地物化方法在航磁异常查证中的应用

航磁异常查证是矿产勘查中的一个重要环节,其目的是通过地面查证,确定异常是否存在,追踪异常源,了解异常源所处的地质环境,对异常作出客观评价,提出进一步工作的建议,为后续资料解释提供依据.通过使用地物化综合方法对黑C-2011-02243号异常查证发现：地质剖面测量和土壤地球化学测量可在地表发现较好的找矿线索;高精度磁测及激电中梯测量则反映了深部地质体及矿化特征.依据查证结果认为,在进行航磁异常查证工作时,可优先进行剖面性的地质、高精度磁法及土壤地球化学测量工作;在分析上述测量结果的基础上安排剖面性的电法测量;如存在进一步找矿信息,可安排面积性物化探测量及工程验证工作.     

Magnetic measurements in electrical prospecting by resistivity methods

The electrical resistivity and induced polarization (IP) methods are widely used in geological mapping, prospecting and exploration of mineral deposits, engineering geology, hydrogeology, archaeology, and geotechnical and environmental applications. Historically, these methods have formed the basis of the electrical prospecting technique. In these methods, a DC or low-frequency AC electrical current is introduced into the earth through a grounded transmitter line. The measured quantity is the electric field. However, if the earth’s resistivity or chargeability changes horizontally, this change gives rise to an anomalous magnetic field, which is studied by the magnetometric resistivity (MMR) and magnetic induced polarization (MIP) methods, respectively. Along with advantages, some shortcomings are inherent in the MMR and MIP techniques. Apparently, the main drawback of these methods is that the magnetic fields of both the transmitter line wire and ground electrodes on the surface are several orders of magnitude greater than the anomalous magnetic field response. This introduces a significant “noise” to magnetic-resistivity data. We investigate the potential of using a circular electric dipole (CED) in magnetometric resistivity techniques. It has been found that the application of a CED, instead of a conventional transmitter line, dramatically enhances the signal-to-noise ratio.     

庐枞火山岩盆地南部拔茅山铜矿深部找矿潜力分析

位于庐枞火山岩盆地南部的拔茅山铜矿,是细脉带蚀变岩型脉状铜矿的代表。研究表明,其深部具有斑岩型铜矿的勘探潜力。为了进一步明确其深部找矿潜力,针对研究区斑岩型、热液型铜多金属矿的岩体、断裂、接触带等主要控矿因素,利用高精度磁法和可控源音频大地电磁测深(CSAMT)成果,分别对拔茅山岩体的分布、产状和深部形态及其与围岩的接触带特征进行了剖析。在此基础上,通过与沙溪斑岩铜矿地质、物探异常特征的类比,指明了研究区的找矿方向和有利找矿部位,为进一步找矿提供了思路和依据。     

基于航空重磁特征对突泉盆地构造的认识

为获取突泉盆地航空物探基础地质资料,为油气调查评价提供参考,中国国土资源航空物探遥感中心在该盆地开展了1:10万航空重磁综合调查工作。利用最新的航空重磁资料及实测岩石物性数据,对突泉盆地及其邻区重磁异常特征进行研究,分析航空重磁异常与地层展布、断裂活动、岩浆岩体的分布关系,重点探讨盆地的基底性质。结果表明,研究区航空重力异常与航磁异常在强度、范围、形态、梯度和走向等方面具有一定的规律性,该区断裂体系分布与重磁场特征明显相关,NNE-NE向、NW向及NE向3组断裂明显控制盆地沉积岩体及岩浆岩体的展布,盆地基底由下古生界浅变质岩系和前古生界中等变质岩系构成。     

Depositional setting,provenance, and tectonic-volcanic setting of Eocene–Recent deep-sea sediments of the oceanic Izu–Bonin forearc,northwest Pacific (IODP Expedition 352)

