矿用随钻动态方位伽马仪器的研制与应用

顺煤层瓦斯抽采钻孔是目前最直接最有效的瓦斯治理方法,自然伽马作为含煤地层识别常用的判识依据,可以根据地层放射性判断钻孔轨迹是否在目标层中。但现有的矿用伽马测井仪器只能进行滑动钻进测量,不适用于复合钻进及旋转导向钻进,无法满足伽马动态连续测量的工况。针对以上问题,在分析了煤矿井下随钻测量工况特点和伽马测井原理的基础上,通过低压直流载波双向通信技术进行孔底多扇区方位伽马数据的实时传输;采用屏蔽开窗的结构设计,实现单伽马晶体的8扇区分区测量;基于三轴MEMS加速度传感器和三轴MEMS陀螺仪不同的频率特性,采用互补滤波的动态测量方法,克服了回转钻进过程中振动和旋转对工具面向角测量的影响。通过地面性能测试和井下的工业性试验,验证了仪器在不同放射性地层分界面能正确反映出地层放射性变化规律。试验结果表明,仪器可以满足复合回转定向钻进时的地质导向测量要求,为煤矿井下顺煤层定向钻进提供了技术保障。      

泰国湾表层沉积物陆源碎屑的粒度特征及其展现的沉积动力环境

海洋碎屑沉积物的粒度特征是海底沉积动力环境的直接体现,是用来研究海洋动力环境变化的重要手段,尤其是陆架海底表层沉积物的粒度分布,对于研究沿岸和水柱底边界层现今海洋动力环境可起到重要作用。该项研究通过调查遍布泰国湾至湄公河口海底表层沉积物陆源碎屑的粒度分布特征,以期获得影响现今特定海域沉积作用的海洋动力环境过程。粒度分析的结果显示,泰国湾表层沉积物的陆源碎屑以细砂-细粉砂为主,分选总体较差,频率分布以正偏为主。其中,细砂-极细砂组分主要分布在曼谷湾和柬埔寨沿岸。湄公河岸外沉积物为细砂,且分选比泰国湾区域的沉积物要好。这些表层沉积物的粒度特征具有良好的环境变化指示作用。湄公河岸外分选较好、近于正态分布的中砂沉积物指示了波浪作用下的沉积环境。曼谷湾和柬埔寨沿岸分选较差的中砂-细砂粗粒沉积物反映了潮汐和波浪的共同作用;泰国湾东西沿岸区域分选中等、呈正偏态的极细砂-中粉砂沉积物体现了潮汐的控制作用;而泰国湾中部分选较差的沉积物则指示了表层洋流作用。研究表明,泰国湾和湄公河岸外表层沉积物陆源碎屑的粒度分布特征可用于区分不同海洋动力因素的控制作用,揭示出泰国湾的沉积动力环境主要受潮汐、波浪和洋流的共同影响,湄公河岸外的沉积动力环境主要受波浪的影响。     

基于IDA的层间隔震结构失效模式研究

层间隔震结构是由基础隔震结构发展而来的一种新型隔震结构。为研究层间隔震结构的倒塌,需先研究不同层间隔震结构的不同失效模式和失效位置,文章建立了3个不同结构参数的层间隔震结构有限元模型,选取20条与抗震规范反应谱吻合的地震动,采用增量动力分析（IDA）方法,分别对其失效模式和失效位置进行研究。研究表明:基于不同的结构参数,层间隔震的基本失效模式有三种,即隔震层水平位移超限导致结构失效、下部结构层间位移角超限导致结构失效、隔震层拉压应力超限导致结构失效;隔震层下部结构和隔震层最外边缘支座为结构的薄弱位置,应引起更多关注。此方法不仅可以研究结构的不同失效模式,还可以确定失效位置,可为下一步层间隔震结构的抗倒塌分析提供理论基础。     

Testing a proposed new chronology for the Jasmund Glacitectonic Complex (SW Baltic Sea): No indication of incipient deformation during MIS 3

Weichselian advances of the Scandinavian Ice Sheet have generated several glacitectonically deformed structures in the southwestern Baltic Sea area. One example is the 100 km² large Jasmund Glacitectonic Complex (JGC), which was formed proglacially and consists of two subparallel-orientated sets of composite ridges that represent a northern and southern structural complex. The two-part morphological structure of the JGC suggests a formation by two ice advances, one approaching from NE and one from SE direction. So far, this divided structure has been assumed to have been formed by short-time ice-front oscillations during an MIS 2 ice advance. However, based on their recently published ice dynamic model for MIS 3 and the available age data from Jasmund, lüthgens et al. (2020) propose a chronological reinterpretation of the JGC development, according to which two distinct ice advances during early and late MIS 3 formed the JGC. In order to test this novel stratigraphical model for the JGC formation, five OSL samples were taken from fluvial and lacustrine deposits at a key section near Glowe (NW Jasmund). The investigated succession is divided into pre-kinematic sediments, deposited before the glacitectonic deformation, and post-kinematic sediments, deposited after the deformation. Our results show that the youngest dated pre-tectonic sediment has a burial age between ∼40 and 34 ka, which rules out a glacitectonic deformation during an early MIS 3 ice advance (∼60–50 ka). In addition, by reviewing the existing age data set, a development of the JGC during an early and late MIS 3 advance of the SIS must be rejected. Instead, our data confirm the genesis of the JGC during MIS 2.     

