Early Estimation of Seismic Hazard for Strong Earthquakes in Taiwan

A shakemap system providing rapid estimates of strong ground shaking could be useful for emergency response providers in a damaging earthquake. A hybrid procedure, which combines site-dependent ground motion prediction models and the limited observations of the Real-Time Digital stream output system (RTD system operated by Central Weather Bureau, CWB), was set up to provide a high-resolution shakemap in a near-real-time manner after damaging earthquakes in Taiwan. One of the main factors that affect the result of ground motion prediction analysis is the existence of site effects. The purpose of this paper is to investigate the local site effects and their influence in the ground shaking and then establish an early estimation procedure of potential hazard for damaging earthquakes. Based on the attenuation law, the site effects of each TSMIP station are discussed in terms of a bias function that is site and intensity-level dependent function. The standard deviation of the site-dependent ground motion prediction model can be significantly reduced. The nonlinear behavior of ground soil is automatically taken into account in the intensity-level dependent bias function. Both the PGA and the spectral acceleration are studied in this study. Based on the RTD data, event correctors are calculated and applied to precisely estimate the shakemap of damaging earthquakes for emergency response.     

青藏高原中部的东西向扩张构造运动

系统分析了1933~2003年间青藏高原及其周缘发生的745个中、强地震的震源机制解,研究了高原地壳构造运动及其动力学特征。结果表明,大量正断层型地震集中发生在青藏高原中部海拔4000m以上的地区,其中许多地震是纯正断层型地震。震源机制结果显示,该区正断层型地震的断层走向多为南北方向,断层位错矢量的水平分量均位于近东西方向,这表明青藏高原高海拔地区存在着近东西方向的扩张构造运动。地震震源应力场的研究结果表明,在高原中部高海拔地区,E-W向或WNW-ESE向的水平扩张作用控制着该区的地壳应力场。青藏高原高海拔地区近东西方向的扩张构造运动是该区引张应力场的作用结果,其动力学原因可能与持续隆升的高原自重增大引起的重力崩塌及其周边区域构造应力状况有关。而青藏高原周缘地区,除了东部边缘外,南部的喜马拉雅山前沿以及青藏高原的北部、西部边缘所发生的绝大部分地震都是逆断层型或走滑逆断层型地震。在青藏高原周缘地区,北东或者北北东方向水平挤压的构造应力场为优势应力场。在中国西部的大范围内,主压应力P轴水平分量位于NE-SW方向,形成了一个广域的NE-SW方向的挤压应力场。青藏高原及其周缘应力场特征表明,印度板块的北上运动以及它与欧亚板块之间的碰撞所形成的挤压应力场是高原强烈隆起的直接原因。在青藏高原中南部形成了近东西向引张应力场为主的区域,并以东西向扩张构造运动部分释放其应力积累。研究高原高海拔地区的引张应力场和近东西向扩张构造运动的特征,对于认识青藏高原强烈隆起的地球动力学过程与机制,有着重要的理论意义。     

CCSD在线流体监测捕获的气体地球化学异常与2004年9．3级苏门答腊地震可能的超远程关系

中国大陆科学钻探工程在线流体地球化学监测在2004年12月10至2005年1月10日之间捕获到一段重要的气体地球化学异常。该异常从2004年12月24日晚上11点半开始到12月29日晚上7点半结束,其中在12月26日早上7点半到29日晚7点半这段异常非常特殊,表现出流体地球化学的剧烈变化。具体表现为流体组分从基本上不含Ar、He及N2跳跃到富含Ar、但亏损He和N2。该异常发生在2004年9.3级苏门答腊地震前1个半小时。由于CCSD现场离苏门答腊地震震中距离大于4170公里,大于该地震破裂长度1200公理的3倍,该地震在CCSD现场产生的静态应力变化微乎其微,不足以导致CCSD现场深部岩石或封闭破裂的岩石物理性质剧烈变化,因而可以排除静态激发效应的作用。在我国的云南和广东等地所观测到的地震异常和地下水位变化等表明2004年苏门答腊地震的动态激发效应主要沿东北方向,这和大地震的动态激发具有方向性一致。而CCSD现场就位于该方向上。我们推测2004年苏门答腊地震所产生的面波在CCSD现场激发的动态效应,导致库仑型失稳,增进深部岩石或破裂带的渗透率,释放富含Ar但亏损He和N2的流体,产生CCSD所观测到的气体异常。     

地震作用下的灰坝液化特征及其动力稳定性分析--以安阳电厂为例

根据安阳电厂灰坝岩土工程性质及其动力学特性,建立了适合灰坝工程的动力分析模型并采用有限元法进行了动力分析.在此基础上,在不同工况条件下对灰坝进行了抗液化安全评价及抗震稳定性分析.研究表明,在不设碎石桩、无排渗体条件下,粉煤灰子坝的抗液化安全系数Ks＜1.25,将发生液化;在设碎石桩、有排渗体条件下,粉煤灰子坝的抗液化安全系数明显提高,Ks≥1.25,不会发生液化.抗震稳定性分析表明,在上述两种工况条件下灰坝是稳定的.     

