覆盖型岩溶塌陷的空间预测与评价

针对危害性最大的覆盖型岩溶,建立考虑土盖层厚度和岩土体类型的典型岩溶地质结构模型,分析其在地下水位升降及地表水入渗情况下的塌陷机制。结合具体岩溶工程问题,提出“物理探测－工程勘察－岩、土物理力学试验－数值模拟－监测评价”的岩溶塌陷空间预测方法,并将该方法应用于湖北省黄石市一处典型覆盖型岩溶灾害区。在物理勘探、工程勘察和岩土物理力学试验的基础上进行的岩溶塌陷数值模拟表明,相对于地下水位快速升降,因地表水入渗导致黏土盖层软化引起的地面沉降更大。依据数值模拟结果,结合研究区地面及房屋裂缝的发展情况,划分出塌陷危险区的具体空间范围。实践证明,该岩溶塌陷空间预测方法具有较强的可操作性和较高的可靠性,可作为类似工程问题的研究方法予以推广     

高应力深部洞室模型试验分区破裂现象机制的初步研究

以经典的芬纳公式为手段,以观察到分区破裂现象的模型试验为背景,通过对简化后的圆形巷道围岩应变场和能量场的分析,发现极限平衡区边界存在径向应变的不连续性和弹性变形能的聚集性。认为与开挖洞室呈同心圆的环状断裂的形成,是极限平衡区在边界上由于应变场的不协调而导致的与弹性区的断裂分离。而分区破裂的产生,则是这种断裂分离形成后极限平衡区向深处发展的结果。解释了分区破裂产生时洞周围岩应变和位移随距离洞室增加呈波浪形变化的非单调性规律,给出了分区破裂形成后各破裂区半径的表达式,关系式表明各破裂区之间存在等比关系,比值与地应力状态及围岩力学参数有关。将分区破裂模型试验的参数代入该式,可得,n =1.1左右,与实验完成后剖开模型的各破裂区分布特征基本相符。     

公路隧道通风竖井岩爆机制颗粒流模拟研究

根据工程地质资料分析,岩爆是秦岭公路隧道2号通风竖井施工过程中的主要难题。岩爆机制是指岩爆发生的物理过程,与岩石的颗粒大小、颗粒胶结和粒间孔隙等结构特征密切相关。根据颗粒流基本理论和竖井混合片麻岩的基本力学特性,进行混合片麻岩细观颗粒参数标定研究。颗粒大小不是一个自由参数,通过颗粒流模拟的相似比分析,采用强度折减方法进行竖井岩爆机制的颗粒流模拟。研究表明,岩爆孕育的细观机制为平行于开挖面的微裂纹萌生-微裂纹扩展、聚合-宏观裂纹的形成,为压致张剪断裂破坏,主要是由张拉裂纹扩展、聚合引起的,是一个渐近破坏过程。研究成果为竖井岩爆稳定性分析提供初步依据。     

采空侧巷道底鼓形成机制与防治技术研究

煤矿深部采空侧巷道底鼓现象日趋普遍和严重,严重影响巷道的运输和正常使用,其底鼓防治技术研究已成为目前煤矿岩石力学问题研究的重点。通过理论分析、数值模拟、现场试验等研究方法,对采空侧巷道底鼓的特征、形成原因、形成机制及其防治技术进行了详细研究,得到以下结论：（1）采空侧巷道底鼓与底板岩性和底板岩层的应力重新分布有关;（2）底板在严重挤压变形的情况下发生断裂,底板隆起,墙角发生外移是造成底鼓的主要原因;（3）底鼓始于巷道底角与底板中部;（4）采用中空锚杆注浆与高强锚杆锚注联合支护技术能有效治理采空侧巷道的底鼓     

EXPERIMENTAL STUDY OF TEMPERATURE EVOLUTION AND IDENTIFICATION OF INSTABILITY POSITION OF PLANAR STRIKE-SLIP FAULT DURING PROCESS OF STICK-SLIP

Stick-slip of fault in laboratory accompanies change of temperature. Temperature change is not only concerned with sliding friction, but also with the stress state of the sample. In this article, we use infra-red thermal imaging system as wide-range observation means to study the temperature variation of different stages during the deformation of sample. The rock sample for the experiment is made of granodiorite from Fangshan County with a size of 300mm×300mm×50mm. It is cut obliquely at an angle of 45°, forming a planar fault. Two-direction servo-control system was used to apply load on the sample. The load in both directions was forced to 5MPa and maintained constant (5MPa) in the X direction, then the load in the Y direction was applied by a displacement rate of 0.5μm/s, 0.1μm/s and 0.05μm/s successively. The left and below lateral of the sample were fixed, and the right and top lateral of the sample were slidable when loaded. The experiment results show not only the temperature change from increase to decrease caused by conversion of stress accumulation to relaxation before and after the peak stress, but also opposite variation of temperature increase on fault and temperature decrease in rock during instability stage. Most important of all, we have found the temperature precursor identifying the position of instability through the temperature variation with time along the fault. It shows that rate of temperature increase of instability position keeps relative high value since the stage of strongly off-linear stage, and accelerates in stage of meta-instability. After separating the effect of friction and stress, we found that temperature increase occurs in the rock near the fault instead of on the fault, which means the mechanism of temperature increase is stress accumulation. Temperature of fault at the instability position does not increase, which means the position is locked. We speculate that the position of locked area on fault with high stress accumulation near the fault may be the future instability position. It is of significance of studying temperature variation during stick-slip to the monitoring of earthquake precursors. Heat caused by friction of earthquake needs long time to transfer to the surface and could not be detected as a precursor. While the stress of surface rock near the fault would change as the stress of interior rock changes, which could cause detectable temperature variations. The research purpose of this article is to find special change positions before instability. As the temperature variations are caused by stress and slip of fault, the results are also meaningful to analysis of stress and displacement data related to earthquake precursors.     

