Experimental investigation on a two-part underwater towed system

An experimental set-up is developed and proved to be effective for laboratory study of an underwater towed system. The experimental technique gives a practical method for monitoring the kinematic and dynamic performance of an underwater towed system in a ship towing tank. Both the theoretical and experimental results in the investigation indicate that the hydrodynamic response of a towed vehicle to the wave induced motion of a towing ship can be significantly reduced by applying a two-part tow method. A comparison of the numerical and experimental results in the investigation demonstrates that the numerical simulation results are close to the experimental data, overall agreement between experimental and theoretical results is satisfactory. The results qualitatively verify the mathematical model of a two-part underwater towed system proposed by Wu and Chwang [Wu, J., Chwang, A.T., 2000. A hydrodynamic model of a two-part underwater towed system. Ocean Engineering 27 (5), 455–472].     

GPS数据采集技术及其在海洋调查中的应用

本文应用VB6．0开发了智能化的GPS数据采集软件．对该软件的功能进行了简单的介绍，同时对一些关键技术作了较详细的描述。利用该软件、GPS接收机及PC机的组合，可对走航式测量仪器(或移动设备)进行实时定位并保存定位记录，且大大减少一些不必要的数据，使得软件更为实用。     

A New Fall-Rate Equation for T-5 Expendable Bathythermograph (XBT) by TSK

The accuracy of the manufacturer’s fall-rate equation for the T-5 Model of expendable bathythermograph (XBT) has been investigated based on about 300 collocated pairs of XBT-CTD (Conductivity-Temperature-Depth profiler) measurements in various climatological regions. We found that the equation systematically overestimates depth by about 5% for the T-5 produced by Tsurumi Seiki, Co. Ltd. (TSK), but almost no bias is associated with the T-5 produced by Sippican, Inc., in USA. The cause of this difference is not clear, because the two manufacturers’ T-5 probes are reported to have identical shape and weight in water. We propose a new fall-rate equation for the TSK T-5: z(t) = 6.54071t - 0.0018691t ², where z(t) is depth in meters at time, t, in seconds.     

塔里木盆地的构造演化

从地震大剖面显示，塔里木盆地发育为手风琴式的演化史。大体上形成有3层“断-坳”结构：①震旦系的“断”，古生界-三叠系的“坳”；②侏罗系的“断”，上白垩系的“坳”；③古近系的“断”，新近系的“坳”。断陷与坳陷分别由拉张与挤压应力场所致，这种应力场的变化是由相邻洋壳板块俯冲倾角由小到大的变化所引起的。由于地壳的多旋回运动，多次发生构造沉积演变，构成了多套生储盖组合，多领域、多种圈闭类型的油气藏，从震旦系-古生界-中生界-新生界，各断陷-坳陷结构的盆地都有可能形成油气藏的地质条件。     

土工布充砂袋的应用及其研究进展

对土工布充砂袋技术和国内外的应用进行了介绍。鉴于土工布充砂袋属于一种新兴起的土工新材料和新技术，在设计和工程实际中还存在着许多急待解决的问题，着重对各种典型状态和典型环境下的土工布充砂袋的变形、应力和土工布充砂袋堆的稳定性研究进展进行综述，最后提出进一步研究的思路。     

Recorder-Dependent Temperature Error of Expendable Bathythermograph

The accuracy of temperature measurement by the expendable bathythermograph (XBT) is examined for five types of recorders by comparison with co-located CTD measurements and statistical analysis of temperature profiles including an isothermal layer. A positive temperature error increasing downward is occasionally detected for two types of Japanese recorder which have been commonly used among Japanese oceanographic institutions and marine observatories. This error resembles to that reported by Bailey et al. (1989) and Wright (1991) for a different type of recorders, although its cause is not clearly understood. The irregular occurrence of the error suggests that the problem is not solely due to the recorders but rather by some inconsistency of the whole measuring system including them, an XBT probe and sea water. The error is estimated to increase at a rate of O (0.1°C/100 m), and it could be close to 1°C at the deepest part of the profiles (760 m for Tsurumi T-7). This revised version was published online in July 2006 with corrections to the Cover Date.     

ASM1中污水水质参数与化学计量系数的估测

简要介绍了活性污泥1号模型中14个污水水质参数与5个化学计量系数的估测方法和典型取值。     

Mean flow and variability in the southwestern East Sea

The Ulleung Basin is one of three deep basins that are contained within the East/Japan Sea. Current meter moorings have been maintained in this basin beginning in 1996. The data from these moorings are used to investigate the mean circulation pattern, variability of deep flows, and volume transports of major water masses in the Ulleung Basin with supporting hydrographic data and help from a high-resolution numerical model. The bottom water within the Ulleung Basin, which must enter through a constricted passage from the north, is found to circulate cyclonically—a pattern that seems prevalent throughout the East Sea. A strong current of about 6 cms⁻¹ on average flows southward over the continental slope off the Korean coast underlying the northward East Korean Warm Current as part of the mean abyssal cyclonic circulation. Volume transports of the northward East Korean Warm Current, and southward flowing East Sea Intermediate Water and East Sea Proper Water are estimated to be 1.4 Sv (1 Sv=10⁻⁶ m³ s⁻¹), 0.8 Sv, and 3.0–4.0 Sv, respectively. Deep flow variability involves a wide range of time scales with no apparent seasonal variations, whereas the deep currents in the northern East Sea are known to be strongly seasonal.     

东亚岛弧地形横剖面与板块运动

通过对东亚岛弧横剖面形态的系统分析，并结合弧前的构造应力的分析，作者认为，东亚岛弧形成于板块东移的构造环境中，横剖面形态存在两种基本类型即内缓外陡型和内陡外缓型，这两种不同的横剖面具有不同的弧前应力，前者表现弧前挤压，后者表现弧前引张，这反映地貌形态与构造应力之间的密切关系。     

Regression Formulations for the Stress at Hot Spot of Multiplanar Tubular DT Joints

- Stress concentration analysis of multiplanar tubular DT joints plays an important role in the fatigue design of offshore platforms. A semi-analytic method for stress analysis under the condition of any loads is briefly introduced in the paper. Nineteen multiplanar tubular DT joints with one of two braces of the same dimension subjected to axial loads and out- of- plane bending moments are computed for parametric stress analysis by using the present method. The influence of geometrical parameters on the stresses of multiplanar tubular DT joints is discussed and compared with corresponding uniplanar T joints. The regression formulae for the stress at hot spot of multiplanar DT joints are found by modification of SCF of corresponding uniplanar T joints. The parametric formulae for the maximum stress by superposition. Finally, the influences of stiffening effect and load-interaction effect on the maximum stress of DT joints are discussed.