New biostratigraphical, geochemical, and magnetic evidence is synthesized with IODP Expedition 352 shipboard results to understand the sedimentary and tectono-magmatic development of the Izu–Bonin outer forearc region. The oceanic basement of the Izu–Bonin forearc was created by supra-subduction zone seafloor spreading during early Eocene (c. 50–51 Ma). Seafloor spreading created an irregular seafloor topography on which talus locally accumulated. Oxide-rich sediments accumulated above the igneous basement by mixing of hydrothermal and pelagic sediment. Basaltic volcanism was followed by a hiatus of up to 15 million years as a result of topographic isolation or sediment bypassing. Variably tuffaceous deep-sea sediments were deposited during Oligocene to early Miocene and from mid-Miocene to Pleistocene. The sediments ponded into extensional fault-controlled basins, whereas condensed sediments accumulated on a local basement high. Oligocene nannofossil ooze accumulated together with felsic tuff that was mainly derived from the nearby Izu–Bonin arc. Accumulation of radiolarian-bearing mud, silty clay, and hydrogenous metal oxides beneath the carbonate compensation depth (CCD) characterized the early Miocene, followed by middle Miocene–Pleistocene increased carbonate preservation, deepened CCD and tephra input from both the oceanic Izu–Bonin arc and the continental margin Honshu arc. The Izu–Bonin forearc basement formed in a near-equatorial setting, with late Mesozoic arc remnants to the west. Subduction-initiation magmatism is likely to have taken place near a pre-existing continent–oceanic crust boundary. The Izu–Bonin arc migrated northward and clockwise to collide with Honshu by early Miocene, strongly influencing regional sedimentation.     

Petrophysical characterisation of tight sandstone gas reservoirs using nuclear magnetic resonance: a case study of the upper Paleozoic strata in the Kangning area,eastern margin of the Ordos Basin,China

Residual and movable porosity are significant parameters for characterising petrophysical properties, especially in tight reservoirs. Eight tight sandstone samples from the upper Paleozoic gas-bearing strata in the Kangning area, from the eastern margin of the Ordos Basin, were analysed using nuclear magnetic resonance (NMR), scanning electron microscopy (SEM), petrography, and porosity and permeability tests. The lithology and pore types were identified and classified using petrography and SEM. The residual and movable porosity were obtained with NMR. In addition, NMR was used to visualise pore structure and pore size distribution. The results suggest that the upper Paleozoic sandstones in the study area mainly comprise feldspathic litharenite and litharenite. The sandstone porosity and permeability are low, with means of 5.9% and 0.549 mD, respectively. Four pore types exist in the tight sandstones: residual primary pores, grain dissolution pores, micropores (clay-dominated) and microfractures. The T₂ spectra under water-saturated conditions correlate with pore size and can be used to distinguish small and large pores based on the transverse relaxation time cutoff value of 10 ms, which corresponds to a pore diameter of 0.232 μm. Small pores account for 72% of the pores in the tight sandstones. The continuous bimodal T₂ spectra suggest good connectivity between small and large pores, despite the low porosity and permeability. In this study, the movable porosity of the major tight sandstone gas reservoirs is higher than the residual porosity, which confirms the effective evaluation of movable porosity to tight sandstone reservoirs, based on NMR experiments.     

青藏高原东部表土磁化率特征与环境意义

现代表土磁化率与气候因子关系的研究是黄土古气候重建的重要内容,在黄土高原地区取得了重要进展,但在青藏高原地区相对不足。在青藏高原东部系统采集了106个表土样品,分析了其磁化率的变化特征;并通过表土磁化率与气候因子的相关分析,讨论了气候因子对高原东部现代表土低频磁化率和频率磁化率的影响。结果表明：研究区表土磁化率特征主要受到温度和降水量的影响,水热组合差异影响表土磁化率值的高低。低频磁化率与气候因子的相关性较弱,总体上与温度的相关性优于降水量,可能表明其与气候因子的关系比较复杂;频率磁化率百分比与降水呈较好的正相关关系,表明该指标对降水量的变化更为敏感,可以用于青藏高原东部的古降水定量重建。     

