Effects of Wind Fences on the Wind Environment around Jang Bogo Antarctic Research Station

This study investigated the flow characteristics altered by Jang Bogo Antarctic Research Station using computational fluid dynamics(CFD) modeling. The topography and buildings around Jang Bogo Station were constructed with computeraided-design data in the CFD model domain. We simulated 16 cases with different inflow directions, and compared the flow characteristics with and without Jang Bogo Station for each inflow direction. The wind data recorded by the site's automatic weather station(AWS) were used for comparison. Wind rose analysis showed that the wind speed and direction after the construction of Jang Bogo Station were quite different from those before construction. We also investigated how virtual wind fences would modify the flow patterns, changing the distance of the fence from the station as well as the porosity of the fence. For westerly inflows, when the AWS was downwind of Jang Bogo Station, the decrease in wind speed was maximized(-81% for west-northwesterly). The wind speed reduction was also greater as the distance of the fence was closer to Jang Bogo Station. With the same distance, the fence with medium porosity(25%–33%) maximized the wind speed reduction.These results suggest that the location and material of the wind fence should be selected carefully, or AWS data should be interpreted cautiously, for particular prevailing wind directions.     

平台障碍物对海气通量观测影响的数值分析

基于计算流体动力学模型（CFD）模拟了背景风风速为2 m·s-1、4 m·s-1、6 m·s-1下通量观测平台周围的风场分布,确定了不同风速下平台障碍物对观测影响最小的风向范围。发现风速不同,平台对背景风的影响范围不同,风速越大,平台对背景风的影响越大。运用涡动相关法计算不同风向条件下的湍流通量,定量分析由于平台干扰对海气通量计算的影响,发现选取迎风条件下的数据计算得到的海气通量会比实际偏低。     

水平轴潮流能水轮机数值模拟方法对比分析

叶素动量理论和CFD方法是水平轴潮流能水轮机性能分析中运用较为广泛的数值模拟方法,文中结合小尺寸水轮机模型试验,对比分析了叶素动量理论和CFD方法在水轮机性能分析中的准确性和适用性.验证结果表明:叶素动量理论和CFD方法均能对水轮机的性能进行预报,且CFD精度高于动量叶素理论;大尖速比时,动量叶素理论偏离较高,不再适合性能预报;在小尖速比下,建议采用RNGk-ε模型的CFD方法进行分析计算;动量叶素理论适合设计初期设计方案的对比分析,而CFD方法适合对设计结果的验证校核和详细分析.     

Optimization of Blade Motion of Vertical Axis Turbine

In this paper, a method is proposed to improve the energy efficiency of the vertical axis turbine. First of all, a single disk multiple stream-tube model is used to calculate individual fitness. Genetic algorithm is adopted to optimize blade pitch motion of vertical axis turbine with the maximum energy efficiency being selected as the optimization objective. Then, a particular data processing method is proposed, fitting the result data into a cosine-like curve. After that, a general formula calculating the blade motion is developed. Finally, CFD simulation is used to validate the blade pitch motion formula. The results show that the turbine’s energy efficiency becomes higher after the optimization of blade pitch motion; compared with the fixed pitch turbine, the efficiency of variable-pitch turbine is significantly improved by the active blade pitch control; the energy efficiency declines gradually with the growth of speed ratio; besides, compactness has lager effect on the blade motion while the number of blades has little effect on it.     

Numerical and Experimental Studies on the Propulsion Performance of A Wave Glide Propulsor

This paper introduces a newly developed Unmanned Wave Glide Vehicle (UWGV), which is driven only by extracting energy from gravity waves, and presents a comprehensive study on the propulsion performance of the UWGV’s propulsor―Wave Glide Propulsor (WGP) in a regular wave. By simplifying the WGP as six 2D tandem asynchronous flapping foils (TAFFs), a CFD method based on Navier?Stokes equations was first used to analyze the hydrodynamic performance of TAFFs with different parameters of non-dimensional wave length m and non-dimensional wave height n. Then, a series of hydrodynamic experiments were performed. The computational results agree well with the experimental results when n≤0.07 and both of them show the thrust force and input power of the WGP are larger at smaller m or larger n. By analyzing the flow field of TAFFs, we can see that a larger m is beneficial to the forming, merging and shredding of the TAFFs’ vortices; as TAFFs are arranged in tandem and have the same motions, the leading edge vortex and wake vortex of the TAFFs are meaningful for improving the thrust force of their adjacent ones.     

