Numerical Simulation on Flow Past Two Side-by-Side Inclined Circular Cylinders at Low Reynolds Number

A series of three-dimensional numerical simulations is carried out to investigate the effect of inclined angle on flow behavior behind two side-by-side inclined cylinders at low Reynolds number Re=100 and small spacing ratio T/D=1.5 (T is the center-to-center distance between two side-by-side cylinders, D is the diameter of cylinder). The instantaneous and time-averaged flow fields, force coefficients and Strouhal numbers are analyzed. Special attention is focused on the axial flow characteristics with variation of the inclined angle. The results show that the inclined angle has a significant effect on the gap flow behaviors behind two inclined cylinders. The vortex shedding behind two cylinders is suppressed with the increase of the inclined angle as well as the flip-flop gap flow. Moreover, the mean drag coefficient, root-mean-square lift coefficient and Strouhal numbers decrease monotonously with the increase of the inclined angle, which follows the independent principle at small inclined angles.     

钙质土中重力串锚水平承载力特性有限元研究

目前没有规范给出串锚的水平承载力计算公式,为了利用有限元法研究串锚水平承载力特性,采用相关理论计算以及室内试验的方法来验证有限元法模拟计算的可靠性。实践证明,有限元法具有较高的计算精度。利用有限元分析软件ABAQUS建立了串锚-土体模型,模拟串锚在水平荷载作用下破坏过程,研究了串锚在水平荷载作用下破坏机理,从而得到了串锚水平承载力特性。在相同的工况条件下,串锚的水平承载力与其锚链长度有关,在一定范围内,增加锚链的长度可以提高串锚的水平承载力;串锚的水平承载力不是相应的单个锚的水平承载力相加,其水平承载力小于相应的单个锚水平承载力之和,在进行串锚水平承载力设计计算时应给与相应的考虑。     

陀螺全站仪在隧道测量中的应用研究

随着我国经济和科技的蓬勃发展,隧道工程建设也呈现出规模化和多元化的趋势。本文首先总结了我国公路隧道、铁路隧道和水下隧道的增长状况;然后归纳了隧道测量中平面控制网的布设方法;最后通过分析发现:通过陀螺全站仪加测陀螺边来传递方位基准,可有效提高隧道贯通精度。     

三杯风速传感器非水平风场测量性能

为解决三杯风速传感器在计量检定条件下与观测场景中环境差异所导致的测量数据误差,致力于研究空气流速计量标准在量值传递过程中的真实性、准确性和一致性,为新一代三杯风速传感器作为计量器具的新产品型式评价提供思路和参考指标,依据杯式测风仪测量方法与自动气象站风速风向传感器检定规程,并在实验中加入了主体由角度编码器构成的自动化转盘系统,设计了三杯风速传感器在非水平风场内测量性能水平实验。通过调整三杯风速传感器在风洞试验段内的倾斜角度,模拟其在自然界非水平风场中的测量状态,同步采集风洞的标准指示风速、三杯风速传感器的实测风速以及其相应的倾斜角度,计算示值误差,利用方差分析、趋势分析、相关性分析和线性回归分析等统计方法,对不同倾斜角度下三杯风速传感器示值误差进行研究,得出了三杯风速传感器在风洞试验段内的示值误差与实测风速和倾斜角度之间的相关关系,提出了三杯风速传感器在非水平风场下的测量性能指标。研究了三杯风速传感器在非水平风场中实测风速与标准风速和倾斜角度的回归关系,提出了三杯风速传感器在计量环境下非水平风场中数据的量值传递修正算法。     

Estimates of global M_2 internal tide energy fluxes using TOPEX/POSEIDON altimeter data

TOPEX/POSEIDON altimeter data from October 1992 to June 2002 are used to calculate the global barotropic M2 tidal currents using long-term tidal harmonic analysis. The tides calculated agree well with ADCP data obtained from the South China Sea (SCS). The maximum tide velocities along the semi-major axis and semi-minor axis can be computed from the tidal ellipse. The global distribution of M2 internal tide vertical energy flux from the sea bottom is calculated based on a linear internal wave generation model. The global vertical energy flux of M2 internal tide is 0.96 TW, with 0.36 TW in the Pacific, 0.31 TW in the Atlantic and 0.29 TW in the Indian Ocean, obtained in this study. The total horizontal energy flux of M2 internal tide radiating into the open ocean from the lateral boundaries is 0.13 TW, with 0.06 TW in the Pacific, 0.04TW in the Atlantic, and 0.03 TW in the Indian Ocean. The result shows that the principal lunar semi-diurnal tide M2 provides enough energy to maintain the large-scale thermohaline circulation of the ocean.     

