准噶尔盆地腹部地区生烃增压定量化评价——东道海子北凹陷为例

目前准噶尔盆地腹部地区超压演化过程仅提供了相对时间、概念、定性的认识,并未达到定量化。本文以东道海子北凹陷为例,基于流体包裹体、单井一维和剖面二维烃源岩成熟生烃史模拟技术,采用生烃增压模型定量化评价了侏罗纪八道湾组顶部和底部烃源岩的生烃增压演化过程。研究结果表明侏罗纪八道湾组为东道海子北凹陷主力烃源岩,具有幕式排烃的特点。八道湾组底部烃源岩经历了3 次超压增加和两次超压释放的过程,顶部烃源岩经历了两次超压增加和一次超压释放的过程。八道湾底部烃源岩3 次超压增加的时间分别为距今170～70 Ma、55～23 Ma、10～0 Ma,对应最大压力系数均为2.0,最大剩余流体压力50 MPa,两次超压释放的时间分别为70～55 Ma、23～10 Ma;八道湾组顶部烃源岩两次超压增加的时间分别为130～40 Ma、23～0 Ma,对应流体最大压力系数最大亦可达2.0 左右,最大剩余流体压力44 MPa,超压释放的时间为40～23 Ma。     

滇西芦子园远程矽卡岩Pb-Zn-Fe(Cu)多金属矿床流体包裹体初探及矿床成因探讨

滇西镇康芦子园是"三江"成矿带保山地块内迄今发现的唯一超大型Pb-Zn-Fe(Cu)多金属矿床,是区内系列同类层控热液铅锌矿床的典型代表。矿体呈似层状、脉状及透镜状产于寒武系碳酸盐岩建造的矽卡岩和大理岩层间破碎带,矿石构造以条带状、浸染状和脉状-网脉状为主要特征;围岩蚀变复杂、分带明显,由下至上依次为石榴子石-透辉石-透闪石-阳起石化带→绿泥石-绿帘石-阳起石-蔷薇辉石化带→碳酸盐-大理岩化带。矿床成矿流体从早期到晚期经历了多个矿化阶段。本文选取了该矿床早矽卡岩阶段、晚矽卡岩阶段、石英硫化物阶段和石英碳酸盐阶段的多种脉石矿物及闪锌矿进行了系统的流体包裹体研究。结果显示,早矽卡岩阶段发育微溶CO_2富液相和纯液相水溶液包裹体,并含大量K~+、Na~+、Ca~(2+)、F~-和Cl~-和少量SO_4~(2-),气相成分主要为H_2O、CO_2及少量CH_4和N_2,包裹体均一温度为233.6~315.6℃,盐度为10.6%~17.6%NaCleqv;晚矽卡岩阶段发育含CO_2和子矿物三相包裹体,均一温度214.9~388.0℃,盐度5.9%~16.4%NaCleqv;石英硫化物阶段发育含CO_2的水溶液包裹体,气相成分为CH_4、H_2O和少量CO_2,均一温度150.0~285.0℃,盐度为2.5%~13.8%NaCleqv;石英碳酸盐阶段为单一成分的水溶液包裹体,均一温度为105.0~187.5℃,盐度为0.5%~12.3%NaCleqv。结合H-O同位素研究表明,成矿流体最初来源于具中高温、中高盐度、高K、Na,富CO_2、Cl、F等特征的深部岩浆热液,在石英硫化物阶段开始有大气降水混入,演化为中阶段中低温、低盐度、贫CO_2的热液流体,至成矿晚阶段转化为以大气降水占主导。该矿床成矿环境的改变、流体混合以及流体的沸腾作用可能是导致成矿物质富集沉淀的重要机制。综合矿床地质特征、成矿流体包裹体和HO同位素研究认为,该矿床为与陆陆碰撞造山和深部隐伏岩体有关的远程矽卡岩成矿系统。     