Numerical simulations of wave–current flow in an ocean basin

Wave–current flow is a phenomenon that is present in many practical engineering situations. Over the past several decades, this type of flow has been increasingly investigated under controlled laboratory conditions. This paper presents a numerical study of wave–current flow in the ocean basin of the LabOceano (COPPE/UFRJ). A homogeneous multiphase model based on the RANS equations and the k–ɛ turbulence model implemented in ANSYS-CFX code were used. A cross section of the ocean basin was represented. A regular wave with a height of 0.08 m and a period of 1.80 s (i.e., a wave steepness of H/L = 0.016), propagating on favourable currents, was simulated. The behaviour of the free surface elevation over time and the streamlines along the basin for wave and wave–current flows were presented. The numerical results were compared to the non-viscous theory given by the Rayleigh equation applied to the problem of wave–current interaction. Good agreement was found between the wave length estimated by the numerical results and the analytical solutions, with a deviation of less than 2%.     

Simplified CFD modeling for bilge keel force and hull pressure distribution on a rotating cylinder

A horizontal, circular cylinder fitted with one bilge keel is forced to rotate harmonically around its axis. The bilge keel load and hull pressure distribution are investigated. A fully submerged condition (infinite fluid), and three partly-submerged conditions are considered. A two-dimensional numerical study is performed, and the results are validated against recently published experimental data by van’t Veer et al. [30]. In addition, comparisons for mass and drag coefficients are also made with experimental data for plate in infinite fluid (Keulegan and Carpenter [8]), and wall-mounted plate (Sarpkaya and O’Keefe [9]) in oscillatory flow.A Navier–Stokes solver based on the Finite Volume Method is adopted for solving laminar flow of incompressible water. The free-surface condition is linearized by neglecting the nonlinear free-surface terms and the influence of viscous stresses in the free surface zone, while the body-boundary condition is exact. This simplified modeling of the problem required the mesh to be fine only around the bilge keels, leading to a total number of cells around N ≃ 1 ×10⁴, which reduced computational cost significantly.The influence of draft and amplitude of oscillations on the bilge keel force and hull pressure distribution are considered. The bilge keel force is presented in terms of non-dimensional drag and mass coefficients including higher harmonic components. The numerical results are also compared with the industry standard empirical method for calculation of roll damping proposed by Ikeda et al. [4]. In general, a good agreement between the results of the present numerical method and the experimental data is obtained and the differences with those predicted by the empirical method are addressed.     

基于SRTM资料的小海岛CFD计算模型构建——以东澳岛为例

提出了一种利用SRTM资料构建海岛CFD计算模型的技术方法,并以珠江口的东澳岛为对象,进行了模型构建试验及边界层风场的数值模拟试验.实验结果表明,SRTM资料作为开源的资料,可有效地解析空间尺度在1 km以内数量级的海岛地形,并可以此为基础构建用于CFD模拟的计算模型,真实地刻画出岛屿的地形.利用计算模型进行的模拟试验表明,岛屿地形对风场的影响明显,且这种影响可以被计算模型有效地描述.所提出的技术未来在海岛风资源评估、风电场选址、污染扩散等领域有望发挥作用.     

CFD, system-based and EFD study of ship dynamic instability events: Surf-riding, periodic motion, and broaching

CFD and system-based simulation are used to predict broaching, surf-riding, and periodic motion for the ONR Tumblehome model, including captive and free model test validation studies. CFD shows close agreement with EFD for calm water resistance, static heel (except for sway force and yaw moment), and static drift (except for roll moment). CFD predictions of static heel in following waves also compare well with EFD except for surge force, sway force, and pitch angle. Froude-Krylov calculations of wave-induced surge force in following waves provides good agreement for high Froude number, but significantly overestimates for Froude number less than 0.2. On the other hand, CFD successfully reproduces the reduction of the wave-induced surge force near Froude number 0.2, probably because CFD can capture the 3D wave pattern. CFD free model simulations are performed for several speeds and headings and validated for the first time for surf-riding, broaching, and periodic motions. System-based simulations are carried out based on inputs from EFD, CFD, and Froude-Krylov for a dense grid of speeds and headings to predict the instability map, which were found to produce fairly similar results.     

Sail pressures from full-scale, wind-tunnel and numerical investigations

The main results of a two-year project aimed at comparing full-scale tests, wind tunnel tests, and numerical analysis predictions are presented. Pressure measurements were obtained from both full-scale tests and wind tunnel tests, in upwind and downwind conditions. The upwind wind tunnel test condition was modelled using a Vortex Lattice code, while the downwind wind tunnel test was modelled using a Navier-Stokes code. The pressures obtained from the three different methods are compared on three horizontal sections of the headsail, mainsail and asymmetric spinnaker. In general the pressure from the three experiments showed good agreement. In particular, very good agreement was obtained between the numerical computations and the wind tunnel test results. Conversely, the results from the downwind full-scale pressure measurements showed less similarity due to a slightly tightened trim being used for the spinnaker in the on-water tests. Full-scale tests allow the action of unsteadiness due to the wind, wave and yacht movements to affect the results. This unstable environment caused the asymmetric spinnaker to move around, and a tightened trim was required to prevent the spinnaker from collapsing.