某双向混凝土立交桥顶推法施工控制测量

文中所选立交桥为双向三车道桥梁,单幅为3跨105 m的箱型连续梁,重量3 400 t,横跨铁路线。对于跨铁路的桥梁建设,顶推法施工可最大限度地减少对交通的影响。桥梁重量大,所须牵引力约280 t,施工过程中对桥墩及其他建筑物产生的变形较大,施工前模拟施工状态,设计控制测量监控的基本方案,利用控制测量方法,对施工状态实时监测,预测变形及偏位、纠偏,使施工状态最大限度地接近理想状态。顶推到位后,轴向偏位满足1 cm的限差,桥墩变形基本满足施工规范的要求,最终顺利完成顶推过程。     

Compression limit state of HVAC submarine cables

An industry accepted standard does not currently exist for determination of compression limits in a subsea cable. This has resulted in most manufacturers specifying that subsea cables are not permitted to be axially loaded in compression.Additionally industry guidance does not exist regarding the consequences of inducing compression forces within subsea cables and the resulting effect on cable integrity. Industry recommended practice and guidance also does not have any information regarding experimental test arrangements to determine allowable compression levels within a subsea cable. This lack of modelling/testing guidance along with manufacturer recommendations of zero compressive loads within subsea cables results in overly conservative and restrictive design parameters for subsea cable installation and use.Due to the complex interaction within a subsea cable structure, such as contact interaction and friction between cable strands, theoretical modelling has been unable to provide reliable stress predictions and therefore an experimental testing regime is required if compression limits within the cable are to be appropriately determined. This paper describes combined axial and bending test arrangements that can be used as a guideline for determination of allowable compression limits for subsea cables.     

全珊瑚骨料海水混凝土力学性能试验研究

为了探讨全珊瑚骨料海水混凝土的基本力学性能,并比较其与普通混凝土和轻集料混凝土的差异,通过实验系统测定了珊瑚混凝土的基本力学性能,建立了其轴心抗压强度(f_(c,m))、劈裂抗拉强度(f_(sp,m))、抗折强度(f_(t,m))与立方体抗压强度(f_(cu,m))之间的线性关系与计算公式。结果表明:在强度等级C20~C50的范围内,珊瑚混凝土的f_(c,m)和f_(sp,m)分别比普通混凝土的f_(c,m)和f_(sp,m)高出10%~48%和9%~33%,随着强度等级的提高,两种混凝土之间的差距在减小。珊瑚混凝土的f_(t,m)与普通混凝土的ft,m之间的差异规律与强度等级有关,较低强度等级的C30珊瑚混凝土ft,m比普通混凝土的f_(t,m)要高4%,而较高强度等级的C55珊瑚混凝土f_(t,m)比普通混凝土的f_(t,m)低13%。较高强度等级的C50珊瑚混凝土f_(c,m)、f_(sp,m)和f_(t,m)分别比页岩陶粒轻集料混凝土的f_(c,m)、f_(sp,m)和f_(t,m)低11%、0.9%和4%。     

