A note on the lake level variations of Nam Co,south-central Tibetan Plateau from 2005 to 2019

Tibetan lake levels are sensitive to global change, and their variations have a large impact on the environment, local agriculture and animal husbandry practices. While many remote sensing data of Tibetan lake level changes have been reported, few are from in-situ measurements. This note presents the first in-situ lake level time series of the central Tibetan Plateau. Since 2005, daily lake level observations have been performed at Lake Nam Co, one of the largest on the Tibetan Plateau. The interannual lake level variations show an overall increasing trend from 2006 to 2014, a rapid decrease from 2014 to 2017, and a surge from 2017 to 2018. The annual average lake level of the hydrological year (May-April) rose 66 cm from 2006 to 2014, dropped 59 cm from 2014 to 2017, and increased 20 cm from 2017 to 2018, resulting in a net rise of 27 cm or an average rate of about 2 cm per year. Compared to the annual average lake level based on the calendar year, it is better to use the annual average lake level based on the hydrological year to determine the interannual lake level changes. As the lake level was stable in May, it is appropriate to compare May lake levels when examining interannual lake level changes with fewer data. Overall, remote sensing results agree well with the in-situ lake level observations; however, some significant deviations exist. In the comparable 2006-2009 period, the calendar-year average lake level observed in-situ rose by 10-11 cm per year, which is lower than the ICESat result of 18 cm per year.     

激光跟踪仪在核电站主管道安装中的应用

目前,核电站的主管道焊接越来越多的采用了自动焊技术,这有利于提高焊接质量效率,还可以压缩建设成本。然而,主管道自动焊对焊缝的限差较现有工艺要求更高,高精度的测量是实现主管道自动焊的必要条件之一。本文针对主管道自动焊管口组队高精度的技术要求,提出采用激光跟踪仪对主管道自动焊相关的设备进行更为精密的三维工业测量,通过理论技术评定测量精度,然后选择测量仪器和编制具体的测量方案,最终保证了主管道自动焊精确组对的实现。     

移动测量技术在城市绿化普查中的应用

在新时代的城市建设中,绿化建设对于美化城市面貌和提高市民居住舒适度显得十分重要,那么城市绿化普查工作则成为绿化建设工作中的重要一环。为了改进传统绿化普查工作,本文提供一整套基于移动测量技术的城市绿化普查方案,搭配自主研发的GIS采集软件和实景三维管理平台,采集绿化信息的效率和精度显著提高,更可以优化城市绿化管理方法。     

冲绳海槽浮岩包裹体的测温试验

对浮岩中斜长石斑晶中的包裹体及玻璃基质中的包裹体首先进行双面光薄片的镜下观察，然后进行了系统的均化法与爆裂法测温试验。观察与试验结果表明：(1)斜长石中的包裹体均为玻璃质+气泡的两相包裹体，未发现气—液包裹体。固化包裹体为玻璃质，非晶质的固化包裹体外即是大量的气泡，特别是基质当中气泡更为发育，说明熔浆中含有丰富的挥发性组分，同时也说明包裹体形成于较浅的地质条件下。(2)长石中包裹体的均化温度不受包裹体特征不同的影响，均化温度分布范围从910—1250℃，峰值明显，计算的均化温度为Tz=(1081.4±177.9)℃，但还存在有高于1250℃的均化温度峰。包裹体均化法测试结果说明浮岩中斜长石的形成过程至少有两个阶段：第一阶段的岩浆温度在1200—1300℃左右，在此温度下形成的是An值较高的基性斜长石，同时结晶的还有辉石等矿物，斜长石结晶第二个阶段时的熔浆温度在1100℃以下，这一阶段持续的时间长，跨越的温度范围大，应是岩浆在近地表和岩浆喷出过程中的岩浆快速冷却期，同时伴随有矿物大规模晶出。(3)包裹体中的气相部分均聚合成圆形或近圆形，说明温度下降速度较快。斑晶斜长石中部分包裹体与基质玻璃中包裹体的形成温度是连续变化的，这一事实应该与冲绳海槽特殊的地质条件有关     

A Moored Underwater Energy Conservation System for Profiling Measurement

There is a need to obtain the hydrologic data including ocean current,wave,temperature and so on in the South China Sea.A new profiling instrument which does not suffer from the damage due to nature forces or incidents caused by passing ships,is under development to acquire data from this area.This device is based on a taut single point mid-water mooring system.It incorporates a small,instrumented vertically profiling float attached via an electromechanical cable to a winch integral with the main subsurface flotation.On a pre-set schedule,the instrument float with sensors is winched up to the surface if there is no ship passing by,which is defined by an on-board miniature sonar.And it can be immediately winched down to a certain depth if the sonar sensor finds something is coming.Since,because of logistics,the area can only be visited once for a long time and a minimum of 10 times per day profiles are desired,energy demands are severe.To respond to these concerns,the system has been designed to conserve a substantial portion of the potential energy lost during the ascent phase of each profile and subsequently use this energy to pull the instrument down.Compared with the previous single-point layered measuring mode,it is advanced and economica1.At last the paper introduces the test in the South China Sea.     

深海系泊法向承力锚模型实验系统

法向承力锚是一种新型的拖曳嵌入式系泊基础.这种锚的工程应用仅有10 a时间.国内在此项技术上尚属空白.通过实验系统的设计,介绍了针对这种新型拖曳锚展开模型实验研究的实验平台.利用一些新型传感器和巧妙的机件设计,不仅实现了实验量测方法的创新,而且达到了经济实用的目的.实验结果也验证了整个系统设计的可靠性.     

ADCP资料处理中的船速计算

船载ADCP具有走航测流的特点,弥补了传统测流仪器只有停船才能观测的不足。它可以同时观测多层海流数据,获取连续性资料。ADCP测得流速是海水相对于船体的速度,在正常观测条件下,船速远大于海水流速,因而船速计算是ADCP资料处理的关键。本文对不同的船速计算方法进行了比较,对使用参考层法计算船速的原理、特点和效果进行了论述。     

底栖生物生产力现场测试系统(BCSPM)的建立及其初步实验结果

为对生态系统的健康评估及底栖生物资源的开发利用提供技术支撑,在胶州湾筏式养殖水域,建立了底栖生物生产力现场测试系统(BCSPM),并在光照和黑暗条件下测定了沉积物海水界面溶解氧随时间的变化、计算了氧通量、估算了底栖总初级生产力和群落呼吸。在光照较强的中午时刻测定的群落总生产力为20．76mgCm^-2h^-1;养殖水域沉积物中的群落呼吸要高于邻近水域。BCSPM整体运转良好,初步结果为系统的改进和进一步实验提供了依据。     

渤海的平均余环流

利用72个渤海石油平台、站点测流资料,阐明了渤海的平均余环流特征,并用已有的数值计算结果阐明了其形成机制。观测表明在黄河三角洲近海存在一支北-东北向的流动,可抵达秦皇岛附近水域,数值计算表明该支流动主要是潮生的;在辽东湾北部存在一顺时针向的涡旋运动,在冬半年该涡旋是风生的;在渤海湾北部存在潮生的逆时针向的余环流。     

无人水下智能海洋测绘装备的机遇与挑战

针对海洋测绘面临的问题,分析了无人时代海洋测绘技术的发展机遇,提出了无人水下智能海洋测绘的新模式,讨论了无人水下智能海洋测绘的技术体系和无人水下智能海洋测绘装备的关键技术,以及无人水下智能海洋测绘的装备产业链,展望了无人水下智能海洋测绘装备的发展趋势及应用前景。