轴压比对中等高度LC结构剪力墙抗震性能的影响

轻骨料混凝土(L ight-we ight concrete,简称LC)剪力墙的轴压比是剪力墙抗震设计时一个重要的控制因素,直接关系到其延性性能。为使设计规程具有足够的理论依据,本文通过对六榀轻骨料混凝土剪力墙试件的试验,研究了在低周反复荷载作用下,着重考虑不同轴压比对中等高度有边框剪力墙的破坏形态和变形性能的影响效应,对其滞回特性进行分析,计算了各剪力墙的刚度退化率与延性系数,并将无竖缝剪力墙与带竖缝剪力墙的抗震性能进行了对比。     

建立回弹现场测强曲线的位置参数法

工程上迫切需要在现场数据较少的情况下,建立高精度和高可靠度的现场测强曲线(经验公式)。本文利用位置参数法,提出了一种回弹法现场测强曲线(经验公式)。此曲线(经验公式)仍运用原有的幂函数形式并保持回归参数不变,通过增加位置参数反映现场试验的个性信息。此曲线(经验公式)融合了所在地区混凝土强度值、回弹值、碳化深度值之间的共性趋势和现场检测得到的反映现场情况的个性信息,而且解决了地区测强曲线(经验公式)不能完全描述现场的实际情况,而现场检测数据一般不能满足制定现场专用测强曲线(经验公式)要求的问题。在建筑结构无损检测中,利用本文提出的测强曲线(经验公式)可以极大地提高检测精度和检测结果的可靠性,使检测结果更加符合施工现场的实际情况。     

消能减震高层方钢管混凝土框架结构振动台试验研究和弹塑性时程分析

本文首先介绍了一幢安装了粘滞阻尼器的复杂体型高层方钢管混凝土框架结构的1/15缩尺模型的模拟地震振动台试验结果;在此基础上,建立了梁、柱构件的多弹簧模型并组建了整体结构的计算分析模型,运用此计算模型首先对试验模型结构进行了动力弹塑性时程分析,计算结果和试验结果吻合较好,验证了计算模型的正确性;最后,以同样方法对原型结构进行了计算分析,并结合试验结果研究探讨了此结构的抗震性能和阻尼器的消能减震效果。结果表明:该结构未出现明显的薄弱层,能够满足规范的抗震设防要求,阻尼器发挥了一定的消能减震效果,进一步提高了结构的抗震性能。     

基于能量原理的钢筋混凝土简体结构抗震性能研究

本文通过能量法研究了钢筋混凝土简体结构的抗震性能。文中采用振型分解法按等效单自由度体系求解简体结构的滞回输入能;用pushover法分析了滞回耗能在结构层间的分布规律及结构自身的耗能能力;根据楼层滞回耗能与弹塑性层间位移的关系求出了薄弱层的弹塑性位移。对一高层钢筋混凝土框架-简体结构在7度罕遇地震下的抗震性能进行了评估,通过与非线性动力时程分析的对比,证明了方法的可行性。     

超高强混凝土短柱抗震性能的试验研究

通过对12根剪跨比λ=2．0的超高强混凝土短柱在低周反复荷载下抗震性能的试验研究,分析了其破坏形态,并研究了轴压比和配箍率对试件滞回特性和抗震延性的影响,提出了满足一定延性要求（μ△≥3．0）超高强混凝土短柱的轴压比限值和箍筋加密区的最小配箍特征值的建议值。该值可为现行规范的修订提供参考。     

An evaluation of force-based design vs. direct displacement-based design of jointed precast post-tensioned wall systems

The unique features of jointed post-tensioned wall systems, which include minimum structural damage and re-centering capability when subjected to earthquake lateral loads, are the result of using unbonded post-tensioning to attach the walls to the foundation, along with employing energy dissipating shear connectors between the walls. Using acceptance criteria defined in terms of inter-story drift, residual drift, and floor acceleration, this study presents a multiplelevel performance-based seismic evaluation of two five-story unbonded post-tensioned jointed precast wall systems. The design and analysis of these two wall systems, established as the direct displacement-based and force-based solutions for a prototype building used in the PREcast Seismic Structural Systems （PRESSS） program, were performed at 60% scale so that the analysis model could be validated using the PRESSS test data. Both buildings satisfied the performance criteria at four levels of earthquake motions although the design base shear of the direct displacement-based jointed wall system was 50% of that demanded by the force-based design method. The study also investigated the feasibility of controlling the maximum transient inter-story drift in a jointed wall system by increasing the number of energy dissipating shear connectors between the walls but without significantly affecting its re-centering capability.     

Mechanical compression release device in steel bracing system for retrofitting RC frames

1 Introduction Braced steel frames are commonly used to resist seismic loads. Their seismic behavior was extensively studied during the past decades (Bertero et al.., 1989; Roeder, 1989; Jain, 1978). Their design is governed by the buckling behavior of the bracing members (ASCE, 1994,2002; CSA, 1994). To prevent or delay the seismic buckling of compressive members in concentrically braced frames in steel structures, a great number of methods have been proposed. These include the use of sp…     

Flexural performances of prestressed high strength concrete piles reinforced with hybrid GFRP and steel bars

Abstract

This study developed prestressed high-strength concrete (PHC) piles reinforced with high-strength materials (glass fiber-reinforced polymer (GFRP) bars) for flexural performance enhancement. Flexural strengths and behaviors of PHC piles reinforced with hybrid GFRP and steel bars were experimentally investigated, respectively. Large-scale specimens with total lengths of 12,000?mm and diameters of 600?mm were constructed and tested under bending, accompanied by evaluation of effects of non-prestressed reinforcement type and longitudinal reinforcement ratio. J-factors were calculated to evaluate deformability of all the specimens. PHC piles reinforced with GFRP bars were demonstrated to have much higher flexural capacity than those reinforced with steel bars. Moreover, strains at the midspans of cross sections of all the specimens basically conformed to the assumption of plane section. Failure of PHC piles reinforced with GFRP bars was attributable to gradual concrete crushing, while that of PHC piles reinforced with steel bars resulted from steel yielding. Results of this study were expected to provide theoretical basis for wide engineering applications of PHC piles reinforced with hybrid GFRP bars and steel bars in marine structures.     

海水海砂混凝土双K断裂参数的确定

采用尺寸为515 mm×100 mm×100 mm初始缝高比从0.1变化至0.8的三点弯曲梁试件,利用试验测得起裂荷载Pini、最大荷载Pmax及对应的裂缝口张开位移CMODc等参数,研究了缝高比a0/h对海水海砂混凝土双K断裂参数的影响。并以相同配合比的淡水河砂梁作为对照组,进一步研究了海砂海水混凝土双K断裂参数与普通混凝土之间的关系。结果发现海水海砂混凝土断裂参数在a0/h=0.25～0.7范围内时可以认为是一常数;海水海砂混凝土梁断裂参数比相同配合比情况下的淡水河砂梁大且对边界影响更加敏感。     

海上孤立混凝土构筑物的爆破拆除

在海洋工程中,采用爆破手段拆除海上孤立混凝土构筑物或清理孤立大块石是一种快速、有效的方法。文中详细介绍了爆破方案的确定、爆破孔网参数的设计、爆破药量的计算以及安全防护措施,对于类似工程的实施具有重要的参考价值。