四川盆地：周缘活动主控下形成的叠合盆地

四川盆地位于扬子板块西缘和青藏高原东缘,地震勘探资料等揭示盆地前寒武纪基底保存完整的古俯冲带和地堑-地垒结构,说明盆地基底后期构造活动非常稳定;显生宙以来经历晚震旦世-石炭纪、二叠纪-中三叠世两幕克拉通边缘强拉张-强挤压,而克拉通内弱拉张-弱挤压的构造演化过程,体现出盆地内部稳定性结构沉积演化特征。克拉通内弱拉张初期以海相碳酸盐岩大面积稳定沉积（即震旦系灯影组和二叠系栖霞-茅口组）和随后的风化壳岩溶作用（即桐湾期、东吴期等不整合面）为特征,弱拉张期以拉张槽（如：绵阳-长宁拉张槽和开江-梁平拉张槽等）的形成为典型特征;弱挤压则以古隆起（如：加里东期乐山-龙女寺古隆起、印支期泸州古隆起等）的发育为典型特征。四川盆地晚三叠世后的前陆盆地演化阶段受控于其周缘造山带逆冲推覆构造活动,是现今地貌和构造盆地的主要建造期,形成了四川盆地周缘突变（线型）和渐变（弥散型）两种盆山结构。盆地西边界（龙门山）和北边界（米仓山-大巴山）即是线型突变边界,也是扬子地块（板块）的边界,边界几何形状和扬子板块刚性特征对盆山系统结构-构造特征等有较大的控制作用;四川盆地的东边界（齐岳山-大娄山）和西南边界（大凉山）即是渐变弥散型边界,同时也是板（陆）块内部的边界,它们受控于邻区（盆外）的构造变形和盆内沉积盖层中滑脱层的分布特征。受控于盆地（克拉通）周缘活动,四川盆地垂向上前寒武纪基底与盖层、盖层内早期和晚期构造具解耦特征。基底与盖层构造的解耦有利于盆地内部前寒武纪基底结构构造的保存和盖层内大型隆-坳结构的形成演化;盖层内早期和晚期构造的解耦有利于早期构造免遭后期破环,对深层油气藏的保存意义重大。总之,四川盆地可能是具独特形成过程和特征的叠合盆地新类型,其突出特征表现为周缘活动、内部稳定及早期和晚期构造解耦。     

内含裂隙角的恐龙化石轴向受压数值试验及裂纹扩展机理研究

面临众多古生物化石遭受风化破坏的现实,恐龙化石保护是一项世界性难题。化石的风化原因多种多样,其中化石内部裂隙是导致恐龙化石风化、破坏的重要因素。该文以岩石断裂力学为理论依据,模拟分析内含裂隙的恐龙化石在压力作用下的破坏情况。通过数值模拟的方法,进行了内含裂隙恐龙化石数值压缩试验,并对内含裂隙的恐龙化石裂纹扩展机理进行了研究。研究结果表明,随着裂隙角度增大,开裂角逐渐减小,裂隙处特别是两端应力集中,其他部位应力较低、分布均匀;裂纹扩展是从裂纹尖端起裂,最终裂纹扩展到边缘。此研究结果为揭示恐龙化石风化机理和开展保护提供了基础参考资料。     

Effects of installation on the cyclic axial behaviour of suction buckets in sandy soils

Suction buckets differ with their easy and cost-efficient installation technique from other foundation types for offshore wind turbines. For successful completion of their installation process, suction is essential, but the imposed seepage leads to the changes in states of the soil in and around the bucket. Especially, a loosening of soil inside the bucket affects the load carrying behaviour of bucket subjected to repetitive loading resulting from environmental conditions. In this study, the behaviour of buckets under cyclic axial compressive loads with considering a possible loosening and related changes in permeability of soil inside the bucket is investigated numerically. In the framework of finite element analysis, a fully coupled two-phase model and a hypoplastic constitutive model are used to describe the saturated sandy soil behaviour under repetitive loading. The porosity-permeability variation is taken into account by Kozeny–Carman relationship. Special attention is dedicated to load carrying behaviour of bucket top plate, inner and outer skirt as well as base and their changes resulting from a loosening of soil inside the bucket with variable aspect ratio. For this purpose, cyclic axial compressive loads which cause an attenuation and progressive failure of soil-bucket system response are considered. The main findings on the changes in load carrying behaviour of bucket are presented and discussed.     