黏性土坡地震失稳机制及其在黄土斜坡地震稳定性分析中的应用

基于地震作用下黏性土坡失稳滑动特点,以土体应力状态及其变化分析边坡失稳过程。通过分析地震作用下边坡不同部位土体应力状态和剪应力变化,结合实际地震边坡失稳破坏特征,提出黏性土坡地震三段式滑动失稳机制。在分析该滑动失稳机制与有限元强度折减法之间应力关联的基础上,将两者结合应用于实际黄土地震滑坡动力稳定性分析。依据此考虑得到的动力安全系数相比较其他方法,与极限平衡法得到的结果更为接近。     

MECHANISM OF THE 2015 PISHAN,XINJIANG, MS6.5 MAINSHOCK AND RELOCATION OF ITS AFTERSHOCK SEQUENCES

Using the digital broadband seismic data recorded by Xinjiang network stations, we obtained focal mechanism of the July 3 Pishan, Xinjiang, M_S6.5 earthquake with generalized Cut and Paste(gCAP)inversion method. The strike, dip and rake of first nodal plane are 97°, 27°, 51°, and the second nodal plane are 318°, 70°, 107°. The centroid depth and moment magnitude are calculated to be 12km and 6.4. Combining with the distribution of aftershocks, we conclude that the first nodal plane is the seismogenic fault, and the main shock presents a thrust earthquake at low angle. We relocated 1014 earthquakes using the double-difference algorithm, and finally obtained 937 relocated events. Our results show that the earthquake sequences clearly demonstrate a unilateral extension about 50km nearly in NWW direction, and are mainly located above 25km depth, especially the small earthquakes are predominately located at the shallow parts. Furthermore, the focal depth profile shows a southwestward dipping fault plane at the main shock position, suggesting listric thrust faulting, which is consistent with the dip of the mainshock rupture plane. The spatial distribution of aftershocks represents that the Tarim block was thrust under the West Kunlun orogenic belt. In addition, the dip angle of the fault plane gradually increases along the NWW direction, possibly suggesting a gradual increase of strike-slip component during the NWW rupturing process. From above, we conclude that the Pishan M_S6.5 earthquake is the result of Tibet plateau pushing onto the Tarim block from south to north, which further confirms that the continuous collision of India plate and Eurasia plate has strong influence on the seismic activity in and around the Tibet plateau.     

CHANGES IN FAULT MOVEMENT PROPERTY AND GENETIC MECHANISM ON THE WESTERN SEGMENT OF THE XIANGSHAN-TIANJINGSHAN FAULT ZONE

The Xiangshan-Tianjingshan fault zone is an important part of the arc tectonic zone in northeastern Tibet, whose eastern segment is characterized by primarily left-lateral slip along with thrust component. In contrast, the fault movement property on the western segment of the Xiangshan-Tianjingshan fault zone is more complicated. According to the offset geomorphic features and cross sections revealed by the trenches and outcrops, the western segment is mainly a left-lateral strike-slip fault with normal component, and only accompanied with reverse component at specific positions. To determine the genetic mechanism of fault movement property on the western segment, we obtained three main factors based on the integrated analysis of fault geometry:(1)Step-overs:the left-stepping parallel faults in a sinistral shear zone create extensional step-overs and control the nearby and internal fault movement property; (2)terminal structures:they are conductive to stop rupture propagation and produce compressive deformation at the end of the fault trace; and(3)double bends:strike-slip faults have trace that bends such that slip between two adjacent blocks creates a compressive stress and thrust fault. Additionally, the Tianjingshan sub-block moves to SEE and creates an extensional stress at the end of the sub-block associated with normal faults. It shows that the Xiangshan-Tianjingshan fault zone has a complex evolution history, which is divided into two distinctive periods and characterized by laterally westward propagating.     

2012和2013年广东新丰江锡场2次MS4.8地震发震构造的确定*

利用广东新丰江锡场2012和2013年2次M_S4.8地震震中附近的2009年1月至2015年6月精定位小震资料,依据小震丛集发生在大震断层面及附近的原则,采用模拟退火算法和高斯-牛顿算法相结合的方法,反演得到了锡场附近2条相交断层的详细参数及地理分布。NEE向断层F1的走向为78.5°,倾角为87.7°,长度约8.2km,以右旋走滑错动为主;NW向断层F2的走向为137.3°,倾角为87.9°,长度约5.9km,以左旋走滑错动为主。用断层附近M_L3以上地震的震源机制解证明反演结果是可靠的,并由2次4.8级地震的震源机制解判断出各自的发震断层。     

河南范县及邻区地震精定位及震源机制解分析

选取河南范县及邻区2008年1月~2015年9月M_L≥2.0地震78个,用双差定位法进行重新定位。结果显示,重定位的震中主要沿聊城-兰考断裂带呈NE向分布,较此前更集中。重定位后的震源深度82%位于7~8km,也比此前更集中。在此基础上,用CAP方法研究了该地区2008年以来M_L≥3.0地震的震源机制解。结果显示,节面Ⅰ的14个地震中有11个地震震中分布呈NE向,这与用双差法重新定位后的震中分布方向一致。此外,这14个地震中有9个地震的P轴方位在50°~100°,均值为75°,这与华北地区主压应力方向基本一致。综合分析认为,该区域的地震活动与聊城-兰考断裂有关。