Estimation of fundamental periods of shear‐wall dominant building structures

Shear‐wall dominant multistorey reinforced concrete structures, constructed by using a special tunnel form technique are commonly built in countries facing a substantial seismic risk, such as Chile, Japan, Italy and Turkey. In spite of their high resistance to earthquake excitations, current seismic code provisions including the Uniform Building Code (International Conference of Building Officials, Whittier, CA, 1997) and the Turkish Seismic Code (Specification for Structures to be Built in Disaster Areas, Ankara, Turkey, 1998) present limited information for their design criteria. In this study, consistency of equations in those seismic codes related to their dynamic properties are investigated and it is observed that the given empirical equations for prediction of fundamental periods of this specific type of structures yield inaccurate results. For that reason, a total of 80 different building configurations were analysed by using three‐dimensional finite‐element modelling and a set of new empirical equations was proposed. The results of the analyses demonstrate that given formulas including new parameters provide accurate predictions for the broad range of different architectural configurations, roof heights and shear‐wall distributions, and may be used as an efficient tool for the implicit design of these structures. Copyright © 2003 John Wiley & Sons, Ltd.     

Aseismic negative dislocation model and deformation analysis of crustal horizontal movement during 1999——2001 in the northeast margin of Qinghai-Xizang block

Through numerical simulation for GPS data, aseism/c negative dislocation model for crustal horizontal movement during 1999-2001 in the northeast margin of Qinghai-Xizang block is presented, combined with the spatial distri-bution of apparent strain field in this area, the characteristics of motion and deformation of active blocks and their boundary faults, together with the place and intensity of strain accumulation are analyzed. It is shown that: a) 9 active blocks appeared totally clockwise motion from eastward by north to eastward by south. Obvious sinistral strike-slip and NE-NEE relative compressive motion between the blocks separated by Qilianshan-Haiyuan fault zone was discovered; b) 20 fault segments (most of them showed compression) locked the relative motion between blocks to varying degrees, among the total, the mid-east segment of Qilianshan fault (containing the place where it meets Riyueshan-Lajishan fault) and the place where it meets Haiyuan fault and Zhuanglanghe fault, more favored accumulation of strain. Moreover, the region where Riyueshan-Lajishan fault meets north boundary of Qaidam block may have strain accumulation to some degree, c) Obtained magnitude of block velocities and locking of their boundaries were less than relevant results for observation in the period of 1993-1999.     

Movement and strain conditions of active blocks in the Chinese mainland

The definition of active block is given from the angles of crustal deformation and strain. The movement and strain parameters of active blocks are estimated according to the unified velocity field composed of the velocities at 1598 GPS stations obtained from GPS measurements carried out in the past years in the Chinese mainland and the surrounding areas. The movement and strain conditions of the blocks are analyzed. The active blocks in the Chinese mainland have a consistent E-trending movement component, but its N and S components are not consistent. The blocks in the western part have a consistent N-trending movement and the blocks in the eastern part have a consistent S-trending movement. In the area to the east of 90°E, that is the area from Himalayas block towards NE, the movement direction of the blocks rotates clockwisely and the movement rates of the blocks are different. Generally, the movement rate is large in the west and south and small in the east and north with a difference of 3 to 4 times between the rates in the west and east. The distributions of principal compressive strain directions of the blocks are also different. The principal strain of the blocks located to the west of 90oE is basically in the SN direction, the principal compressive strain of the blocks in the northeastern part of Qingzang plateau is roughly in the NE direction and the direction of principal compressive strain of the blocks in the southeastern part of Qingzang plateau rounds clockwisely the east end of Himalayas structure. In addition, the principal strain and shear strain rates of the blocks are also different. The Himalayas and Tianshan blocks have the largest principal compressive strain and the maximum shear strain rate. Then, Lhasa, Qiangtang, Southwest Yunnan (SW Yunnan), Qilian and Sichuan-Yunan (Chuan-Dian) blocks followed. The strain rate of the blocks in the eastern part is smaller. The estimation based on the stain condition indicates that Himalayas block is still the area with the most intensive tectonic activity and it shortens in the NS direction at the rate of 15.2±1.5 mm/a. Tianshan block ranks the second and it shortens in the NS direction at the rate of 10.1±0.9 mm/a. At present, the two blocks are still uprising. It can be seen from superficial strain that the Chinese mainland is predominated by superficial expansion. Almost the total area in the eastern part of the Chinese mainland is expanded, while in the western part, the superficial compression and expansion are alternatively distributed from the south to the north. In the Chinese mainland, most EW-trending or proximate EW-trending faults have the left-lateral or left-lateral strike-slip relative movements along both sides, and most NS-trending faults have the right-lateral or right-lateral strike-slip relative movements along both sides. According to the data from GPS measurements the left-lateral strike-slip rate is 4.8±1.3 mm/a in the central part of Altun fault and 9.8±2.2 mm/a on Xianshuihe fault. The movement of the fault along the block boundary has provided the condition for block movement, so the movements of the block and its boundary are consistent, but the movement levels of the blocks are different. The statistic results indicate that the relative movement between most blocks is quite significant, which proves that active blocks exist. Himalayas, Tianshan, Qiangtang and SW Yunnan blocks have the most intensive movement; China-Mongolia, China-Korea (China-Korea), Alxa and South China blocks are rather stable. The mutual action of India, Pacific and Philippine Sea plates versus Eurasia plate is the principal driving force to the block movement in the Chinese mainland. Under the NNE-trending intensive press from India plate, the crustal matter of Qingzang plateau moves to the NNE and NE directions, then is hindered by the blocks located in the northern, northeastern and eastern parts. The crustal matter moves towards the Indian Ocean by the southeastern part of the plateau.     