Experimental study on the dynamic modulus of compacted loess under bidirectional dynamic load

The dynamic characteristics of compacted loess are of great significance to the seismic construction of the Loess Plateau area in Northwest China, where earthquakes frequently occur. To study the change in the dynamic modulus of the foundation soil under the combined action of vertical and horizontal earthquakes, a hollow cylindrical torsion shear instrument capable of vibrating in four directions was used to perform two-way coupling of compression and torsion of Xi'an compacted loess under different dry density and deviator stress ratios. The results show that increasing the dry density can improve the initial dynamic compression modulus and initial dynamic shear modulus of compacted loess. With an increase in the deviator stress ratio, the initial dynamic compression modulus increases, to a certain extent, but the initial dynamic shear modulus decreases slightly. The dynamic modulus gradually decreases with the development of dynamic strain and tends to be stable, and the dynamic modulus that reaches the same strain increases with an increasing dry density. At the initial stage of dynamic loading, the attenuation of the dynamic shear modulus with the strain development is faster than that of the dynamic compression modulus. Compared with previous research results, it is determined that the dynamic modulus of loess under bidirectional dynamic loading is lower and the attenuation rate is faster than that under single-direction dynamic loading. The deviator stress ratio has a more obvious effect on the dynamic compression modulus. The increase in the deviator stress ratio can increase the dynamic compression modulus, to a certain extent. However, the deviator stress ratio has almost no effect on the dynamic shear modulus, and can therefore be ignored.     

冻融作用下污泥固化轻质土动力特性及结构演化

冻融作用会影响污泥固化轻质土动力特性和结构特性。为研究不同冻融循环次数和冻结温度下的污泥固化轻质土动力特性及结构演化,对冻融循环作用后的污泥固化轻质土进行动三轴试验和固结试验。试验结果表明:在冻融循环作用下,污泥固化轻质土动应力-应变曲线呈弱应变硬化型。污泥固化轻质土动强度和变形随着冻融次数（n）的增加和冻结温度（T）的降低而减小。经历前4次冻融作用后,对固化土变形和动强度影响较大,经历8次冻融循环后基本趋于稳定。冻融循环对土体动力特性的影响本质上是对土体结构性的影响。固化土冻融结构势（m_dσn）的变化规律与动强度类似,随冻融次数的增加和冻结温度的降低而下降。冻融循环次数是影响污泥固化轻质土动力特性和结构性的主要因素,冻结温度为次要因素。     

真三轴单面临空下煤岩组合体冲击破坏特征试验研究

煤岩复合承载结构所处的应力边界条件不同,冲击地压在巷道中的显现特征和前兆规律亦不相同。采用高频振动采集及孔内成像三轴动静载试验系统,开展了高静载和动静载耦合作用下煤岩组合体真三轴单面临空试验,分析了煤岩组合体界面处力学特征和强度条件,探究了不同应力边界下煤岩组合体的破坏形态、动力显现特征和声发射信号的演变规律。研究结果表明:(1)受煤岩变形相互制约的影响,交界面处砂岩强度被"弱化"。当界面处煤体裂隙尖端的应力大于"弱化"后砂岩强度时,裂隙将穿过煤岩界面发育至砂岩中,砂岩呈现出屈曲层裂、劈裂成板的破坏形态。(2)高静载作用下,煤岩组合体变形破坏特征和声发射信号具有明显的前兆规律,组合体发生承载失效前煤体局部颗粒弹射动能增大、弹射颗粒块度降低,声发射信号由"高频低能"向"高频高能"转变,组合体的破坏形态以剪切-张拉复合破坏为主。(3)受冲击动载影响,顶底板砂岩夹持作用减弱,煤体裂纹尖端应力得不到有效积聚,裂纹扩展到煤岩交界面时被阻隔,组合体以煤样的张拉破坏为主,声发射信号呈现出"高频高能"的特点,但大多集中在冲击破坏之后,导致组合体动力破坏难以预测。(4)与纯静载作用相比,虽然动静载耦合作...     