白云鄂博碳酸岩型REE-Nb-Fe矿床——一个罕见的中元古代破火山机构成岩成矿实例

白云鄂博碳酸岩型REE-Nb-Fe矿床是世界上最大的稀土矿床。稀土矿石产于整个白云石碳酸岩体和部分脉状碳酸岩中。对比世界上20余个火成碳酸岩地区的特征后发现,白云鄂博地区完全具备国外火成碳酸岩区的地质特征。在岩石、矿石组合上,本区也发育一套碳酸岩+超基性岩+碱性基性岩(含基性熔岩)+碱性岩+稀土矿石+铁矿石组合;在矿物组合上,以白云石为主,方解石次之,伴生一套碱性闪石、长石、霓石、磷灰石、萤石、磁铁矿、稀土矿物组合;在全岩化学成分、微量元素、稀土元素和Sr、Nd、Pb、C、O同位素上,这些岩石具有一定的亲缘关系,有着共同的来源;在岩体的形态与岩石组构上,它们以岩席、岩筒和脉岩的形式出现,并发育有强烈的熔离作用与流动构造;在区域构造上,发育隐伏穹窿构造、岩筒构造和巨型断裂汇聚构造。综合分析上述特征表明:白云鄂博地区具有中元古代破火山机构的痕迹,赋矿白云石碳酸岩体则是顺层侵入的火成碳酸岩体,东矿、主矿可能是一个火山颈构造控矿,而赋矿白云石碳酸岩体西南侧的苏木图矿床则是隐伏岩筒构造控矿。     

Tests on low‐ductility RC frames under high‐ and low‐frequency excitations

The response of low‐ductility reinforced concrete (RC) frames, designed typically for a non‐seismic region, subjected to two frequencies of base excitations is studied. Five half‐scaled, two‐bay, two‐storey, RC frames, each approximately 5 m wide by 3.3 m high, were subjected to both horizontal and/or vertical base excitations with a frequency of 40 Hz as well as a lower frequency of about 4 Hz (close to the fundamental frequency) using a shake table. The imposed acceleration amplitude ranged from 0.2 to 1.2g. The test results showed that the response characteristics of the structures differed under high‐ and low‐frequency excitations. The frames were able to sustain high‐frequency excitations without damage but were inadequate for low‐frequency excitations, even though the frames exhibited some ductility. Linear‐elastic time‐history analysis can predict reasonably well the structural response under high‐frequency excitations. As the frames were not designed for seismic loads, the reinforcement detailing may not have been adequate, based on the crack pattern observed. The effect of vertical excitation can cause significant additional forces in the columns and moment reversals in the beams. The ‘strong‐column, weak‐beam’ approach for lateral load RC frame design is supported by experimental observations. Copyright © 2001 John Wiley & Sons, Ltd.     

Optimal design of passive energy dissipation systems based on H∞ and H2 performances

Passive energy dissipation devices (EDDs), such as viscous dampers, viscoelastic dampers, etc., have been used to effectively reduce the dynamic response of civil infrastructures, such as buildings and bridges, subject to earthquakes and strong winds. The design of these passive energy dissipation devices (EDDs) involves the determination of the optimal locations and the corresponding capacities. In this paper, we present two optimal design methodologies for passive EDDs based on active control theories, including H_∞ and H₂ performances, respectively. The optimal design methodologies presented are capable of determining the optimal locations and the corresponding capacities of EDDs. Emphasis is placed on the application of linear matrix inequality (LMI) for the effective design of passive EDDs using the popular MATLAB toolboxes. One important advantage of the proposed approaches is that the computation of the structural response is not needed in the design process. The proposed optimal design methodologies have been applied to: (i) a 10‐storey building and a 24‐storey building both subject to earthquake excitations, and (ii) a 76‐storey wind‐excited benchmark building, to demonstrate the advantages of the proposed design methodologies over the conventional equal capacity design. Copyright © 2002 John Wiley & Sons, Ltd.     

