超声与振荡提取沉积物中松散结合态磷的比较

用超声技术提取沉积物样品中松散结合态磷,并与振荡提取结果进行比较。结果表明,超声提取结果与振荡提取结果大致相当。超声提取耗时短,操作简单易行,测试结果精密度为3.8%(RSD,n=7),可以替代振荡方法提取沉积物中的松散结合态磷。     

贵州大方县公鸡山地裂缝特征成因及防治

文章通过对贵州省大方县以公鸡山地裂隙实地调查，认为地裂隙的形成主要与公鸡山一带地下采煤有关。即采煤虚脱，沿先存构造断裂拉张而成。同时叙述了地裂缝特征及危害，并提出防灾减灾措施。     

山东省临邑县临盘镇地裂冒喷水油灾害初步分析

1998年7月临邑县临盘镇西十二里村发生地裂冒喷水油灾害：对此次灾害研究认为，灾害发生前地应力已有明显改变，这种改变应是自然因素造成的，油田开发难以直接引发断层的活动。因此，地裂冒喷水、油灾害是因活动性断昙——临邑断层在局部薄弱部位活动而引起的，断层活动使地下流体顺断层涌出地表，是自然地质灾害。灾害的诱发因素是多方面的，其中地面不均衡沉降耦合使得地下应力布不均习，导致在断层的薄弱部位产生应力集中，并引发灾害发生。灾害发生已使得地下不均衡应力得以释放，近期内再次发生灾害的可能性不大。     

地下圆形衬砌隧道对沿线地震动的影响(II):数值结果

利用地下圆形衬砌隧道对入射平面P波和SV波散射级数解答，定量分析了入射波长、入射角度、隧道直径、衬砌刚度等因素对沿线地表位移放大作用的影响。计算结果表明，当入射频率较低时，地下隧道的存在对地表位移幅值影响不大；而当入射频率较高时，地表位移幅值可以达到无隧道情况的4．5倍以上；衬砌情况下地表位移幅值可以高出非衬砌情况的87．8％。建议在地铁的规划设计中考虑地下隧道的建设对隧道沿线设计地震动的影响。     

地下水资源管理预警系统的建立及应用研究——以长春城区为例

由于长春城区地下水的超采产生了环境恶化,结合地下水预测模型和地质及水文地质条件,以长春城区为例建立了地下水资源管理预警模型。根据长春城区的地质及水文地质条件提出水位水质预警标准,并根据模型编制了地下水资源管理预警系统。利用所建立的预警系统,对现状和未来开采条件下水位水质进行预警,从而为水资源的科学管理和持续利用提供可靠依据和保障。     

A mathematical hysteretic model for elastomeric isolation bearings

An analytical model for high damping elastomeric isolation bearings is presented in this paper. The model is used to describe mathematically the damping force and restoring force of the rubber material and bearing. Ten parameters to be identified from cyclic loading tests are included in the model. The sensitivity of the ten parameters in affecting the model is examined. These ten parameters are functions of a number of influence factors on the elastomer such as the rubber compound, Mullins effect, scragging effect, frequency, temperature and axial load. In this study, however, only the Mullins effect, scragging effect, frequency and temperature are investigated. Both material tests and shaking table tests were performed to validate the proposed model. Based on the comparison between the experimental and the analytical results, it is found that the proposed analytical model is capable of predicting the shear force–displacement hysteresis very accurately for both rubber material and bearing under cyclic loading reversals. The seismic response time histories of the bearing can also be captured, using the proposed analytical model, with a practically acceptable precision. Copyright © 2002 John Wiley & Sons, Ltd.     

