苏州城市规划区Ⅱ承压水开采与地面沉降预防控制研究

在孔隙承压水开采与地面沉降的关系上存在2种观点。水、土应力平衡理论认为：只要开采承压水，就会引发应力失衡并导致地面沉降；而水、土动态平衡理论则认为：除非开采水压力至水、土应力平衡面以下，否则不会引发地面沉降。苏州城市规划区第Ⅱ承压水开采水位与地面沉降动态观测表明，在-33m处存在一个天然动态水、土应力平衡面。第Ⅱ承压含水层形成后，经上覆堆积物自重压力长期压缩作用，其水压力具较高的压强．这种天然状态下产生的弹性释放储存量可开采利用多少，取决于开采状态下水、土应力平衡时可消耗压力水柱高度中的水头值。因而地面沉降的根本原因是开采水位超过了-33m，突破了天然状态水、土应力平衡面水位。Ⅱ承压含水层在天然状态受上覆堆积物重力产生的高压强弹性释放储存量现象，可以帮助我们确立该地区孔隙Ⅱ承压水开采不产生地面沉降的临界水位(水、土应力平衡面)。这一点对承压水开采条件、可开采资源性质具有重大实际意义。同样可以应用于饱受地面沉降困扰的无锡、常州及周边地区，为地下水开发利用政策由单一的封井停采转为目标水位控制开采提供了科学依据。同时也为此政策在承压水动力学机制上找到了内在原因。     

基于梯度塑性理论的岩样在压剪条件下变形及稳定性分析

考虑了正应力及剪应力联合作用在岩样的端部,而且,在正应力被视为变量,剪应力被视为常量这一特殊条件下,对剪切带的变形特征及剪切带-带外弹性体系统的失稳判据进行了分析.根据剪切虎克定律及梯度塑性理论,提出了剪切带内部弹性应变、塑性应变及总应变的解析式,对上述三种应变进行积分,提出了剪切带错动弹性位移、塑性位移及总位移的解析式.利用压缩虎克定律及几何关系建立了剪切带外弹性体的刚度的表达式.根据刚度理论,建立了剪切带-带外弹性体系统的失稳判据.考虑岩样端面的剪切应力后,在流动剪切应力相同时,剪切带内部的弹性剪切应变(均匀分布)将增加;剪切带内部的塑性剪切应变(不均匀分布)将减小;剪切带的弹性剪切位移(线性分布)将增加;剪切带的塑性剪切位移(非线性分布)将减小;剪切带错动位移要小一些.另外,剪切应力对剪切带-带外弹性体系统的失稳判据没有影响.失稳判据仅和岩石的本构参数、剪切带倾角及结构尺寸有关.     

双剪统一强度准则改进及其在岩土工程中的应用

在分析Mohr-Coulomb强度准则和双剪统一强度准则的基础上,提出了主剪面应力对和主剪面应力对的作用这2个新概念,并以此为出发点,通过考虑十二面体单元主剪面上所有3个主剪面应力对的共同作用,在双剪强度准则的基础上提出了一个新准则,并对其作了极限线分析.应用该新强度准则研究了静水压力条件下圆形巷道围岩弹塑性分析和土压力计算问题.研究表明,该准则不仅能较好地非线性反映岩土的3个基本强度特征,还解决了双剪统一准则中存在的双重破坏角问题.     

考虑应力水平的软土固结系数计算与试验研究

在固结度计算中通常将固结系数视为常数,实际上并非如此.通过研究软土固结系数在压缩过程中随应力水平变化的规律,推导出正常固结和超固结状态下固结系数与有效应力之间的表达式.在正常固结状态下,当应力水平小于在前期固结压力时,固结系数随应力水平的增加而增加;当超过前期固结压力后,固结系数随应力水平的增加而减小;在超固结状态下,固结系数随应力水平的增加而增加,在一定程度后趋于平稳.室内试验结果进一步说明了和验证固结系数这一特点.推导的固结系数与固结应力水平关系表达式是可行的,其计算值与试验结果的变化趋势一致,大小基本吻合,将其用于计算变形速率和固结度中,可提高准确性.     

Geological controls on rock mass classification of coal from Huntly East Mine, New Zealand

Rock Mass Rating (RMR) measurements from 65 sites within Huntly East underground coal mine are presented. All measurements are in coal, for which the dominant discontinuities are vertical cleat. Basic RMR values using two discontinuity spacings are presented: overall RMR based on the average spacing of all individual discontinuities; and cleat zone RMR based on the average spacing between zones of cleat. Cleat orientations are highly variable, but on average approximately parallel horizontal stress axes (face cleat follows maximum horizontal stress axis, butt cleat follows minimum horizontal stress axis).Contours of RMR variations throughout the mine are used to compare rock mass conditions with geological structure. It is apparent that: (1) RMR is least within downthrown fault blocks, and particularly immediately on the downthrown sides of faults, and greatest in upthrown fault blocks; and (2) RMR contours parallel horizontal stress axes within fault-bounded blocks, and bend to parallel faults at block boundaries. From similar contours for parameters contributing to RMR, the Rock Quality Designation (RQD), groundwater rating, and discontinuity condition rating create most of the observed variations in RMR. RQD is determined from the measured discontinuity frequency and hence is a measure of the degree of fracturing of the rock mass. This is interpreted as influencing the groundwater and condition parameters directly by allowing greater water ingress. Discontinuity frequency is greatest (least spacing) in the immediate vicinity of faults, and in downthrown fault blocks, generating low RMR values. Within fault blocks RQD varies little, so RMR contours align with cleat orientations.As RMR contours, faults, stress field and cleat orientation are clearly interrelated, there is unequivocally a connection between RMR and structural geology; this allows some predictive capacity in terms of ground conditions. If geological features can be accurately defined through either drilling programs or seismic surveys, then ground conditions may be predicted before panels are driven.     

Triaxial stress state deep in orogenic belts: an example from Turkey

A rare metachert pebble containing amphibole grains with microboudin structures in a wide range of orientations provides an opportunity to perform stress analysis in two orthogonal orientations on the foliation surface. The sample was analysed by the microboudin method to infer the triaxial stress state during microboudinage. Stress parameters proportional to the far-field differential stress were determined for sodic amphibole grains in the two orientations. The ratio of the stresses in the two orthogonal orientations (σ₁−σ₂)/(σ₁−σ₃) was calculated to be 0.64, indicating that σ₂ lies closer to the midpoint between σ₁ and σ₃ than to σ₃.     

Focal mechanism dependence of static stress triggering of earthquakes

We perform a global statistical investigation into the problem of Coulomb stress triggering of earthquakes by using the Harvard CMT catalogue of shallow earthquakes from 1976 to 2001. We consider ‘earthquake pairs’, i.e., pairs of successive earthquakes occurring near each other with similar focal mechanisms, and address the problem of whether or not the change of the Coulomb failure stress (CFS) produced by the first earthquake of the pair ‘encourages’ the occurrence of the second one. An interesting feature is that such a Coulomb stress-triggering phenomenon has an apparent focal mechanism dependence: for thrust earthquakes, a more evident triggering effect can be observed.