北衙金矿多期热液成矿作用识别:来自地质、岩相学、流体包裹体和H-O-S同位素证据

北衙超大型金矿床是三江特提斯成矿域中喜山期斑岩-矽卡岩型矿床的典型代表,长期以来大量研究均围绕斑岩-矽卡岩成矿作用开展并取得了丰硕成果,然而对于北衙金矿是否存在多期热液成矿作用尚不明确。本次研究基于详细野外调查、岩相学与矿相学研究,流体包裹体显微测温及成分分析、H-O-S同位素分析等多种手段,识别了北衙金矿成矿晚期存在新一期热液成矿事件。主要证据如下:(1)野外调查发现北衙金矿发育NW向陡倾断裂控制的石英多金属硫化物脉,其切割矽卡岩矿体与矽卡岩晚期石英硫化物矿脉;(2)本次研究矿脉中原生流体包裹体类型主要为富CO_2三相水溶液包裹体、含CO_2三相水溶液包裹体及气液两相水溶液包裹体,而矽卡岩晚期硫化物脉中除上述三种类型外还发育含子晶三相水溶液包裹体;(3)成矿流体均一温度分布范围为204～426℃,盐度为1.0%～14.2%NaCleqv,整体表现为中高温、中低盐度的NaCl-CO_2-H_2O流体体系,而矽卡岩晚期硫化物脉成矿流体体系具有中温、中高盐度的特征;(4)该矿脉中石英的δ~(18)O、δD范围分别为7.5‰～9.4‰与-102.0‰～-75.0‰,指示岩浆水来源,而矽卡岩晚期硫化物脉具有岩浆水和大气水混合来源。本次研究的多金属硫化物矿脉δ~(34)S值范围为-0.97‰～1.40‰,与矽卡岩期和矽卡岩晚期硫化物脉中黄铁矿S同位素一致,表明多期矿化成矿物质均具有幔源贡献。结合北衙矿集区成岩成矿动力学背景,推测始新世大规模地壳拆沉、软流圈上涌导致的强烈的壳幔相互作用可能是北衙金矿多期成矿作用的诱因。     

北京及邻近地区中等以上地震地下流体异常识别与特征研究

系统分析了北京及其邻区多年积累的震例资料, 提出该区的地下流体异常分为趋势上升型中期异常、 转折型中短期异常、 突发型短期异常和短临异常等类型。 运用“同一化”思路、 从属函数、 剩余曲线及原始曲线均方差等异常判定方法, 提取了中等以上地震, 特别是5级以上地震的中、 短、 临异常实例。 通过对流体异常特征的统计分析, 给出了北京及邻近地区的中期、 中短期、 短期和短临异常的时间分布特征, 并对地震前各阶段异常的超前时间进行了总结, 该时间可作为发震时间的预测指标。 在实际应用中可为该区的震情判定提供依据。     

有机质热演化过程中地层压力的作用与影响

压力对有机质演化的影响长期以来争论不断,共有3种不同意见：压力对有机质演化没有影响,压力促进有机质的演化,压力抑制有机质的演化。通过对前人所做实验的实验设备、实验样品及实验结果的分析对比发现：不同实验结果主要是由于不同实验条件引起的,特别是实验系统和加压方式的不同,对实验结果影响最大,所代表的地质意义也不同。综合分析结果表明,当压力的增加表现为沉积有机质受到的有效应力增加时可以促进有机质生烃;当压力的增加表现为孔隙流体压力增加时,有机质生烃过程将受到抑制;另外,这两种情况都可能使干酪根的镜质组反射率降低,易使人得出压力增加抑制有机质演化的结论。进一步对压力影响有机质演化的成因机制进行了分析,发现在有机质演化的不同阶段因异常压力的增压机制不同,压力在有机质演化过程中所表现出来的作用也有差异。     

青城子小佟家堡子、林家金矿成矿流体特征及成矿机制

小佟家堡子、林家金矿是青城子铅锌、金、银矿集区的中-大型金矿床,金矿床与沉积-变质期硅化岩关系密切。通过与矿区尖山岩体、新岭岩体中流体包裹体对比研究表明,金矿床与尖山岩体中主要发育水溶液包裹体,极少量的CO2包裹体、含CO2三相包裹体,而新岭岩体除发育以上包裹体外,还发育含子矿物多相包裹体。测温结果显示金矿床成矿流体温度为110～335℃,盐度3．9％～16．2％NaClrq拉曼光谱分析表明金矿床流体成分以H2O为主,少量的CO2、CH4等气体,表明成矿流体属NaCl-H2O体系。金矿床与尖山岩体中流体包裹体温度、盐度及成分相近,推断成矿流体主要来自沉积-变质期。     