Optimum multiple tuned mass dampers for structures under the ground acceleration based on DDMF and ADMF

Multiple tuned mass dampers (MTMD) consisting of many tuned mass dampers (TMDs) with a uniform distribution of natural frequencies are taken into consideration for attenuating undesirable vibration of a structure under the ground acceleration. A study is conducted to search for the preferable MTMD which performs better and is easily manufactured from the five available models (i.e. MTMD‐1 – MTMD‐5), which comprise various combinations of the stiffness, mass, damping coefficient and damping ratio in the MTMD. The major objective of the present study then is to evaluate and compare the control performance of these five models. The structure is represented by its mode‐generalized system in the specific vibration mode being controlled by adopting the mode reduced‐order approach. The optimum parameters of the MTMD‐1 – MTMD‐5 are investigated to reveal the influence of the important parameters on their effectiveness and robustness using a numerical searching technique. The parameters include the frequency spacing, average damping ratio, tuning frequency ratio, mass ratio and total number. The criteria selected for the optimum searching are the minimization of the maximum value of the displacement dynamic magnification factor (DDMF) and that of the acceleration dynamic magnification factor (ADMF) of the structure with the MTMD‐1 – MTMD‐5 (i.e. Min.Max.DDMF and Min.Max.ADMF). It is demonstrated that the optimum MTMD‐1 and MTMD‐4 yield approximately the same control performance, and offer higher effectiveness and robustness than the optimum MTMD‐2, MTMD‐3, and MTMD‐5 in reducing the displacement and acceleration responses of structures. It is further demonstrated that for both the best effectiveness and robustness and the simplest manufacturing, it is preferable to select the optimum MTMD‐1. Copyright © 2002 John Wiley & Sons, Ltd.     

Towards a direct collapse–load method of design for concrete frames subjected to severe ground motions

Most current methods of design for concrete structures under earthquake loads rely on highly idealized ‘equivalent’ static representations of the seismic loads and linear‐elastic methods of structural analysis. With the continuing development of non‐linear methods of dynamic analysis for the overload behaviour and collapse of complete concrete structures, a more direct and more accurate design procedure becomes possible which considers conditions at system collapse. This paper describes an evaluation procedure that uses non‐linear dynamic collapse–load analysis together with global safety coefficients. A back‐calibration procedure for evaluating the global safety coefficients is also described. The aim of this paper is to open up discussion of alternative methods of design with improved accuracy which are necessary to move towards a direct collapse–load method of design. Copyright © 2002 John Wiley & Sons, Ltd.     

Damaging properties of ground motions and prediction of maximum response of structures based on momentary energy response

Dynamic damaging potential of ground motions must be evaluated by the response behaviour of structures, and it is necessary to indicate what properties of ground motions are most appropriate for evaluation. For that purpose, the behaviour of energy input process and hysteretic energy dissipation are investigated in this study. It is found that the momentary input energy that is an index for the intensity of input energy is related to the characteristics of earthquakes such as cyclic or impulsive, and to the response displacement of structures immediately. On the basis of these results, a procedure is proposed to predict inelastic response displacement of structures by corresponding earthquake input energy to structural dissipated damping and hysteretic energy. In this procedure the earthquake response of structures is recognized as an input and dissipation process of energy, and therefore structural properties and damaging properties of ground motions can be taken into account more generally. Lastly, the studies of the pseudodynamic loading test of reinforced concrete structure specimens subjected to ground motions with different time duration are shown. The purpose of this test is to estimate the damaging properties of ground motions and the accuracy of the proposed prediction procedure. Copyright © 2002 John Wiley & Sons, Ltd.     

Study on effects of damping in laminated rubber bearings on seismic responses for a ⅛ scale isolated test structure

The effects of damping in various laminated rubber bearings (LRB) on the seismic response of a ?‐scale isolated test structure are investigated by shaking table tests and seismic response analyses. A series of shaking table tests of the structure were performed for a fixed base design and for a base isolation design. Two different types of LRB were used: natural rubber bearings (NRB) and lead rubber bearings (LLRB). Three different designs for the LLRB were tested; each design had a different diameter of lead plug, and thus, different damping values. Artificial time histories of peak ground acceleration 0.4g were used in both the tests and the analyses. In both shaking table tests and analyses, as expected, the acceleration responses of the seismically isolated test structure were considerably reduced. However, the shear displacement at the isolators was increased. To reduce the shear displacement in the isolators, the diameter of the lead plug in the LLRB had to be enlarged to increase isolator damping by more than 24%. This caused the isolator stiffness to increase, and resulted in amplifying the floor acceleration response spectra of the isolated test structure in the higher frequency ranges with a monotonic reduction of isolator shear displacement. Copyright © 2002 John Wiley & Sons, Ltd.