藏南泽当地区大反向逆冲断层变形研究——以磁组构与EBSD组构分析为例

仁布-泽当逆冲断层是喜马拉雅大反向逆冲断层（GCT）在藏南地区的重要延伸部分,也是喜马拉雅造山带北部边界新生代最为活动的构造单元之一。新生代以来特提斯喜马拉雅的构造变形组构特征的研究对于深入理解碰撞造山带演化与高原隆升具有重要构造意义。本文综合GCT泽当-琼结段断层的宏观与微观变形特征,对断裂带石英脉、围岩中石英和云母矿物的电子背散射（EBSD）组构及断层两侧岩石磁组构（AMS）特征进行对比分析。结果表明对AMS主要贡献来自顺磁性云母、绿泥石等,磁化率各向异性椭球体以压扁状为主,磁面理与构造面理（劈理、断层面）基本重合,显示较强的构造变形磁组构特征;磁线理优选方向近南北向,且与观测北向逆冲断层方向一致,揭示剪切作用在变形过程中的持续作用。研究发现泽当地区GCT附近石英微观结构从围岩至断层区,石英至少呈现3种不同类型的微观变形机制：围岩区溶解蠕变、断裂带石英以膨凸重结晶和亚颗粒旋转重结晶作用为主。断裂带石英的c轴EBSD组构指示变形为低温（300~400℃）环境,其中黑云母的结晶学优选（CPO）与磁组构主轴优选方向存在高度的一致性,进一步证实了顺磁性矿物黑云母对AMS的主要贡献。综合研究表明泽当地区GCT的韧性变形是断层处在中上地壳韧性带的活动阶段变形的结果,也代表了特提斯喜马拉雅在碰撞、高原隆升期的变形主要特征。     

黑龙江省浅覆盖区地物化特征与找矿标志——以黑河市340高地金矿化区为例

黑龙江省黑河市340高地金矿点大地构造上位于兴安地块东北缘,多宝山Cu-Au-Mo-W-Fe成矿亚带内,其地貌为浅覆盖区,找矿较为困难。本文采用浅钻技术取样,对研究区进行基岩填图,圈定出以硅化为中心、青磐岩化为外围的蚀变矿化带。对基岩样品进行岩石地球化学分析,通过主成分分析,确定有6个主成分特征值大于1,其中第二主成分与金元素关系密切,是研究区有效的找矿标志。高精度磁测结果显示区内构造以NNW向为主,且其线性低值异常或与蚀变引起的退磁有关。对区内的地物化异常进行工程查证,发现金矿点1处,圈定预测靶区1处。     

Structural characteristics of the KPR-CBR triple-junction inferred from gravity and magnetic interpretations,Philippine Sea Plate

The intersection of the Kyushu-Palau Ridge (KPR) and the Central Basin Rift (CBR) of the West Philippine Basin (WPB) is a relic of a trench-trench-rift (TTR) type triple-junction, which preserves some pivotal information on the cessation of the seafloor spreading of the WPB, the emplacement and disintegration of the proto-Izu-Bonin-Mariana (IBM) Arc, and the transition from initial rifting to steady-state spreading of the Parece Vela Basin (PVB). However, the structural characteristics of this triple-junction have not been thoroughly understood. In this paper, using the newly acquired multi-beam bathymetric, gravity, and magnetic data obtained by the Qingdao Institute of Marine Geology, China Geological Survey, the authors depict the topographic, gravity, and magnetic characteristics of the triple-junction and adjacent region. Calculations including the upward continuations and total horizontal derivatives of gravity anomaly are also performed to highlight the major structural features and discontinuities. Based on these works, the morphological and structural features and their formation mechanisms are analyzed. The results show that the last episode amagmatic extension along the CBR led to the formation of a deep rift valley, which extends eastward and incised the KPR. The morphological and structural fabrics of the KPR near and to the south of the triple-junction are consistent with those of the western PVB, manifesting as a series of NNE-SSW- and N-S-trending ridges and troughs, which were produced by the extensional faults associated with the initial rifting of the PVB. The superposition of the above two reasons induced the prominent discontinuity of the KPR in deep and shallow crustal structures between 15°N–15°30′N and 13°30′N–14°N. Combined with previous authors’ results, we propose that the stress produced by the early spreading of the PVB transmitted westward and promoted the final stage amagmatic extension of the CBR. The eastward propagation of the CBR destroyed the KPR, of which the magmatism had decayed or ceased at that time. The destruction mechanism of the KPR associated with the rifting of the PVB varies along strike the KPR. Adjacent to the triple-junction, the KPR was destroyed mainly due to the oblique intersection of the PVB rifting center. Whereas south of the triple-junction, the KPR was destroyed by the E-W-directional extensional faulting on its whole width.©2021 China Geology Editorial Office.