Pseudodynamic tests on rubber base isolators with numerical substructuring of the superstructure and strain‐rate effect compensation

A pseudodynamic testing procedure has been applied by which the seismic response of a base‐isolated building is obtained by using as specimen the isolators, while the superstructure is numerically simulated. The procedure also takes advantage of the continuous pseudodynamic testing capabilities of the ELSA laboratory, which increase the accuracy of the results and reduce the strain‐rate effect of the rubber bearings. A simple proportional correction of the measured forces compensates the remaining strain‐rate effect due to the unrealistic speed of the test. The correction factor is obtained by means of a characterizing test on the specific rubber isolators. The developed method has been successfully applied to the prediction of the seismic response of a base‐isolated four‐storey building submitted to several specified accelerograms. The results for those earthquakes as well as the effects of some changes of the parameters of the system are discussed. Copyright © 2002 John Wiley & Sons, Ltd.     

Towards a direct collapse–load method of design for concrete frames subjected to severe ground motions

Most current methods of design for concrete structures under earthquake loads rely on highly idealized ‘equivalent’ static representations of the seismic loads and linear‐elastic methods of structural analysis. With the continuing development of non‐linear methods of dynamic analysis for the overload behaviour and collapse of complete concrete structures, a more direct and more accurate design procedure becomes possible which considers conditions at system collapse. This paper describes an evaluation procedure that uses non‐linear dynamic collapse–load analysis together with global safety coefficients. A back‐calibration procedure for evaluating the global safety coefficients is also described. The aim of this paper is to open up discussion of alternative methods of design with improved accuracy which are necessary to move towards a direct collapse–load method of design. Copyright © 2002 John Wiley & Sons, Ltd.     

Damaging properties of ground motions and prediction of maximum response of structures based on momentary energy response

Dynamic damaging potential of ground motions must be evaluated by the response behaviour of structures, and it is necessary to indicate what properties of ground motions are most appropriate for evaluation. For that purpose, the behaviour of energy input process and hysteretic energy dissipation are investigated in this study. It is found that the momentary input energy that is an index for the intensity of input energy is related to the characteristics of earthquakes such as cyclic or impulsive, and to the response displacement of structures immediately. On the basis of these results, a procedure is proposed to predict inelastic response displacement of structures by corresponding earthquake input energy to structural dissipated damping and hysteretic energy. In this procedure the earthquake response of structures is recognized as an input and dissipation process of energy, and therefore structural properties and damaging properties of ground motions can be taken into account more generally. Lastly, the studies of the pseudodynamic loading test of reinforced concrete structure specimens subjected to ground motions with different time duration are shown. The purpose of this test is to estimate the damaging properties of ground motions and the accuracy of the proposed prediction procedure. Copyright © 2002 John Wiley & Sons, Ltd.     

Study on effects of damping in laminated rubber bearings on seismic responses for a ⅛ scale isolated test structure

The effects of damping in various laminated rubber bearings (LRB) on the seismic response of a ?‐scale isolated test structure are investigated by shaking table tests and seismic response analyses. A series of shaking table tests of the structure were performed for a fixed base design and for a base isolation design. Two different types of LRB were used: natural rubber bearings (NRB) and lead rubber bearings (LLRB). Three different designs for the LLRB were tested; each design had a different diameter of lead plug, and thus, different damping values. Artificial time histories of peak ground acceleration 0.4g were used in both the tests and the analyses. In both shaking table tests and analyses, as expected, the acceleration responses of the seismically isolated test structure were considerably reduced. However, the shear displacement at the isolators was increased. To reduce the shear displacement in the isolators, the diameter of the lead plug in the LLRB had to be enlarged to increase isolator damping by more than 24%. This caused the isolator stiffness to increase, and resulted in amplifying the floor acceleration response spectra of the isolated test structure in the higher frequency ranges with a monotonic reduction of isolator shear displacement. Copyright © 2002 John Wiley & Sons, Ltd.     