考虑动态泥膜效应的盾构开挖面稳定理论研究

泥水盾构工法被广泛应用于高压富水复杂地质环境中修筑隧道,其中开挖面稳定控制是工程成败的关键,在盾构掘进时,由于刀盘不断旋转切削地层,开挖面上的泥膜处于“形成―破坏―再形成”的动态循环过程,泥膜透水性增强,这种动态泥膜作用下开挖面的稳定如何评价有待于进一步探索。对此,对泥水盾构掘进过程中的动态泥膜进行了分类,提出了考虑盾构运动和泥浆渗滤特征的动态泥膜理论。在此基础上,采用空间离散法将泥水压力引入旋转体模型,建立了考虑动态泥膜效应的开挖面稳定力学模型,提出了泥水盾构动态掘进过程中开挖面临界泥浆压力及泥浆支护效率评估方法,研究指出：当盾构在强渗透性地层中掘进时,在尽量提高泥浆成膜率的同时,应注重泥浆黏度调节,充分发挥渗透力支护作用,同时可适当提高盾构掘进速度并降低刀盘转速,有利于开挖面稳定控制。以泥浆成膜率、等效渗透系数为依据给出了泥浆支护效率设计图,研究工作对盾构掘进支护压力控制和泥浆配置有一定的借鉴意义。     

灌注桩动力特性试验与数值模拟研究

结合某风洞建设项目现场桩基动力特性试验,采用三维有限差分模拟软件FLAC^3D建立双桩模型基础进行计算机仿真,分析结果与试验数据吻合良好,验证了基于桩−土−结构共同作用开展数值模拟求解设备荷载作用下桩基础动力响应方法的合理性。进一步建立灌注桩后注浆模型,探讨采取不同桩侧阻力和桩端阻力增强系数对桩基动力特性的影响。结果表明：灌注桩后注浆对竖向振动的共振频率没有影响,对水平回转振动的共振频率、最大振幅、地基抗剪刚度系数和地基水平转向第1振型阻尼比的影响均很小;灌注桩后注浆能起到提高桩基抗压刚度、减少桩基最大振幅的效果,但相对于未注浆其效果有限。     

Numerical analyses of uplift behavior of pile foundation for transmission line structure in frozen soil regions北大核心CSCD

Pile foundation is one of the most commonly used and suitable foundations to support transmission line structure, especially in seasonally frozen soil regions and permafrost regions. Axial compression is the controlling condition in the design of foundations for such structures as bridges and buildings, while uplift and overturning will control the design of transmission line structure foundations. This paper presents an extensive overview of previous studies including experimental (e. g., laboratory model test and full-scale field load test), analytical/theoretical (e. g., limit equilibrium and limit analysis based on plasticity)and numerical(e. g., finite difference and finite element methods). The review indicates that study on the uplift behavior of pile foundation in frozen soil is relatively limited, particularly in the case of combined effect of axial uplift and lateral loading. Interaction between pile and frozen soil and mechanism of load transfer along the pile shaft and around the pile tip still remain unclear. Therefore, this paper implements finite difference analysis within FLAC3D to investigate the behavior of pile foundation in frozen silty clay and gravelly sand under axial uplift behavior and the effect of ground condition and lateral loading on the uplift behavior. Because of the axisymmetric condition of the problem studied, only half of the model is simulated. The chosen domain of the medium is discretized into a set of quadrilateral elements and the pile is discretized by the cylinder element. The interaction between the soil and pile is considered according to interface elements. Mohr-Coulomb criterion is adopted to model the soil behavior (perfectly elastic-plastic), while the pile is simply considered as a rigid body. The soil parameters such as Young’s modulus, cohesion and internal friction angle used for numerical analyses are determined by laboratory tests and estimated according to the empirical correlations with in-situ tests. The present numerical modeling is verified with the results from field loading tests on pile foundations in Qinghai-Tibet ±550 kV transmission line project. On this basis, parametric studies are carried out to uncover the behavior of pile in frozen soil. It is observed that pullout is the dominant failure mechanism of pile and the uplift load-displacement curve clearly exhibits an asymptote, consisting of initially linear elastic, nonlinear transition, and finally linear regions. These results are consistent with the observations in a few previous studies. In addition, larger uplift capacity of pile foundation in freezing period and gravelly sand is gained (about 20%). Lateral loading increases the deflection and therefore, decreases the uplift capacity of pile foundation. For the convenience of using the results obtained in practice, the values of uplift factor for pile foundation in silty clay and gravelly sand are provided. Finally, it should be noted that the method used, and the results obtained in the current work could be useful for engineers and designers, at least providing them some qualitative evidence for pile design in seasonally frozen soil regions and permafrost regions. This is important and necessary to ensure the safety of construction in such regions. Meanwhile, numerical analyses in the current work can be a benchmark example for subsequent research studies. © 2022 Science Press (China).