Numerical modeling for analyzing thermal surface anomalies induced by underground coal fires

Coal seams burning underneath the surface are recognized all over the world and have drawn increasing public attention in the past years. Frequently, such fires are analyzed by detecting anomalies like increased exhaust gas concentrations and soil temperatures at the surface. A proper analysis presumes the understanding of involved processes, which determine the spatial distribution and dynamic behavior of the anomalies.In this paper, we explain the relevance of mechanical and energy transport processes with respect to the occurrence of temperature anomalies at the surface. Two approaches are presented, aiming to obtain insight into the underground coal fire situation: In-situ temperature mapping and numerical simulation. In 2000 to 2005, annual temperature mapping in the Wuda (Inner Mongolia, PR China) coal fire area showed that most thermal anomalies on the surface are closely related to fractures, where hot exhaust gases from the coal fire are released. Those fractures develop due to rock mechanical failure after volume reduction in the seams. The measured signals at the surface are therefore strongly affected by mechanical processes.More insight into causes and effects of involved energy transport processes is obtained by numerical simulation of the dynamic behavior of coal fires. Simulations show the inter-relation between release and transport of thermal energy in and around underground coal fires. Our simulation results show a time delay between the coal fire propagation and the observed appearance of the surface temperature signal. Additionally, the overall energy flux away from the burning coal seam into the surrounding bedrock is about 30-times higher than the flux through the surface. This is of particular importance for an estimation of the energy released based on surface temperature measurements. Finally, the simulation results also prove that a fire propagation rate estimated from the interpretation of surface anomalies can differ from the actual rate in the seam.     

GMOs and their contexts: A comparison of potential and actual performance of GM crops in a local agricultural setting

In this paper, I argue that genetically modified organisms (GMOs) have inherent potential to contribute to socially and environmentally sustainable agriculture by virtue of their ‘biological embeddedness’. Their actual ‘performance’ and how this contributes to sustainability depends on the ‘mutual shaping’ of technology and context. While much attention has been given to the design context of GMOs, this paper considers the influence of the application context and of users. A case study investigating the use of insect-resistant and herbicide-tolerant GM cotton in the cotton-growing region of New South Wales in Australia is presented. The study was based on focus groups with farmers and other stakeholders in a cotton-growing community. It demonstrated a range of direct and indirect effects of GM cotton use, both positive and negative for sustainability, and the ways in which these effects were influenced by the local social context. The influences of the biotechnology industry context, in limiting the contributions that gene technologies can make to sustainability, were also considered, and remedies suggested. I argue that the polarity of the GM debate is hindering progress on these issues, and that a more balanced approach to our analysis of GMOs is necessary in order to fully understand, and to influence, their role in the future of rural spaces.     

Contribution of the SISCam Web-based GIS to the seismotectonic study of Campania (Southern Apennines): an example of application to the Sannio-area

In this article the implementation and potential of the Seismotectonic Information System of the Campania Region (SISCam) are described, in particular an application of this Web-based GIS system to the seismotectonic analysis of the Sannio area (Southern Apennines) is performed. WEB-GIS technologies greatly contribute to both the environmental monitoring and the disaster management of areas affected by high natural risks. Specifically the SISCam system has been developed with the aim of providing easy access and fast diffusion, through Internet technology, of the most significant geological, geophysical, and territorial data relative to the Campania Region. The Sannio area has been selected as our application example because it is among the most active seismic regions in Italy. This portion of the Southern Apennines which was hit by the June 5, 1688 strong earthquake (M _W = 6.7, CPTI 1999) and by some low- and moderate-energy seismic sequences (1990–1992, 1997), is characterized by a complex inherited tectonic setting and low-tectonic deformation rates that hide the seismogenic sources position. Since this case study turned out to be complicated, the use of the SIScam WEB-GIS has become indispensable because it allowed us to visualize, integrate and analyze all the data available, in order to obtain an accurate and direct picture of the seismotectonic setting of the area. Moreover, a different approach of data analysis was necessary, due to the lack of up-to-date neotectonic and structural data; therefore, the operation of this GIS system enabled us to process and generate some original informative layers, through image analysis, such as new structural lineaments represented on a map of the potential active faults of the area, which has been the final result of our application, as a contribution to new knowledge about the local seismic risk parameters.     

