Optimization of grid-drilling using computer simulation

A computer simulation method has been developed to find efficient drilling grids for mineral deposits. A well-known ore deposit is used as a model to develop an efficient pattern for undiscovered ore bodies in the same area or in other prospects where similar geometry is suspected. The model for this study is the Austinville, Virginia deposit, a Mississippi Valley-type deposit composed of 17 ore bodies totaling 34 million short tons (30 million metric tons). The method employs a computer program that simulates drilling the model deposit with different patterns, including various levels of follow-up drilling. Follow-up holes are drilled in fences at one half the original spacing around holes in the grid that show ore-grade mineralization. Each pattern is drilled 100 times from random starting locations to provide a range of outcomes of drilling, including the best, worst, and most likely. For this study, patterns of 100 drill holes were composed of 10 fences spaced 1000–5000 feet (305–1524 m) apart, each with 10 holes spaced 200–1000 feet (61–305 m) apart. In all, 25 grids were used with zero to three levels of follow-up drilling. The 600/2000 grid, with drill holes spaced 600 feet (183 m) apart in fences spaced 2000 feet (610 m) apart, was compared with the 200/5000 grid because they represented contrasting outcomes. The 600/2000 grid penetrated many ore bodies consistently but with few multiple hits to individual ore bodies; whereas the 200/5000 grid inconsistently penetrated few ore bodies with many multiple hits. The 600/2000 grid was more efficient than the 200/5000 grid at hitting large ore bodies of 1,000,000 short tons or greater (900,000 metric tons or greater) and was made more effective by adding one cycle of follow-up drilling. The 600/2000 grid had a 97% chance of hitting one or more large ore bodies with at least one drill hole per ore body, and the 200/5000 grid had a 64% chance. Once hit, there was an 82% chance that the largest ore body would be penetrated by three or more holes when using the 600/2000 grid and an 88% chance using the 200/5000 grid.     

胜利二号极浅海步行坐底式钻井平台防腐措施研究

本文根据胜利二号极浅海步行坐底钻井平台的作业和工作环境特点，进行了防腐措施研究，设计了切合实际的防腐措施。该平台在海上作业近四年进坞修理，经观测防腐情况良好。     

洞穴完井工艺在寿阳地区煤层气钻井中的应用

洞穴完井工艺包括钻井、完井、排水采气等工序,为提高煤层渗透率,最大限度的保证煤层气解析与运移,洞穴完井一般要求有效井径3-4m,及一定范围的破碎带。远东能源公司为开采寿阳地区15#煤层中的煤层气,部署了4口生产井．其井身设计为三开结构。钻井主要设备为T685WS顶驱车载钻机及多台不同型号的空压机,采用潜孔锤冲击钻进．以空气、空气泡沫为冲洗介质,钻进至15#目标煤层底板以下46m处完钻,然后利用可伸缩式扩孔器进行扩孔。在扩孔至距三开井底8～10m时．开始采用空气和清水憋压,通过瞬间释放压力,使煤层坍塌,如此反复,至造穴直径达到要求。由于严格按照技术标准及操作流程作业,采取的技术措施合理,4口井均已顺利投入生产,增产效果显著。可见该种洞穴完井技术的应用,不仅可以保护煤层原生结构及环境,并且还能减少煤层气射孔、压裂等环节的费用．对于煤层气井施工具有重要的经济意义。     

随钻测录井地质导向二维分解实时绘图方法

根据随钻测录井实时地质导向和大斜度、水平井评价成图技术需求，针对传统绘图方法存在的弊端，提出了将测录井信息、井眼轨迹和地质模型进行二维分解的实时绘图方法。针对二维分解绘图方法绘图时空复杂度较高的问题，给出了不同事件驱动下的局部实时计算和拷屏重绘算法，控制了对CPU和内存的消耗、提高了绘图效率，消除了实时绘图的闪烁和卡顿现象。应用实例表明，二维分解实时绘图方法能够实现大尺度随钻测录井地质导向图形的流畅、无卡顿实时绘图，可提高大斜度、水平井储层模型评价的刻画精度和时效。     

