Acceleration response modification factors for nonstructural components attached to inelastic moment‐resisting frame structures

A statistical analysis of the peak acceleration demands for nonstructural components (NSCs) supported on a variety of stiff and flexible inelastic regular moment‐resisting frame structures with periods from 0.3 to 3.0 s exposed to 40 far‐field ground motions is presented. Peak component acceleration (PCA) demands were quantified based on the floor response spectrum (FRS) method without considering dynamic interaction effects. This study evaluated the main factors that influence the amplification or decrease of FRS values caused by inelasticity in the primary structure in three distinct spectral regions namely long‐period, fundamental‐period, and short‐period region. The amplification or decrease of peak elastic acceleration demands depends on the location of the NSC in the supporting structure, periods of the component and building, damping ratio of the component, and level of inelasticity of the supporting structure. While FRS values at the initial modal periods of the supporting structure are reduced due to inelastic action in the primary structure, the region between the modal periods experiences an increase in PCA demands. A parameter denoted as acceleration response modification factor (R_acc) was proposed to quantify this reduction/increase in PCA demands. Copyright © 2007 John Wiley & Sons, Ltd.     

玉树隆宝2014年冬季冻土积雪对陆气通量关键参数的影响分析

利用玉树隆宝湿地的观测资料,分析了未冻结、冻结和冻结有积雪覆盖三种情况下动量通量和感热通量的日变化情况,计算了三种情况下动量总体输送系数、感热总体输送系数、动力学粗糙度和热力学粗糙度,分析了附加阻尼和粗糙度雷诺数的关系,并将三种附加阻尼的参数化方案进行了比较,结果表明:冻结状态下动量通量和感热通量的日变化幅度最大,冻结有积雪覆盖时,动量通量和感热通量的日变化幅度最小。动量总体输送系数C_D和感热总体输送系数C_H的值在冻结时最大,冻结有积雪覆盖时最小,动力学粗糙度和热力学粗糙度在冻结状况下最小,冻结有积雪覆盖时最大。未冻结、冻结和冻结有积雪覆盖状态下,三种附加阻尼kB~(-1)参数化方案中,幂函数型方案较为合适。     

Late Quaternary sea‐level change and evolution of Belfast Lough,Northern Ireland: new offshore evidence and implications for sea‐level reconstruction

The interplay of eustatic and isostatic factors causes complex relative sea‐level (RSL) histories, particularly in paraglacial settings. In this context the past record of RSL is important in understanding ice‐sheet history, earth rheology and resulting glacio‐isostatic adjustment. Field data to develop sea‐level reconstructions are often limited to shallow depths and uncertainty exists as to the veracity of modelled sea‐level curves. We use seismic stratigraphy, 39 vibrocores and 26 radiocarbon dates to investigate the deglacial history of Belfast Lough, Northern Ireland, and reconstruct past RSL. A typical sequence of till, glacimarine and Holocene sediments is preserved. Two sea‐level lowstands (both max. ?40 m) are recorded at c. 13.5 and 11.5k cal a bp . Each is followed by a rapid transgression and subsequent periods of RSL stability. The first transgression coincides temporally with a late stage of Meltwater Pulse 1a and the RSL stability occurred between c. 13.0 and c. 12.2k cal a bp (Younger Dryas). The second still/slowstand occurred between c. 10.3 and c. 11.5k cal a bp . Our data provide constraints on the direction and timing of RSL change during deglaciation. Application of the Depth of Closure concept adds an error term to sea‐level reconstructions based on seismic stratigraphic reconstructions.     

A one‐dimensional process‐based approach to study reservoir sediment dynamics during management operations

A comprehensive understanding of the dynamics of erosion and sedimentation in reservoirs under different management conditions is required to anticipate sedimentation issues and implement effective sediment management strategies. This paper describes a unique approach combining fluvial geomorphology tools and morphodynamic modeling for analyzing the sediment dynamics of an elongated hydropower reservoir subjected to management operations: the Génissiat Reservoir on the Rhône River. Functional sub‐reaches representative of the reservoir morphodynamics were delineated by adapting natural river segmentation methods to elongated reservoirs. The segmentation revealed the link between the spatial and temporal reservoir changes and the variability of longitudinal flow conditions during reservoir management operations. An innovative modeling strategy, incorporating the reservoir segmentation into two sediment transport codes, was implemented to simulate the dynamics of erosion and sedimentation at the reach scale during historic events. One code used a bedload approach, based on the Exner equation with a transport capacity formula, and the other used a suspended load approach based on the advection–dispersion equation. This strategy provided a fair quantification of the dynamics of erosion and sedimentation at the reach scale during different management operations. This study showed that the reservoir morphodynamics is controlled by bedload transport in upper reaches, graded suspended load transport of sand in middle reaches and suspended load transport of fine sediments in lower reaches. Eventually, it allowed a better understanding of the impact of dam management on sediment dynamics. Copyright © 2017 John Wiley & Sons, Ltd.     

Numerical modeling investigation on turbulent oscillatory flow over a plane rough bed composed by randomly arrayed particles

A three-dimensional numerical model is established to simulate the turbulent oscillatory boundary layer over a fixed and rough bed composed by randomly arrayed solid spheres based on the lattice Boltzmann method and the large eddy simulation model.The equivalent roughness height,the location of the theoretical bed and the time variation of the friction velocity are investigated using the log-fit method.The time series of turbulent intensity and Reynolds stress are also investigated.The equivalent roughness height of cases with Reynolds numbers of 1×10~4–6×10~4 is approximately 2.81 d(grain size).The time variation of the friction velocity in an oscillatory cycle exhibits sinusoidal-like behavior.The friction factor depends on the relative roughness in the rough turbulent regime,and the pattern of solid particles arrayed as the rough bed in the numerical simulations has no obvious effect on the friction factor.     

Effectiveness of simple approaches in mitigating residual deformations in buildings

Developments in performance‐based seismic design and assessment approaches have emphasized the importance of considering residual deformations. Recent investigations have also led to a proposed direct displacement‐based design (DDBD) approach which includes an explicit consideration of the expected residual deformations as an integral part of the design process. Having estimated the expected residual deformations in a structure, engineers are faced with the problem of reducing them to meet the targeted performance levels under pre‐defined seismic hazard levels. Previous studies have identified the post‐yield stiffness as a primary factor influencing the magnitude of residual deformations in single degree of freedom and multiple degree of freedom structures. In this paper, a series of simple approaches to increase the post‐yield stiffness of traditional framed and braced systems for the purpose of reducing residual deformations are investigated. These methods do not utilize recentring post‐tensioned technology. This contribution addresses the feasibility of altering the lateral post‐yield stiffness of structural systems by: (i) using different reinforcement materials with beneficial features in their stress–strain behaviour; (ii) re‐designing the section geometry and properties of primary seismic‐resisting elements; and (iii) introducing a secondary elastic frame to act in parallel with the primary system. The efficiency of each of these techniques is investigated through monotonic and cyclic moment‐curvature and non‐linear time‐history analyses. Of these approaches the design and introduction of an elastic secondary system was found to be most effective and consistent in reducing residual deformations. A simplified design approach for achieving the desired increase of a system's post‐yield stiffness is also presented. Copyright © 2007 John Wiley & Sons, Ltd.