夯扩桩沉管控制贯入度计算法

通过改造格尔谢万诺夫打桩公式,提供了夯扩桩沉管控制贯入度计算表达式,在此 ,介绍了沉积控制贯入度在夯扩桩设计和施工中的用途,并举例验证。     

SEISMIC IMPACT LOADING IN INELASTIC TENSION-ONLY CONCENTRICALLY BRACED STEEL FRAMES: MYTH OR REALITY?

Tension-Only Concentrically Braced Frames (TOCBF) exhibit deteriorating pinched hysteretic behaviour during strong earthquakes. Slender braces transit between an elastic buckling state, a restraightening state, in which they carry almost no load, an elastic tensile loading state as they are suddenly taut and, finally, a tensile yielding state. It has long been suspected that the sudden increase in tensile forces in the braces of TOCBSF creates detrimental impact loading on the connections and other structural elements. No experimental evidence, however, has been provided so far to confirm, or to quantify, this impact phenomenon. This paper addresses this issue through shake table tests of half scale, two-storey, TOCBF models. By normalizing the hysteresis loops of braces obtained from shake table tests to the yield strength of steel obtained from quasi-static tests, the increase in tensile forces in the braces was obtained. Results of dynamic tensile tests on steel coupons under similar strain rates as observed during the shake table tests showed that this increase in tensile forces is not the result of impact, but is rather caused by a yield strength increase of the steel under high strain rate. A procedure is proposed to estimate and account for this increase in tensile forces in the braces at the design stage.     

福建省泉州晋江大桥桥位方案通航技术分析

福建省泉州晋江大桥位于晋江顺济桥至户坑口河段,桥梁横跨晋江两岸,拟选桥位方案为合成氨厂桥位和前埔桥位,本文通过对两个拟选桥位进行桥区河床演变、水流条件分析和通航要求论证。对拟选晋江大桥两个桥位方案进行必选,推荐合理的桥位方案,为大桥桥位的选择提供了科学的依据,对同类桥梁选址具有一定的参考价值     

工作状态下梁及桥梁模态与损伤识别的新方法

工作状态下桥梁结构的模态参数识别是桥梁损伤识别的重要环节,考虑桥梁检测的实用性,桥梁检测一般应建立在环境激励的基础上,已有的环境激励下模态参数识别的方法对模态频率的识别的精度较高,而对位移模态的识别则误差较大。提出了一种利用移动质量块在不同位置时对桥梁的模态频率进行多次测量,用各次测得的频率值确定位移模态的新方法,使得位移模态识别的精度接近频率识别的精度,建立了该方法的初步模型,推导了频率与位移模态关系的理论公式,并通过数值模拟对该方法的有效性进行了说明。     

多高层钢结构耐火性能的子结构分析模型与分析方法

基于整体钢结构在局部火灾下的反应规律,将高层钢结构的初始倒塌破坏类型进行了分类(中间柱初始倒塌、边柱初始倒塌以及梁柱同时倒塌),根据整体结构约束影响和荷载影响,提出局部火灾下多高层钢结构耐火性能分析的相应子结构分析模型及其分析方法。子结构模型的边界充分考虑周围约束的影响,尤其是周围梁和上层柱构件以及层数的影响。针对不同类型的子结构模型,通过建立相应的具体子结构有限元模型,合理考虑边界条件的影响。最后基于建立的数值模型,研究了子结构的火灾反应规律与破坏机理,并与整体结构的分析结果进行了比较,结果表明:子结构分析模型与分析方法可以合理准确地分析整体结构的耐火性能。     

Seismic fracture evaluation of diaphragm joints in welded beam-to-box column moment connections

Steel box columns are widely used in steel building structures in Taiwan due to their dual strong axes. To transfer the beam-end moment to the column, diaphragm plates of the same thickness and elevations as the beam flanges are usually welded inside the box column. The electro-slag welding (ESW) process is widely used to connect the diaphragms to the column flanges in Taiwan because of its convenience and efficiency. However, ESW may increase the hardness of the welds and heat-affected zones (HAZs), while reducing the Charpy-V notch strength in the HAZ. This situation can cause premature fracture of the diaphragm-to-column flange welds before a large plastic rotation is developed in the beam-to-box column joints. To quantify the critical eccentricity and the effectiveness of fracture prediction, this study uses fracture prediction models and finite element model (FEM) analysis to correlate the test results. In this study, two beam-to-box column connection subassembly tests are conducted with different loading protocols and ESW chamber shapes. To implement a fracture prediction model, the material parameters are established from circumferential notched tensile tests and FEM analysis. Test results indicate that the fracture instances can be predicted on the basis of the cumulative plastic deformation in the HAZs. Analytical results indicate that fracture instances and locations are sensitive to the relative locations of the ESW joints and beam flange. Tests also confirm that the possible fracture of the diaphragm-to-column flange joints can be mitigated by enlarging the chamber of the ESW joint.     

铰接隅撑钢框架抗震性能研究

传统抗弯钢框架的梁柱节点通常设计为刚性连接,这种刚性节点具有很大的抗弯刚度,然而节点延性不足,罕遇地震作用导致节点脆性断裂.研究学者提出了多种解决该问题的思路,例如半刚性连接节点、节点加强或削弱方法使塑性铰外移等.本文提出了一种简化的梁柱节点连接方式-铰接连接,改变梁柱节点的传力方式,在节点处设置隅撑提供框架的抗侧刚度...     

高强度Q460钢材高温力学性能试验研究

采用恒温拉伸法和振动法分别对国产高强度Q460钢材在高温下的强度和弹性模量进行了试验研究。根据试验结果对屈服强度、极限强度和弹性模量进行了拟合,得到了Q460钢材的力学性能指标随温度变化的函数表达式。将Q460钢的高温力学性能指标和普通结构钢进行了对比。研究结果表明:高强度Q460钢材的强度和弹性模量随温度的升高而降低;Q460钢材高温下的强度折减系数比普通钢低,同等条件下,Q460钢结构比普通钢结构具有较好的抗火性能。     

特大型桥梁施工GPS高程控制网技术研究

探索了采用GPS技术建立桥梁施工高程控制网的难点及关键问题,分析了GPS跨河高程传递测量方法的技术要点,结合工程实例得出了一些结论和建议。     

大气折光系数测定及在悬索桥基准索股线形测量中的应用

大跨度悬索桥基准索股跨中位置处于百米高空,如何测得精确的垂度值,对主缆线形进行控制至关重要。本文分析了影响悬索桥基准索股垂度测量精度的主要因素,提出了基于实时大气折光系数改正的单向三角高程的跨中垂度测量新方法。在桥址区建立高精度的高差基准,通过对桥址区的大气折光系数的测定及改正试验,证明该测量方法切实可行。基准索股跨中垂度采用双测站进行测量,当双测站所测同一点绝对垂度互差小于10 mm时,取双测站所测垂度均值作为该点的垂度值。该方法的测量结果达到设计精度要求,对同类工程测量项目有借鉴意义。