Physical properties of ultrahigh-pressure metamorphic rocks from the Sulu terrain, eastern central China: implications for the seismic structure at the Donghai (CCSD) drilling site

About 30 samples representing major lithologies of Sulu ultrahigh-pressure (UHP) metamorphic rocks were collected from surface exposures and exploration wells, and compressional (Vp) and shear wave (Vs) velocities and their directional dependence (anisotropy) were determined over a range of constant confining pressures up to 600 MPa and temperatures ranging from 20 to 600 °C. Samples range in composition from acidic to ultramafic. P- and S-wave velocities measured at 600 MPa vary from 5.08 to 8.64 km/s and 2.34 to 4.93 km/s, respectively. Densities are in the range from 2.60 to 3.68 g/cm³. To make a direct tie between seismic measurements (refraction and reflection) and subsurface lithologies, the experimental velocity data (corresponding to shallow depths) were used to calculate velocity profiles for the different lithologies and profiles of reflection coefficients at possible lithologic interfaces across the projected 5000-m Chinese Continental Scientific Drilling Program (CCSD) crustal segment. Comparison of calculated in situ velocities with respective intrinsic velocities suggests that the in situ velocities at shallow depths are lowered by an increased abundance of open microcracks. The strongly reflective zone beneath the Donghai drill site can be explained by the impedance contrasts between the different lithologies. Contacts between eclogite/peridotite and felsic rocks (gt-gneiss, granitic gneiss), in particular, may give rise to strong seismic reflections. In addition, shear-induced (lattice preferred orientation (LPO)-related) seismic anisotropy can increase reflectivity. For the explanation of the high velocity bodies (>6.4 km/s) around 1000 m and below 3200-m depth, large proportions of eclogite/peridotite (about 40 and 30 vol.%, respectively) are needed.     

非开挖导向钻进实际轨迹的控制设计

非开挖导向钻进技术，具有施工速度快、适用范围广等优点，得到了广泛的应用。在实际钻进中，由于钻进在地下的不确定性，影响了导向钻进的顺利进行。到得钻进中当前点的顶角、方位角和孔深，通过均角全距法原理，可以近似地描绘出当前钻孔的空间实际轨迹，并确定钻头的位置。应用这一原理，同时运用VisualBasic语言和AutoCAD绘图工具相结合的方法，编制一套应用程序，可以直接绘制出当前钻孔轨迹，并可实现对钻孔轨迹的调控，从而保证导向钻进的顺利进行。     

路用探地雷达的应用技术研究进展

有效、无损、快捷、简便是公路检测技术发展的方向，当前国内外先进的浅层勘探技术——路用探地雷达检测，以其无损、快捷以及浅层高分辨率的优势被迅速应用于公路检测。本文对近年来路用探地雷达技术的发展及应用情况进行了介绍，详细分析了探地雷达的工作原理、系统组成结构。就探地雷达在公路建设、维护过程中的应用情况进行了系统总结。     

Utilization of lime,slag and fly ash for improvement of a colluvial soil in New South Wales,Australia

In Australia, colluvial soils form large terrains which are often subjected to considerable erosion and mass movement. This study presents a laboratory evaluation of the improvement effected by hydrated lime, milled blast furnace slag and fly ash on a fine grained (erosive) colluvial soil in New South Wales, Australia. Geotechnical tests were conducted to determine the compaction and consolidation characteristics and the compressive and shear strength properties of the blended and natural soil specimens. The effect of these additives on the Atterberg limits and pH levels is also investigated. As large amounts of fly ash and steel slag are produced in New South Wales, it is economically attractive to utilize these industrial by-products for ground improvement rather than employing conventional methods such as lime treatment. This study demonstrates that for the colluvial soil tested, milled slag is the most effective in terms of improving the internal friction angle of the treated soil, while lime is the most suitable for achieving the optimum compressive strength. Non-pozzolanic fly ash is found to be inappropriate as a soil improving agent. The cost of ground treatment using the various additives is also estimated and compared.     

硬质合金复合片齿钎具

运用力学原理研制成功了复合片齿钎头和复合片齿整钎，并批量投入市场。该系列钎具凿岩速度、寿命和硬质合金片齿有效利用率均显著优于片状和球齿钎具。