Numerical Simulation on Flow Past Two Side-by-Side Inclined Circular Cylinders at Low Reynolds Number

A series of three-dimensional numerical simulations is carried out to investigate the effect of inclined angle on flow behavior behind two side-by-side inclined cylinders at low Reynolds number Re=100 and small spacing ratio T/D=1.5 (T is the center-to-center distance between two side-by-side cylinders, D is the diameter of cylinder). The instantaneous and time-averaged flow fields, force coefficients and Strouhal numbers are analyzed. Special attention is focused on the axial flow characteristics with variation of the inclined angle. The results show that the inclined angle has a significant effect on the gap flow behaviors behind two inclined cylinders. The vortex shedding behind two cylinders is suppressed with the increase of the inclined angle as well as the flip-flop gap flow. Moreover, the mean drag coefficient, root-mean-square lift coefficient and Strouhal numbers decrease monotonously with the increase of the inclined angle, which follows the independent principle at small inclined angles.     

轴压作用下双金属复合管组合作用与承载力分析

为探究轴压作用下双金属复合海底管道的组合作用与承载性能,对双金属复合海底管道进行了试验研究和理论分析。开展了不锈钢衬管材料性能试验,对比了国际主流不锈钢本构关系模型和试验结果。利用ABAQUS建立了精细化的双金属复合管道轴压试验有限元模型,系统研究了关键参数如复合工艺产生的环向复合应力、钢管初始缺陷幅值等对双金属复合管在轴压作用下力学性能的影响规律。通过对比已有轴压双金属复合管道试验结果,验证有限元模型。基于验证的有限元模型,对轴压作用下双金属复合管道的组合作用以及径厚比和材料强度对承载力的影响进行了分析。结果表明双金属复合管道的轴压极限承载力主要取决于基管的截面屈服荷载,并随着管径和材料强度的提高而增大。并依据分析结果对双金属复合海底管道的设计提出建议。     

轴压比对中等高度LC结构剪力墙抗震性能的影响

轻骨料混凝土(L ight-we ight concrete,简称LC)剪力墙的轴压比是剪力墙抗震设计时一个重要的控制因素,直接关系到其延性性能。为使设计规程具有足够的理论依据,本文通过对六榀轻骨料混凝土剪力墙试件的试验,研究了在低周反复荷载作用下,着重考虑不同轴压比对中等高度有边框剪力墙的破坏形态和变形性能的影响效应,对其滞回特性进行分析,计算了各剪力墙的刚度退化率与延性系数,并将无竖缝剪力墙与带竖缝剪力墙的抗震性能进行了对比。     

新型珊瑚海水混凝土力学性能试验研究

为了解决全珊瑚海水混凝土(coral aggregate seawater concrete,简称CASC)的脆性问题,采用碱式硫酸镁水泥(basic magnesium sulfate cement,简称BMSC)为胶凝材料和剑麻纤维为增韧材料制备了一种新型全珊瑚海水混凝土(NCASC),系统测定了基本力学性能,并与普通硅酸盐水泥制备的CASC、碱式硫酸镁水泥砂石混凝土(basic magnesium sulfate cement concrete,简称BMSCC)、普通砂石混凝土(ordinary portland cement concrete,简称OPC)以及普通轻骨料混凝土(lightweight aggregate concrete,简称LAC)的力学性能进行对比。结果表明:立方体抗压强度(f_(cu),m)在15~35 MPa范围内的NCASC的轴心抗压强度(f_c,m)、劈裂抗拉强度(f_(sp),m)与f_(cu),m之间具有较显著的线性关系;对于f_(cu),m为15~35 MPa的混凝土,相同强度NCASC的f_c,m高于OPC、LAC及BMSCC,其f_c,m与f_(cu),m比值最大,大致在0.85~0.96之间,NCASC的f_(sp),m比OPC和LAC高,但比BMSCC低,且随着强度的提高,OPC与NCASC的f_(sp),m间的差距在增大,而LAC和BMSCC与NCASC的f_(sp),m间的差距在缩小;在强度等级C15~C55的范围中,NCASC和CASC的f_(sp),m、f_c,m与f_(cu),m之间的关系基本可以采用相同的线性回归方程来描述,利用这两个回归线性方程得到对应于标准强度等级的CASC和NCASC的f_(sp),m和f_c,m数据,为CASC力学性能研究与结构设计提供参考依据。