韧性剪切带的变形变质与同构造熔融作用——以中祁连地块宝库河韧性走滑剪切带为例

宝库河韧性剪切带是发育在中祁连地块北缘上的一条向北陡倾,走向近东西,宽约6 km的右行平移型韧性剪切带.剪切带内岩石原岩为泥质岩、基性岩和花岗岩,变质程度达角闪岩相,变形变质温度在685～763±46℃之间,压力在0.62～0.83±0.13 GPa范围内.其内长英质条带非常发育,规模变化较大,分布局部相对集中且受剪切带控制,走向与剪切带一致,平行于叶理,孤立无根,并在后期递进变形过程中发生不同程度的糜棱岩化、布丁化和褶皱,主要成分为长石和石英,明显不同于韧性剪切前或后侵入的花岗岩脉或岩体.长英质条带特征、REE配分模式及剪切带内岩石的变形变质温度说明剪切带内发育的长英质条带与基体是同源的,是在剪切应变过程中剪切热使围岩内部分物质发生动态熔融形成的,是同构造熔融作用的产物.     

Simulation and measurement of surface shear stress over isolated and closely spaced transverse dunes in a wind tunnel

Topographic interactions generate multidirectional and unsteady air?ow that limits the application of velocity pro?le approaches for estimating sediment transport over dunes. Results are presented from a series of wind tunnel simulations using Irwin‐type surface‐mounted pressure sensors to measure shear stress variability directly at the surface over both isolated and closely spaced sharp‐crested model dunes. Findings complement existing theories on secondary air?ow effects on stoss transport dynamics and provide new information on the in?uence of lee‐side air?ow patterns on dune morphodynamics. For all speeds investigated, turbulent unsteadiness at the dune toe indicates a greater, more variable surface shear, despite a signi?cant drop in time‐averaged measurements of streamwise shear stress at this location. This effect is believed suf?cient to inhibit sediment deposition at the toe and may be responsible for documented intermittency in sand transport in the toe region. On the stoss slope, streamline compression and ?ow acceleration cause an increase in ?ow steadiness and shear stress to a maximum at the crest that is double that at the toe of the isolated dune and 60–70 per cent greater than at ?ow reattachment on the lower stoss of closely spaced dunes. Streamwise ?ow accelerations, rather than turbulence, have greater in?uence on stress generation on the stoss and this effect increases with stoss slope distance and with incident wind speed. Reversed ?ow within the separation cell generates signi?cant surface shear (30–40 per cent of maximum values) for both spacings. This supports ?eld studies that suggest reversed ?ow is competent enough to return sediment to the dune directly or in a de?ected direction. High variability in shear at reattachment indicates impact of a turbulent shear layer that, despite low values of time‐averaged streamwise stress in this region, would inhibit sediment accumulation. Downwind of reattachment, shear stress and ?ow steadiness increase within 6 h (h = dune height) of reattachment and approach upwind values by 25 h. A distance of at least 30 h is suggested for full boundary layer recovery, which is comparable to ?uvial estimates. The Irwin sensor used in this study provides a reliable means to measure skin friction force responsible for sand transport and its robust, simple, and cost‐effective design shows promise for validating these ?ndings in natural dune settings. Copyright © 2003 John Wiley & Sons, Ltd.     

