing equations of the coupled lateral‐torsional seismic motion are derived from first principles for the general case of a multistory building connected at various locations in plan and in elevation to an arbitrary number of multistory towers. This formulation is then used to assess the performance of the proposed retrofitting strategy for a real case study, namely, a 5‐story student hall of residence in the city of Messina, Italy. The results of extensive time‐history analyses highlight the key design considerations associated with the stiffness of the reaction towers and the mechanical parameters of the nonlinear viscous dampers, confirming the validity of this approach.     

Modeling spatially correlated spectral accelerations at multiple periods using principal component analysis and geostatistics

Regional seismic risk assessments and quantification of portfolio losses often require simulation of spatially distributed ground motions at multiple intensity measures. For a given earthquake, distributed ground motions are characterized by spatial correlation and correlation between different intensity measures, known as cross‐correlation. This study proposes a new spatial cross‐correlation model for within‐event spectral acceleration residuals that uses a combination of principal component analysis (PCA) and geostatistics. Records from 45 earthquakes are used to investigate earthquake‐to‐earthquake trends in application of PCA to spectral acceleration residuals. Based on the findings, PCA is used to determine coefficients that linearly transform cross‐correlated residuals to independent principal components. Nested semivariogram models are then fit to empirical semivariograms to quantify the spatial correlation of principal components. The resultant PCA spatial cross‐correlation model is shown to be accurate and computationally efficient. A step‐by‐step procedure and an example are presented to illustrate the use of the predictive model for rapid simulation of spatially cross‐correlated spectral accelerations at multiple periods.