Urban three-dimensional expansion and its driving forces —A case study of Shanghai, China

Urban expansion is a phenomenon of urban space increase, and an important measuring index of the process of urbanization. Taking Shanghai as an example, the changes of urban average height and built-up area were studied to represent city’s vertical and horizontal increases respectively, and statistical methods were used to analyze the driving forces of urban expansion. The research drew following conclusions: 1) The urban expansion process of Shanghai from 1985 to 2006 had a clear periodic feature, and could be divided into three stages: vertical expansion in dominance, coordinated vertical and horizontal expansion, and horizontal expansion in dominance. 2) The average height and quantity of buildings in core city were significantly bigger than those in suburbs, but the changing speed of the latter was faster. And 3) urbanization process was the major driving force for the city’s horizontal expansion, while industrial structure improvement was the key driving factor for the vertical expansion. Those two driving forces were simultaneously affected by city’s political factors.     

轨道平顺性与测量精度

从轨道平顺性验收标准性切入,提出轨道平顺性对控制网的精度要求;指出轨道平顺性与控制点间的相对精度相关,与控制测量网垂直于线路的的横向误差及高程相关。     

Buckling of multi-segment underwater pressure hull

Results of a numerical and experimental study into buckling performance of multi-segment pressure hull subjected to uniform hydrostatic pressure are discussed. Constituents of multi-segment configurations are bowed-out cylindrical shells with, and without flanges. Details about five collapse tests of laboratory scale mild steel, CNC machined models are given. Segments were about 200 mm diameter, 100 mm long and had uniform wall thickness of 3 mm. Experimental collapse pressures were in the range from 12 to 20 MPa. Numerical collapse pressures agreed well with those obtained during experiments.     

Hydrodynamic performance of a dual cylindrical caisson breakwater

The hydrodynamic performance of a dual cylindrical caisson breakwater (DCBW) formed by a row of caissons each of which consisting of a porous outer cylinder circumscribing an impermeable inner cylinder has been theoretically investigated. The theoretical formulation is based on the eigenfunction expansion method proposed by Spring and Monkmeyer (1974) which was further modified by Linton and Evans [Linton, C.M., Evans, D.V., 1990. The interaction of waves with arrays of vertical circular cylinders. Journal of Fluid Mechanics 215, 549–569] for an array of impermeable cylinders. The present formulation is an extension of the work of Wang and Ren [Wang, K.H., Ren, X., 1994. Wave interaction with a concentric porous cylinder system. Ocean Engineering 21(4), 343–360], wherein; the interaction of linear waves with a single concentric porous cylinder system was studied. In the present study, the formulation has been extended to the case of a group of porous dual cylinder system. Parametric studies are carried out to study the influence of porosity (G₀) on the outer caisson, width of the doughnut chamber (a/b) and the angle of wave incidence on the variation in the hydrodynamic loading, wave run-up, free-surface elevation in its vicinity as well as the transmission on its lee-side. The importance of the presence of the inner cylinder in achieving the required hydrodynamic performance in terms of either protection or providing tranquility on its lee side keeping higher stability for the breakwater system is highlighted.     

基于正交试验的水平井射孔参数优化设计

目前水平井射孔完井已在国内外各油田取得了广泛的应用,射孔参数的优化是水平井经济、高效生产运行的关键。在建立了基于正交试验的水平井射孔参数优化设计模型的基础上,研究并筛选了影响水平井射孔完井产能的9个主要因素,分析了各因素对水平井产能影响的权重,优化了射孔完井参数方案,为水平井射孔参数优化提供了新的方法和技术支持。