In situ strength measurements on natural upper-mantle minerals

Using in situ strength measurements at pressures up to 10 GPa and at room temperature, 400, 600, and 700°C, we examined rheological properties of olivine, orthopyroxene, and chromian-spinel contained in a mantle-derived xenolith. Mineral strengths were estimated using widths of X-ray diffraction peaks as a function of pressure, temperature, and time. Differential stresses of all minerals increase with increasing pressure, but they decrease with increasing temperature because of elastic strain on compression and stress relaxation during heating. During compression at room temperature, all minerals deform plastically at differential stress of 4–6 GPa. During subsequent heating, thermally induced yielding is observed in olivine at 600°C. Neither orthopyroxene nor spinel shows complete stress relaxation, but both retain some stress even at 700°C. The strength of the minerals decreases in the order of chromian-spinel ≈ orthopyroxene > olivine for these conditions. This order of strength is consistent with the residual pressure of fluid inclusions in mantle xenoliths.     

基于Mindlin理论Winkler地基参数的Kalman滤波识别

提出了Winkler地基参数的Kalman滤波识别方法。引入Mindlin理论后,推导了Winkler地基上板的控制微分方程。利用Fourier变换,推求了Winkler地基上简支板的Fourier闭式解。推导了Winkler地基参数的Kalman滤波方程,研究了Winkler地基参数的Kalman滤波识别的具体计算步骤。研究表明,运用Kalman滤波理论进行Winkler地基参数的识别,能有效地估计Winkler地基参数;Winkler地基参数的滤波收敛速度和精度受地基参数初始值选取和位移实测资料的影响,且Kalman滤波理论也可用于其他地基模型地基参数的识别。     

嵌入式Linux技术在海洋自动观测系统中的应用研究

随着Linux技术逐步走向成熟，嵌入式Linux技术在海洋自动观测系统中的应用将全面提高海洋观测系统整体性能，降低系统开发成本，进一步推进我国海洋自动观测系统产权自主化的建设。文章就如何研制适用于海洋自动观测系统的嵌入式Linux系统进行了论述。     

Artificial Upwelling of Deep Seawater Using the Perpetual Salt Fountain for Cultivation of Ocean Desert

Deep seawater in the ocean contains a great deal of nutrients. Stommel et al. have proposed the notion of a “perpetual salt fountain” (Stommel et al., 1956). They noted the possibility of a permanent upwelling of deep seawater with no additional external energy source. If we can cause deep seawater to upwell extensively, we can achieve an ocean farm. We have succeeded in measuring the upwelling velocity by an experiment in the Mariana Trench area using a special measurement system. A 0.3 m diameter, 280 m long soft pipe made of PVC sheet was used in the experiment. The measured data, a verification experiment, and numerical simulation results, gave an estimate of upwelling velocity of 212 m/day. This revised version was published online in July 2006 with corrections to the Cover Date.     

基于规则波波形的超声波非接触测量有关问题探讨

波浪波形的非接触测量近年来获得广泛的应用。本文以规则波为讨论对象，针对介质为空气的超声波测量方式进行波形测量误差分析，并结合实验室和实船试验进行对比分析。理论分析表明：在规则波取为坦谷波和ＳＴＯＫＥＳ波的前提下，超声波技术几乎产生相同的最大误差。定量分析表明，在对测量精度限制的条件下，对文中提及的各项参数应作有效的控制     

Field measurements and monitoring of wastewater discharge in sea water

This paper reports a study of the field measurements and monitoring of wastewater discharge in sea water at Bari East (Italy). A wastewater sea outfall system is an integral and fundamental part of each wastewater treatment with ultimate sink in the sea water. The design of a water treatment plant and wastewater outfall must take into account the use of the environmental water, the values of physicochemical parameters to be respected in order to safeguard the use itself and the quality of the environmental water where wastewater is issued. In the present study measurements of sea current velocity components were carried out with a VM-ADP (Vessel-Mounted Acoustic Doppler Profiler). Salinity, wind directions and velocities were assessed with, for one survey, the total faecal coliforms and other biochemical parameters. It was emphasized that the measurements necessary for monitoring cannot be concentrated in the wastewater outfall pipe zone only, but should be extended to a neighbouring area of the outfall pipe, with an extension depending on the wastewater discharge, the polluting charge and the magnitude of the sea currents and the winds typical of the zone of interest. The analyses presented in this paper confirm that the sea zones close to the wastewater outfall pipe are particularly sensitive and vulnerable. Such results must be considered in the planning of a wastewater outfall pipe.     

动态基准实时测量系统的开发与应用

介绍了动态基准实时测量系统的硬件组成、站点上全站仪棱镜组合安装与检测方法、系统软件的开发及特点，最后对系统在广州地铁某地铁站结构变形自动监测中的应用情况进行了阐述。通过实际应用表明该系统能应用在自动化、高精度的变形监测领域。