Jurassic Dextral and Cretaceous Sinistral Movements Along the Hida Marginal Belt

The Hida marginal belt (HMB), which consists of various kinds of fault-bound blocks, is located between the continental massif of the Hida belt and the Mesozoic accretionary complex of the Mino belt in Central Japan. Detailed field investigation reveals that the HMB had grown through the two different movements, i.e., Jurassic dextral and Cretaceous sinistral movements. The Jurassic dextral ductile shear zones run in the southern marginal part of the Hida belt and the northern part of the HMB, whereas the Cretaceous sinistral cataclastic shear zones occur in the southern part of the HMB and the northern marginal part of the Mino belt. Geologic map and field evidence seem to suggest that the Jurassic dextral movement form the fault-bound blocks of the HMB to form the basic structure of the Hida marginal belt, i.e., formation of the ‘proto-HMB.’ Following the dextral movement, the sinistral one restructured the ‘proto-HMB’ to complete the present feature of the Hida marginal belt. The Cretaceous sinistral movement might result in the sinistral collision between the proto-HMB and the Mino belt.     

APPLICATION OF SOME MECHANICAL CONCEPTS TO STRUCTURAL GEOLOGY

This paper discusses some mechanical concepts that have been largely applied to structural geology and tectonics, and addresses the problems and misunderstandings in use of these mechanical terms. The purpose is to stimulate the interests for structural geologists in using the mechanical principles and methods correctly to solve the geodynamic problems.     

Contrasting metamorphic evolution of metasedimentary rocks from the Çine and Selimiye nappes in the Anatolide belt, western Turkey

Abstract P–T conditions, mineral isograds, the relation of the latter to foliation planes and kinematic indicators are used to elucidate the tectonic nature and evolution of a shear zone in an orogen exhumed from mid‐crustal depths in western Turkey. Furthermore, we discuss whether simple monometamorphic fabrics of rock units from different nappes result from one single orogeny or are related to different orogenies. Metasedimentary rocks from the Çine and Selimiye nappes at the southern rim of the Anatolide belt of western Turkey record different metamorphic evolutions. The Eocene Selimiye shear zone separates both nappes. Metasedimentary rocks from the Çine nappe underneath the Selimiye shear zone record maximum P–T conditions of about 7 kbar and >550 °C. Metasedimentary rocks from the overlying Selimiye nappe have maximum P–T conditions of 4 kbar and c. 525 °C near the base of the nappe. Kinematic indicators in both nappes are related to movement on the Selimiye shear zone and consistently show a top‐S shear sense. Metamorphic grade in the Selimiye nappe decreases structurally upwards as indicated by mineral isograds defining the garnet‐chlorite zone at the base, the chloritoid‐biotite zone and the biotite‐chlorite zone at the top of the nappe. The mineral isograds in the Selimiye nappe run parallel to the regional S_R foliation, parallel the Selimiye shear zone and indicate that the Selimiye shear zone formed during this prograde greenschist to lower amphibolite facies metamorphic event but remained active after the peak of metamorphism. ⁴⁰Ar/³⁹Ar mica ages and the tectonometamorphic relationship with the Eocene Cyclades–Menderes thrust, which occurs above the Selimiye nappe in the study area, suggests an Eocene age of metamorphism in the Selimiye nappe. Metasedimentary rocks of the Çine nappe 20–30 km north of the Selimiye shear zone record maximum P–T conditions of 8–11 kbar and 600–650 °C. An age of about 550 Ma is indicated for amphibolite facies metamorphism and associated top‐N shear in the orthogneiss of the Çine nappe. Our study shows that simple monophase tectonometamorphic fabrics do not always indicate a simple orogenic development of a nappe stack. Preservation in some areas and complete overprinting of those fabrics in other areas apparently occur very heterogeneously.     

Layer parallel shortening in salt-detached folds: constraint on cross-section restoration

Cleavage-fissility perpendicular to bedding is a common feature in the external part of fold-and-thrust belts. Three techniques were used to determine the internal distortion in the frontal Southern Pyrenees: the analysis of strain markers such as burrows and rain drops, the measurement of fissility, and the measurement of anisotropy of magnetic susceptibility (AMS). The comparison of the three techniques showed a good fit although they differ in sensitivity to penetrative strain variations in the range of deformation values explored in the study case. On the regional scale, the values of layer parallel shortening (LPS) derived from the markers analysis are very constant and account for 16–23% of shortening. These values are two to three times larger than the shortening values calculated from the restoration of the macroscopic scale structures and indicate a good decoupling above the Cardona salt Formation. This study permitted an accurate restoration of the low-amplitude el Guix detached anticline.     

深厚表土层地面注浆加固过程中井壁应变变化规律

分析了深厚表土层地面注浆加固过程中井壁的受力特点,介绍了金桥矿副井表土段地面注浆加固过程中井壁的应变观测结论,提出了深厚表土层井壁外注浆加固工程的井壁安全保证核心技术。