Active viscous damping system with amplifying braces for control of MDOF structures

The development and the applications of an active controlled viscous damping device with amplifying braces are described. The system of the dampers, defined as active viscous damping system (AVDS), connected to an amplifying brace (AB) is presented herein. Instantaneous control theory with velocity and acceleration feedback is used to obtain the control forces at each time step during an excitation. Control of the damping forces is possible due to the mechanical structure of the proposed AVDS, and the connection to the AB. The proposed system can be efficiently used to enhance the damping of a structure without modifying its stiffness. The added damping forces can be adjusted in a wide range. The efficiency of the presented system is demonstrated by a numerical simulation of a seven‐storey building subjected to earthquakes. The simulation shows a considerable reduction of control forces required for control to the AVDS with AB, compared to the same system without AB. Copyright © 2002 John Wiley & Sons, Ltd.     

海底天然气渗漏形成水合物量的线性动力学模型:以墨西哥湾GC185区块Bush高地为例

世界许多地区如墨西哥湾，存在着大量天然气渗漏并形成水合物的现象，出于科学，生态，气候和安全的需要。人类有必要弄清存在于海底以水合成形式存在的天然气的比例。因此，构建了水合物形成量的线性动力学模型，以分析墨西哥湾GC185块区Bush高地海底渗漏天然气的地质过程和行为。Bush高地渗漏的天然气来源于附近的Jolliet气藏，结果表明，渗漏天然气中约有9％的海底形成了水合物。     

Viscous damping formulation and high frequency motion propagation in non-linear site response analysis

Non-linear time domain site response analysis is widely used in evaluating local soil effects on propagated ground motion. This approach has generally provided good estimates of field behavior at longer periods but has shortcomings at relatively shorter periods. Viscous damping is commonly employed in the equation of motion to capture damping at very small strains and employs an approximation of Rayleigh damping using the first natural mode only. This paper introduces a new formulation for the viscous damping using the full Rayleigh damping. The new formulation represents more accurately wave propagation for soil columns greater than 50 m thick and improves non-linear site response analysis at shorter periods. The proposed formulation allows the use of frequency dependent viscous damping. Several examples, including a field case history at Treasure Island, California, demonstrate the significant improvement in computed surface response using the new formulation.     

非线性地球物理反演方法:回顾与展望

自20世纪90年代以来，非线性地球物理反演方法已走向成熟，这些方法包括线性化迭代法，仿真淬火法，遗传算法及联合反演方法等，线性化迭代反演基于开放物理系统状态发生相变的原理，要进一步改善模型参数化的技术和迭代过程的自组织；仿真淬火法与遗传算法基于自然过程的指数率或生物演化的优生率，可以相互结合以提高解估计的分辨率与置信度；联合反演要结合岩石物理性质的统计规律，才能取得兼容地质与综合方法的应用效果，地球动力学中的反问题不仅涉及偏微分方程系数项的求解，而且涉及初始条件或初始边界的求解，对地球动力学作用过程研究特别重要。     

导管架式海洋平台结构阻尼隔振体系及其减振效果分析

导管架式海洋平台结构是当前应用最广的一种平台结构形式。本文研究导管架式海洋平台结构阻尼隔振体系及其减振效果。针对导管架式海洋平台结构的型式与特点，为了充分发挥阻尼器的耗能减振作用，提出了在平台结构导管架端帽和甲板之间设置柔性阻尼层的新型阻尼隔振方案。针对渤海JZ20－2MUQ平台结构，建立了海洋平台结构阻尼隔振体系简化计算模型，研究了隔振层参数与结构阻尼比的关系以及它们对结构整体和隔振层层间相对位移的控制效果；进行了多种冰荷载工况和地震工况的数值模拟。结果表明，阻尼隔振方案是导管架式海洋平台结构的一种有效的减振措施。     

铅橡胶复合阻尼器的性能试验研究

介绍作者提出的铅橡胶复合阻尼器的构造与耗能原理，通过不同形状，不同大小铅心的8个铅橡胶复合阻尼器的循环荷载试验，研究了频率、应变幅值、循环次数、铅芯直径、竖向压力等对铅橡胶复合阻尼器的影响规律。研究结果表明，铅橡胶复合阻尼器工作性能稳定，耗能性能和抗疲劳性能好。