香山（台湾）养殖牡蛎重金属含量和生长环境的关系

1991年8月～lO月和1992年3月．分别在台湾西部沿海的香山养殖区采集牡蛎以及附近河川溶解态、悬浮态底泥样品进行金属元素的分析，发现牡蛎和溶解态、悬浮态中的铜锌比值一致，显示牡蛎内重金属的累积量和生长环境中金属含量有关，     

风浪周期分布与谱宽度的关系

本文通过分析实验室风浪周期分布,发现风浪周期累积概率分布曲线低于Longuet-Higgins理论结果,在小概率周期区域实验结果与理论结果的差异明显。对实验结果进一步分析发现,在谱不是很窄时,在小概率处风浪周期累积概率随谱宽度的增大而降低,这与窄谱假定下的理论结果相反,Longuet-Higgins理论结果在小概率处不便于描述周期分布随谱宽度的变化。根据实验结果提出风浪周期的Weibull分布经验公式,Weibull分布中的参数依赖于谱宽度。     

伊利诺斯盆地宾夕法尼亚纪沉积物季节性降雨的证据

伊利诺斯盆地宾夕法尼亚纪沉积物季节性降雨的证据ＥｒｉｋＰ．Ｋｖａｌｅ等根据古纬度位置、动物群证据或气候敏感岩性的出现而恢复的古气候可表达一个地区相当长时期的气候格局，但气候的细节只有通过与目前条件相同地区的比较才能推断。由于时间的迁移、海洋和陆地的变...     

西藏崩错8级地震地表破裂的变形特征及其破裂机制

1951年11月18日,西藏那曲崩错附近发生了一次8级地震,地表产生了长达约91公里的破裂带。本文总结了该破裂的几何、位移分布特征,讨论了破裂的形成机制和崩错地震的发震构造条件     

智能全站仪在大型压力容器焊接变形监测中的应用

在大型压力容器的部件焊接过程中,由于预热、焊接等工艺流程会导致各部件产生变形,从而引起部件之间的位置关系产生变化。为保证压力容器成品满足设计要求,必须在制造过程中实施变形监测,依据变形数据适当调整焊接工艺流程,控制变形量。提出采用智能全站仪配以自动变形监测软件对大型压力容器焊接变形进行实时监测,并应用于生产实践中,监测结果表明该方法自动化程度高、实时性好,能同时给出位置和姿态变形数据。     

北京市地铁暗挖施工沉降控制探讨

仅以北京市地铁4#线张自忠车站主体暗挖施工的沉降监控项目为研究背景,对穿越城市主干道的车站结构暗挖施工进行连续性的沉降变形监测;从地下构筑物暗挖施工的工序变化与地表沉降的关系进行试验研究.在预测基础上对获取的数据进行多层次的统计与分析,以研究其变形规律与稳定性,实现了信息化施工.     

变形监测信息管理系统的设计与实现

介绍了GIS数据管理与图形显示的优势、组件技术,设计了变形监测数据管理系统平台,实现了变形监测数据的智能化管理、分析与预测.     

徕卡GPS静态测量在小浪底变形监测中的应用

一、小浪底水利枢纽工程大坝变形观测设计方案1.工程概况小浪底水利枢纽工程位于黄河干流最后一个峡谷出口,上游距三门峡水利枢纽130 km,下游距郑州花园口128 km,是惟一能在黄河下游取得较大库容的控制性工程。枢纽建成后,能有效地控制黄河泥沙,减少下游淤积,提高下游的防洪标准。小浪底水利枢纽大坝为壤土斜心墙堆石坝,最大坝高154 m,坝顶长1 667 m,坝顶宽12 m,最大底宽800 m。2.主坝外部变形观测设计方案为了监测主坝的外部变形情况,在坝顶及上下游坝坡上共布设了15条视准线,工作基点24个(其中基岩标7个),表面位移标点145个,见图1。原设计…     

Jurassic Tectonics of North China: A Synthetic View

This paper gives a synthetic view on the Jurassic tectonics of North China, with an attempt to propose a framework for the stepwise tectonic evolution history. Jurassic sedimentation, deformation and magmatism in North China have been divided into three stages. The earliest Jurassic is marked by a period of magmatism quiescence （in 205-190 Ma） and regional uplift, which are considered to be the continuation of the “Indosinian movement” characterized by continent-continent collision between the North and South China blocks. The Early to Middle Jurassic （in 190-170 Ma） was predominated by weak lithospheric extension expressed by mantle-derived plutonism and volcanism along the Yanshan belt and alongside the Tan-Lu fault zone, normal faulting and graben formation along the Yinshan- Yanshan tectonic belt, depression and resuming of coal-bearing sedimentation in vast regions of the North China block （NCB）. The Middle to Late Jurassic stage started at 165y.5 Ma and ended up before 136 Ma; it was dominated by intensive intraplate deformation resulting from multi-directional compressions. Two major deformation events have been identified. One is marked by stratigraphic unconformity beneath the thick Upper Jurassic molasic series in the foreland zones of the western Ordos thrust-fold belt and along the Yinshan-Yanshan belt; it was predated 160 Ma. The other one is indicated by stratigraphic unconformity at the base of the Lower Cretaceous and predated 135 Ma. During this last stage, two latitudinal tectonic belts, the Yinshan-Yanshan belt in the north and the Qinling-Dabie belt in the south, and the western margin of the Ordos basin were all activated by thrusting; the NCB itself was deformed by the NE to NNE-trending structural system involving thrusting, associated folding and sinistral strike-slip faulting, which were spatially partitioned. Foliated S-type granitic plutons aged 160-150 Ma were massively emplaced in the Jiao-Liao massif east of the Tan-Lu fault zone and indicate important crustal thicken