Seismic response of self‐centring hysteretic SDOF systems

The seismic response of single‐degree‐of‐freedom (SDOF) systems incorporating flag‐shaped hysteretic structural behaviour, with self‐centring capability, is investigated numerically. For a SDOF system with a given initial period and strength level, the flag‐shaped hysteretic behaviour is fully defined by a post‐yielding stiffness parameter and an energy‐dissipation parameter. A comprehensive parametric study was conducted to determine the influence of these parameters on SDOF structural response, in terms of displacement ductility, absolute acceleration and absorbed energy. This parametric study was conducted using an ensemble of 20 historical earthquake records corresponding to ordinary ground motions having a probability of exceedence of 10% in 50 years, in California. The responses of the flag‐shaped hysteretic SDOF systems are compared against the responses of similar bilinear elasto‐plastic hysteretic SDOF systems. In this study the elasto‐plastic hysteretic SDOF systems are assigned parameters representative of steel moment resisting frames (MRFs) with post‐Northridge welded beam‐to‐column connections. In turn, the flag‐shaped hysteretic SDOF systems are representative of steel MRFs with newly proposed post‐tensioned energy‐dissipating connections. Building structures with initial periods ranging from 0.1 to 2.0s and having various strength levels are considered. It is shown that a flag‐shaped hysteretic SDOF system of equal or lesser strength can always be found to match or better the response of an elasto‐plastic hysteretic SDOF system in terms of displacement ductility and without incurring any residual drift from the seismic event. Copyright © 2002 John Wiley & Sons, Ltd.     

Numerical evaluation of the damping‐solvent extraction method in the frequency domain

The damping‐solvent extraction method for the analysis of unbounded visco‐elastic media is evaluated numerically in the frequency domain in order to investigate the influence of the computational parameters—domain size, amount of artificial damping, and mesh density—on the accuracy of results. An analytical estimate of this influence is presented, and specific questions regarding the influence of the parameters on the results are answered using the analytical estimate and numerical results for two classical problems: the rigid strip and rigid disc footings on a visco‐elastic half‐space with constant hysteretic material damping. As the domain size is increased, the results become more accurate only at lower frequencies, but are essentially unaffected at higher frequencies. Choosing the domain size to ensure that the static stiffness is computed accurately leads to an unnecessarily large domain for analysis at higher frequencies. The results improve by increasing artificial damping but at a slower rate as the total (material plus artificial) damping ratio ζ_t gets closer to 0.866. However, the results do not deteriorate significantly for the larger amounts of artificial damping, suggesting that ζ_t≈0.6 is appropriate; a larger value is not likely to influence the accuracy of results. Presented results do not support the earlier suggestion that similar accuracy can be achieved by a large bounded domain with small damping or by a small domain with larger damping. Copyright © 2002 John Wiley & Sons, Ltd.     

Multi‐objective optimal design of FLC driven hybrid mass damper for seismically excited structures

Structural vibration control using active or passive control strategy is a viable technology for enhancing structural functionality and safety against natural hazards such as strong earthquakes and high wind gusts. Both the active and passive control systems have their limitations. The passive control system has limited capability to control the structural response whereas the active control system depends on external power. The power requirement for active control of civil engineering structures is usually quite high. Thus, a hybrid control system is a viable solution to alleviate some of the limitations. In this paper a multi‐objective optimal design of a hybrid control system for seismically excited building structures has been proposed. A tuned mass damper (TMD) and an active mass driver (AMD) have been used as the passive and active control components of the hybrid control system, respectively. A fuzzy logic controller (FLC) has been used to drive the AMD as the FLC has inherent robustness and ability to handle the non‐linearities and uncertainties. The genetic algorithm has been used for the optimization of the control system. Peak acceleration and displacement responses non‐dimensionalized with respect to the uncontrolled peak acceleration and displacement responses, respectively, have been used as the two objectives of the multi‐objective optimization problem. The proposed design approach for an optimum hybrid mass damper (HMD) system, driven by FLC has been demonstrated with the help of a numerical example. It is shown that the optimum values of the design parameters of the hybrid control system can be determined without specifying the modes to be controlled. The proposed FLC driven HMD has been found to be very effective for vibration control of seismically excited buildings in comparison with the available results for the same example structure but with a different optimal absorber. Copyright © 2002 John Wiley & Sons, Ltd.