中高层钢筋混凝土异形柱框架结构弹塑性时程分析

用杆模型编制了钢筋混凝土异形柱框架结构的弹塑性时程分析程序FEANT。采用该程序对一中高层大开间钢筋混凝土异形柱框架结构振动台试验模型进行了计算分析，计算值与试验值吻合较好，能满足工程需要。     

航放异常解释用Z量板的水泥模型验证

对航放异常矩形反演使用的理论Z量板进行了水泥板模型验证，解决了在航放实测条件下难以验证以及如何消除验证模型对γ射线的等效空气吸收系数与空气本身对γ射线的吸收系数不同的影响等问题。验证结果表明，该量板是正确的，可用的。     

珠江三角洲软土微结构的定量研究

对用不同长度的PVC管在珠海和广州两地采得的淤泥样柱施于一定荷载，然后在扫描电镜下研究软土受压后在样柱垂深方向上的微结构变化，并将样品的微结构照片扫描，在计算机内进行量化处理。结果表明，样品的孔隙分布分维差随着离施压点距离的增加而逐渐减小，从而得到两者的关系方程。据此，可了解在一定荷载下应力在软土层中向下的衰减趋势。文章还对软土的天然含水量和围压对压缩变形的影响作了初步的讨论。     

Evaluation of density in layer compaction using SASW method

SASW test, which is non-intrusive and rapid in the field application, was used to evaluate the layer density in the roller compaction without performing the complicated inversion process. The concept of normalized shear wave velocity was introduced to minimize the effect of confinement in the density evaluation. SASW test was performed to determine the shear wave velocity of the layer, and the free–free resonant column (FF–RC) test was adopted to determine the correlation between the normalized shear wave velocity and density of the site, which is almost unique independent of confinement. Testing and data reduction procedures of both tests were briefly discussed and an evaluation procedure of the field density was proposed by effectively combining in-situ shear wave velocity determined by the SASW test with the correlation between the normalized shear wave velocity and the density determined by the FF–RC test. Finally, the feasibility of the proposed method was verified by performing a field case study at Hoengsung road construction site. Field densities determined by the proposed method matched well with those determined by sand cone tests, showing the potential of applying the proposed method in the field density evaluation.     

岩矿中稀土元素离子交换分离富集的改进及ICP—AES测定

本文通过对离子交换柱的规格改进,提高了分离效率,加快了分离速度(流速v/(ml·min~(-1)))可达1.0—1.5.结合分离富集条件的选择及ICP-AES测定方法的联用,使本法不分析周期短、所耗试剂省,且检测限低、精密度和准确度较高.经标样检验和矿样实测对比,其结果均令人满意.     

A case of no-wind plinian fallout at Pululagua caldera (Ecuador): implications for models of clast dispersal

The caldera of Pululagua is an eruptive centre of the Northern Volcanic Zone of the South American volcanic arc, located about 15 km north of Quito, Ecuador. Activity leading to formation of the caldera occurred about 2450 b.p. as a series of volcanic episodes during which an estimated 5–6 km³ (DRE) of hornblende-bearing dacitic magma was erupted. A basal pumice-fall deposit covers more than 2.2x10⁴ km² with a volume of about 1.1 km³ and represents the principal and best-preserved plinian layer. Circular patterns of isopachs and pumice, lithic and Md isopleths of the Basal Fallout (BF) around the caldera indicate emplacement in wind-free conditions. Absence of wind is confirmed by an ubiquitous, normally graded, thin ash bed at the top of the lapilli layer which originated from slow settling of fines after cessation of the plinian column (co-plinian ash). The unusual atmospheric conditions during deposition make the BF deposit particularly suitable for the application and evaluation of pyroclast dispersal models. Application of the Carey and Sparks' (1986) model shows that whereas the 3.2-, 1.6-, and 0.8-cm lithic isopleths predict a model column height of about 36 km, the 6.4-cm isopleth yields and estimate of only 21 km. The 4.9- and 6.4-cm isopleths yield a column height of 28 km using the model of Wilson and Walker (1987). The two models give the same mass discharge rate of 2x10⁸ kg s^-1. A simple exponential decrease of thickness with distance, as proposed by Pyle (1989) for plinian falls, fits well with the BF. Exponential decrease of size with distance is followed by clasts less than about 3 cm, suggesting, in agreement with Wilson and Walker (1987), that only a small proportion of large clasts reach the top of the column. Variations with distance in clast distribution patterns imply that, in order to obtain column heights by clast dispersal models, the distribution should be known from both proximal and distal zones. Knowledge of only a few isopleths, irrespective of their distance from the vent, is not sufficient as seemed justified by the method of Pyle (1989).     

Development and validation of a metallic haunch seismic retrofit solution for existing under‐designed RC frame buildings

The feasibility and efficiency of a seismic retrofit solution for existing reinforced concrete frame systems, designed before the introduction of modern seismic‐oriented design codes in the mid 1970s, is conceptually presented and experimentally investigated. A diagonal metallic haunch system is introduced at the beam–column connections to protect the joint panel zone from extensive damage and brittle shear mechanisms, while inverting the hierarchy of strength within the beam–column subassemblies and forming a plastic hinge in the beam. A complete step‐by‐step design procedure is suggested for the proposed retrofit strategy to achieve the desired reversal of strength hierarchy. Analytical formulations of the internal force flow at the beam–column‐joint level are derived for the retrofitted joints. The study is particularly focused on exterior beam–column joints, since it is recognized that they are the most vulnerable, due to their lack of a reliable joint shear transfer mechanism. Results from an experimental program carried out to validate the concept and the design procedure are also presented. The program consisted of quasi‐static cyclic tests on four exterior, ? scaled, beam–column joint subassemblies, typical of pre‐1970 construction practice using plain round bars with end‐hooks, with limited joint transverse reinforcement and detailed without capacity design considerations. The first (control specimen) emulated the as‐built connection while the three others incorporated the proposed retrofitted configurations. The experimental results demonstrated the effectiveness of the proposed solution for upgrading non‐seismically designed RC frames and also confirmed the applicability of the proposed design procedure and of the analytical derivations. Copyright © 2006 John Wiley & Sons, Ltd.     

一种改进的Delaunay三角化算法研究

Delaunay三角化在诸多应用领域具有极其广泛用途,也一直是计算机图形图像学和科学计算可视化技术的重要研究内容。针对二维约束Delaunay三角化问题,提出一种快速生成算法。该算法首先建立环形矩形,分环分治平面散乱点;然后依据Delaunay三角形的性质,从外环到内环分治逐步插入新点,一环插入完毕后,整理有效Delaunay三角形;依次循环快速生成二维约束Delaunay三角网格。本算法计算过程简单,计算效率高,程序编写十分容易无需复杂的递归过程,技巧性地解决了二维约束Delaunay三角化问题。实例证明,该算法具有较好的应用效果。     

大面积深厚杂填土地基处理技术

通过一项具体的工程实例,论述了深厚杂填土地基的基本工程特性。介绍了一种处理深厚杂填土地基的新技术———重锤冲扩挤密灰渣土桩复合地基技术,并对施工过程的控制,以及施工效果的检测结果进行了分析,得出了对于大面积深厚杂填土地基采用此技术处理后,能够消除地基深部湿陷性,复合地基承载力可以满足200 kPa。     

万丰路桥大吨位矩形截面桩成孔施工技术

针对在卵石及基岩地层中桩孔施工时成孔难、渗漏大的问题，以液压抓斗为成孔设备，采用合理的机械结构、钻进方法、泥浆配方进行矩形截面桩的施工。