基于CFD的单个建筑物风场模拟参数选择

运用流体力学软件FloEFD对沽源单个建筑物周围的风场进行数值模拟。通过不断改变模型中计算参数的设置进行一系列模拟试验,对比模拟试验结果,并与观测资料进行比较,分析不同计算参数对模拟结果的影响,并获得适用于该模型的最佳参数。主要研究的计算参数包括计算域高度,初始网格等级,局部初始网格等级和不同平均风速剖面形式。结果表明:计算域高度从3倍建筑物高度开始,空腔区的长度、漩涡中心位置以及再发展区的边界位置基本保持稳定。随着初始网格等级的增加,空腔区的长度、再发展区的边界位置及计算时间逐渐增大。局部初始网格等级对模拟结果影响不显著。以两种不同平均风速剖面形式进行模拟,迎风漩涡长度不同,背风面影响不大。与观测资料比较显示,最优参数组合为:计算域高度为3倍建筑物高度,初始网格等级为4、局部初始网格等级为4、平均风速剖面形式为指数律。     

A critical CAE analysis of the bottom shape of a multi stepped air cavity planing hull

One of the most important aspects, in the ACS and multi stepped hull design, is the choice of the geometrical shape of the cavity and the steps. In this article a complete experimental and numerical campaign on a multi stepped ACS has been carried out, varying the velocity and the air flow rate under the hull. The experimental tests have been conducted in an ITTC Towing Tank allowing to validate the numerical simulations obtained by means of a CFD U-RANSe (Unesteady Reynolds Averaged Navier-Stokes equations) code. The CFD setup is described in detail. From this campaign a critical analysis of the Froude number influence on the air cushion shape has been argued. The authors identified four different behaviours, from low to very high Froude numbers. The use of CFD has allowed to observe quantities of difficult evaluation by means of traditional experimental test, as e.g. the frictional component of the resistance, the airflow path lines and the volume of fraction in transversal and longitudinal sections. The results have been discussed.     

Interaction mechanisms among waves,currents and a submerged plate

Wave-induced loads on a submerged plate, representative of submerged breakwater, coastal-bridge deck and a certain type of wave energy converter, in a uniform current are investigated in this study using fully nonlinear numerical wave tanks (NWTs) based on potential flow theory. The coupling effect of wave and current is explored, and the underlying interaction mechanisms of the hydrodynamic forces are described. The presence of a background current modifies the frequency dispersion. It produces changes of the water-surface elevation, and also has an effect on wave-induced loads. Depending on the nonlinearity, higher harmonic wave components are generated above the submerged plate. These contribute to the wave forces. It is found that the horizontal and the vertical force, hence the moment, are affected in the opposite way by the currents. The Doppler shifted effect dominates the vertical force and the moment on the plate. Whereas, the Doppler shifted effect and the generation of higher wave harmonics play opposite roles on the horizontal forces. The contribution of 2^nd order harmonics is found to be up to 30% of the linear component. The current-induced drag force, represented by the advection term ρU∂φ/∂x in the pressure equation, is found to lead to a decrease in the moment for the most range of wavelengths considered, and an increase in the moment for a small range of longer waves.     

Performance of pile-restrained flexible floating breakwaters

The overall performance of pile-restrained flexible floating breakwaters is investigated under the action of linear monochromatic incident waves in the frequency domain. The aforementioned floating breakwaters undergo only vertical structural deflections along their length and are held in place by means of vertical piles. The total number of degrees of freedom equals the six conventional body modes, when the breakwater moves as a rigid body, plus the extra bending modes. These bending modes are introduced to represent the structural deflections of the floating breakwater and are described by the Bernoulli–Euler flexible beam equation. The number of bending modes introduced is determined through an appropriate iterative procedure. The hydrostatic coefficients corresponding to the bending modes are also derived. The numerical analysis of the flexible floating breakwaters is based on a three-dimensional hydrodynamic formulation of the floating body. A parametric study is carried out for a wide range of structural stiffness parameters and wave headings, to investigate their effect on the performance of flexible floating breakwaters. Moreover, this performance is compared with that of the corresponding pile-restrained rigid floating breakwater. Results indicated that the degree of structural stiffness and the wave heading strongly affect the performance of flexible floating breakwaters. The existence of an “optimum” value of structural stiffness is demonstrated for the entire wave frequency range.