岩石巴西圆盘试验中的空间拉应力分布

指出目前人们使用了40多年的岩石巴西圆盘试验拉伸强度公式来自二维弹性力学解答,该公式不适用于实际情况所对应的三维弹性力学问题。为了得到三维条件下试样内部的应力分布规律,采用三维有限元分析软件Marc对试样进行了弹性受力分析,结果表明,试样横截面上的拉应力分布规律与二维条件下的情况相类似,但横截面上的应力值沿试样厚度方向是有变化的,越靠近两端面,水平拉应力越大。分析发现,对于高径比为1、泊松比为0.25的巴西圆盘试样,按二维公式计算的抗拉强度比真实值小23.3 %     

边坡治理工程的数值模拟研究

边坡作为地质体，往往具有复杂的结构和地质力学特征，这些特点在一般的边坡治理工程设计中往往难以全面反映。本文结合实际工程，介绍了在较全面考虑边坡质体上述特性的前提下，采用数值模拟方法对边坡治理工程所进行的方案论证和设计优化。     

建筑物地基不均匀震陷有限元时程分析方法

根据建筑物不均匀震陷发生机制,提出了建筑物不均匀震陷二维有限元分析方法。采用了不规则荷载下土的残余应变模型及土体逐步软化模型,考虑了土、结构及地震动波形对不均匀震陷的协同作用效果,实现了对建筑物不均匀震陷的时程分析,并通过大型振动台试验对方法的可靠度进行了检验。     

Mechanism and countermeasures of preceding tunnel distortion induced by succeeding EPBS tunnelling in close proximity

Twin tunnels are frequently used to address the increasing transportation demands in large cities. To ensure the safety of twin tunnels in close proximity, it is often necessary to take protective measures that have not been well studied. Field monitoring was conducted for a project of twin earth pressure balance shield (EPBS) tunnels in typical soft ground. The preceding tunnel was reinforced by various measures, including trailer bracing, compensation grouting, artificial freezing and scaffold bracing. The entire deformation of the reinforced tunnel was recorded during the succeeding tunnelling process. A three dimensional finite-element method (FEM) model was established to simulate the entire process of twin EPBS tunnelling, particularly the reinforcement measures. The computed deformations of the reinforced tunnel were consistent with the measured data. Furthermore, the stress history and pore pressure of the surrounding soil were analysed to investigate the deformation mechanism of the tunnel. Both the measured and computed results indicate that although the face pressure of the succeeding tunnel was smaller than the earth pressure at rest, the preceding tunnel could still experience an inward horizontal convergence and a deflection away from the succeeding tunnel. These distortion modes were caused by the squeezing effect of the horizontal soil arch in front of the succeeding tunnel face. Finally, convergence and deflection indices were proposed to quantify and assess the effectiveness of the reinforcement measures. The trailer bracing, as an “in-tunnel” reinforcement technique, was found to be the most effective method for controlling tunnel convergence. However, artificial freezing as an “out-tunnel” reinforcement technique led to the largest reductions in tunnel deflection. A combination of both “in-tunnel” and “out-tunnel” reinforcements was recommended.     

一种简单的网格图形局部放大技术

本文利用视口技术，根据坐标平移的原理，设计出一个用于有限元网格图局部放大的程序，并在微机上调试运行通过，本方法亦可应用于其他类型的曲线图放大。     

Numerical Analyses of Bearing Capacity of Deep-Embedded Large-Diameter Cylindrical Structure on Soft Ground Against Lateral Loads

1 .IntroductionThe large-diameter cylindrical structure for coastal and offshore engineering has been widely usedin China .Thistype of structureis composed of a steel or reinforced concrete cylindrical thin-wall shellplaced partlyintothe ground by a speci…     

粗粒料多边形表征及二维FEM/DEM分析

考虑到颗粒形状对粗粒料的力学特性有重大影响,提出了一种新的表征颗粒形状的方法,即在椭圆上随机选取一系列点连接成多边形颗粒,表征狭长扁平的颗粒。新方法较圆上取点的方法能代表更多类型的颗粒形状,适用范围更广。提出了一种新的粗粒料投放算法,即先缩小颗粒,然采用随机算法将缩小的颗粒投放至给定区域,对颗粒划分好网格后,将颗粒放大到原来的大小,然后采用有限元-离散元(FEM/DEM)方法计算稳定后即生成了相应的试样。通过将上述颗粒生成及投放算法与FEM/DEM结合,应用于粗粒料的数值模拟。分析表明,FEM/DEM是研究粗粒料力学性质的较好方法,对复杂的颗粒形状也可简单建模,且因在颗粒内部划分了有限元网格,复杂的接触判断及接触力计算转化为标准统一的三角形和三角形之间的接触判断及接触力计算,所有的计算均可标准化、统一化。同时因为颗粒是可以变形的,依然保留了连续介质力学中应力和应变的概念,无须像PFC那样需通过测量圆来间接表示某点的应力、应变。最后,通过粗粒料的侧限压缩试验的数值模拟,展现了文中提出的一整套解决方案在模拟粗粒料方面的巨大潜力。     

云南天文台1m红外望远镜的主镜热力学分析

云南天文台1m红外太阳望远镜是多功能、多波段的太阳望远镜,望远镜使用过程中主镜的热变形直接关系这系统的光学精度,建立光学系统的光机热结合的分析方法,可以直观的得到热辐射对光学系统的影响结果,使得望远镜的设计阶段就能评估热变形对系统的精度影响,确定光学元件是否满足要求.     

挡墙加固非饱和土边坡整体稳定性分析

在对挡墙加固边坡进行设计和评价时应综合考虑基质吸力和挡墙对边坡整体稳定性的影响。应用可以考虑基质吸力的弹塑性强度折减有限元程序,分析了挡墙加固非饱和土边坡的整体稳定性,揭示了基质吸力对加固边坡整体稳定性的影响程度,同时亦分析了整体潜在滑动面位置的变化情况,并进行了关于吸力摩擦角的敏感性分析。     

一种有限元转化为颗粒离散元的方法及其应用研究

为了充分发挥有限元与颗粒离散元各自的优势,提出了一种由有限元转化为颗粒流的方法。数值模型首先用较粗的有限元网格进行离散,并在单元上引入连续介质本构模型。力学计算开始后,实时跟踪各单元的应力状态。一旦某单元的应力满足Mohr-Coulomb准则或最大拉应力准则,删除该单元,同时创建具有一定数目、随机分布且微嵌入的颗粒簇。其后,该单元所在区域的非连续变形及失稳断裂由颗粒簇演化获得。各颗粒的质量、材料参数、速度、位移、接触力等信息根据插值从有限元单元中继承。为了实现有限元与颗粒流接触面的耦合计算,引入了点-棱（二维）及点-面（三维）接触模型,通过法向及切向弹簧实现接触力的计算。颗粒球与有限元板的碰撞分析、单轴压缩、岩石切割等案例展示了上述方法的精确性及合理性。