全尾砂-废石混合回填膏体流动特性变化规律

质量浓度、废石掺量是影响尾砂-废石混合回填体流动特性的主要因素,研究这些因素对膏体流动性的影响规律,对于控制膏体流动性具有重要意义。采用改进的小型直剪装置进行混合回填体直剪试验,以黏聚力、内摩擦角、抗剪强度为依据,综合得出了混合回填膏体流动性变化规律。试验结果表明,膏体在受力变形前期呈较为明显的似弹性性质,随废石掺量增加,位移-剪应力曲线中阶梯状变化趋势增加;回填体黏聚力取决于质量浓度,内摩擦角受质量浓度和废石掺量影响程度基本相同,两者协同作用;质量浓度在80%～88%范围时,黏聚力随质量浓度增大呈非线性增大,内摩擦角与质量浓度呈S型变化趋势;抗剪强度随质量浓度的增大而增加,在82%～84%区间抗剪强度变化显著,流动性出现突变。     

复合填料热传导过程数值模拟

复合填料由废铸砂、粉煤灰、聚苯乙烯（EPS）颗粒、水泥和水按一定质量比例混合制成,具有低导热性、抗冻胀和轻质特性。根据热阻力法则和比等效导热系数相等法则,将材料视为由大量正方形单元体组成,其中心为一个球形EPS颗粒,这种单元体与总体的导热系数相等。运用AN SY S软件对复合填料单元体的传热过程进行了有限元模拟,根据瞬态法导热系数测试原理,推求不同EPS掺入比情况下的复合填料导热系数,分析EPS颗粒与导热系数的关系,发现材料导热系数随着EPS掺入比的增加而快速降低。将材料导热系数数值模拟与实测结果作比较,发现有限元模拟值与实测值接近,说明采用有限元方法可以实现对材料传热过程的模拟。     

2012年6月30日新疆新源-和静MS6.6地震序列震源机制解?

In this article,we use the CAP method to invert the focal mechanism of Xinyuan-Hejing M S6. 6 earthquake on June 30,2012. Our result shows that the best double couple solution of the M S6. 6 event is 299°,68° and 164° for strike,dip and rake angles respectively. The other nodal plane is 35°,75° and 23°. The azimuth and dip angle of the P-axis are 166°and 5°,those of the T-axis are 258° and 26°. The moment magnitude is 6. 3. The estimated focal depth is about 21 km. The predominant rupture direction of this seismic sequence is NWW. The dip angles are between 60° and 90°. The rake angles are in the majority of ± 180°± 30°. The predominant strike of the azimuthal angle of the P-axis is near NS and T-axis is near EW. Preliminary analysis indicates that nodal plane I is the seismogenic fault,which is a NWW-trending,nearly upright left-lateral strike-slip fault.The displacement property,the principal compressive stress of this M S6. 6 earthquake and the P-axis preponderant orientation of this seismic sequence agree with the characteristics of the tectonic stress field of the focal area and its surroundings.     

2013年洱源M_S5.5地震序列M_L≥3.4地震的震源机制解研究

利用云南省地震台网的宽频带数据,采用CAP方法计算了2013年3月3日洱源MS5.5地震前后共10次ML≥3.4地震的震源机制解,分析了洱源MS5.5地震前后震源机制解的一致性变化特征,结合精定位结果、震后现场灾害评估报告及震区地质构造情况,判定维西—巍山断裂以西的苍山西麓炼铁盆地东缘主边界断裂带为洱源MS5.5地震的发震构造,震源机制解节面Ⅱ(走向160°、倾角48°、滑动解-99°)为其发震断层面。     

东乡县湿陷性黄土回填碾压的施工控制措施

针对东乡县湿陷性黄土回填碾压质量要求及控制工序,用运碾压厚度试验、含水率试验、碾压遍数试验、碾压速度试验等,从湿陷性黄土回填碾压的两个控制工序,即黄土回填和黄土碾压出发,全面系统的分析了压实度影响因素并提出了施工控制措施。研究表明,在相同压实条件下,适宜的回填厚度有益提高压实度质量和效益;确定最佳含水率后,在施工中不影响施工质量的前提下,相对扩大土的含水率控制范围,既能达到整体压实稳定,又能加快施工进度;在相同的回填条件下,同一深度的压实度随压实机械功能增大,压实度越高;在相同压实功能条件下,同一深度范围内碾压遍数越多,压实度越高;增加压实功能的办法提高土基强度的效果有一定限度,吨位增加到一定限度以上,效果提高愈为缓慢;碾压速度加倍时,碾压遍数相应加倍,应针对具体碾压材料层和所用压路机,通过铺筑试验区域选择合适的碾压速度。     

无传统换撑条件下的深基坑支护工程

通过工程实例,介绍了在无传统换撑（即地下一层楼板）条件下的一种换撑方案,即采用一排钻孔灌注桩作为挡土结构,坑内设置2道钢筋混凝土内支撑,钻孔灌注桩外侧设置2排深层水泥搅拌桩作止水帷幕,同时可防止淤泥挤入。实际开挖证明该换撑做法是安全、可靠的。     

钢管水泥土围护墙等效弹性模量的有限元计算

分析了水泥土围护墙弹性模量对于控制基坑变形的重要性、根据上海某钢管水泥土墙基坑支护的工程实例建立ABAQUS平面二维有限元模型,计算钢管水泥土围护墙等效弹性模量,量化了内插钢管对提高水泥土重力式围护结构的支护强度所起到的作用,并对钢管长度、外径、间距和插入位置进行了参数分析。     

Determination of passive earth pressure with lower bound finite elements limit analysis and modified pseudo-dynamic method

ABSTRACT

The present study deals with the determination of passive earth pressure under seismic condition by following the lower bound finite elements limit analysis and modified pseudo-dynamic methodology. In accordance with the lower bound finite elements formulation, the stress field was modelled using a three-noded triangular elements, while the passive pressure was determined via linear optimisation. The parametric study was performed, for a vertical rigid retaining wall, by varying the magnitude of seismic acceleration in horizontal direction (k_h) between 0 and 0.3, while the vertical seismic acceleration (k_v) was kept equal to 0 or 0.5 k_h. Furthermore, the damping coefficient for dry cohesionless backfill was kept ξ = 10%. The obtained results in various cases were found to be in good agreement with those found in the literature. It is expected that this method can be further used for solving other important geotechnical stability problems.     

An analytical solution for the nonlinear distribution of effective and total stresses in vertical backfilled stopes

The increasing use of backfill in underground mines requires a proper evaluation of the stress state in and around the filled openings. This is, however, a relatively complex issue due, in part, to the large contrast in strength and stiffness between the backfill material and surrounding rock mass. In recent years, it has been shown that arching theory, based on limit equilibrium analysis, can be used to estimate the stress distribution in backfilled stopes. Nonetheless, many simplifications are involved in such analytical solutions and this affects the precision and significance of the calculated results. In this paper, a previously developed solution is enhanced by introducing the combined effects of non-uniform vertical stress distribution and positive pore water pressure. This leads to a more representative analytical solution, as demonstrated by successful comparisons with numerical simulations. The results indicate that the proposed solution can be used to estimate the effective and total stress state in submerged or partially submerged backfilled stopes with a simple geometry.     

矿渣微细粉掺量对水泥水化产物的影响

利用X射线衍射、TG-DSC综合热分析以及环境扫描电子显微分析技术等,研究了矿渣微细粉对水泥水化产物钙矾石、Ca(OH)₂、CSH凝胶等的影响规律。研究结果表明,在水化早期,矿渣微细粉即参与水泥水化进程,显著影响水泥水化产物钙矾石、Ca(OH)₂和CSH凝胶等的生成速度和生成量及微观形貌,并且随着其掺量增大及水化时间延长,矿渣微细粉参与水泥水化反应程度逐渐提高。