电容测试法判断测井电缆系统故障

测井电缆因长途颠簸、拉伸及绞车缠绕挤压,电缆连接器、电缆、绞车滑环、滑环连线等部位极易出现故障。电容测试法是一种简易、快速的检测方法,该法可在现场准确诊断出故障电缆的位置。以四芯铠装电缆为例,每根缆芯的正常阻值约为80Ω/1 000m,两缆芯间的分布电容约为170PPF/1 000m。在实际检测中,根据电容较小时测点的位置,可以有效判断故障部位;而电缆故障位置则可利用电阻及电容的线性关系进行计算予以确定。     

测井仪器的故障分析与排除思路

TYSC-3Q与PSJ-2型数字测井仪是目前煤田测井中常用的二种测井仪器,在使用过程中难免发生诸如测井控制故障、声速探管故障、密度三侧向探管故障、井温、井液电阻率探管故障、电法面板故障、数字测井面板故障、电测井故障等常见故障类型。通过对各类故障因素进行剖析,指出了故障易发生的部位,并详细的介绍了检查的方法及故障的排除步骤。     

贵州糯东井田水文地质条件分析

通过对井田内泉和暗河流量的调查研究,认为永宁镇组一、三段碳酸盐岩裂隙溶洞水为井田的主要含水层,含水层主要接受大气降水及河流的渗透补给;煤层上覆地层飞仙关组为相对隔水层,厚度大于500m,下覆无强含水层,其地下水对煤层的开采影响不大,井田水文地质条件较简单。采用比拟法对井田的涌水量进行了预算,推算该矿井开采设计涌水量为13 238m^3/d。     

南京市首级高程控制网的建立及跨江水准的研究

本文首先介绍了南京市首级高程控制网的概况,接着重点讨论了跨江水准测量方法的选择,并全面分析了测距三角高程法影响精度的三个因素,结合南京市首级高程控制网全面介绍了数据处理的有关问题。     

提高管线探测水平分辨率的技术方法

在平顶山矿工路路面改造工程中,使用GX-2型及RD-4000型地下管线探测仪探测地下管网布设情况。根据地下管线种类、管线布设方位、埋置深度、探测难度大小进行了多次试验,在此基础上确定了电磁探测技术与方法：利用直连法提高被测管线中的交变电流,压制邻近平行管线和地下介质中的异常反映;在多管并存、且间距较小的情况下,应选择“梯度法”对磁场水平分量垂直梯度ΔHx进行观测,以得到最大清晰异常;另外,还应根据具体情况,合理选择诸如压制旁侧管线法、选择发射法、偏移感应法、动源发射法等发射方式,保证目标管线中有较强异常呈现。在管线密集区,应尽可能地降低工作频率,以减小旁侧管线中产生的二次电流及二次磁场;为防止信噪比下降,可适当减小收发距,以提高接收机的灵敏度。     

Hybrid seismic modeling based on discrete-wave number and finite-difference methods

Any calculation of seismic wave propagation comprising the seismic source, the travel path, and the receiver site in a single finite-difference (FD) model requires a considerable amount of computer time and memory. Moreover, the methods currently available for including point sources in the 2D FD calculations are far-field approximations only. Therefore we have developed a new hybrid method for treating the seismic wave fields at localized 2D near-surface structures embedded in a 1D background medium, and excited by a point source. The source radiation and propagation in the background model is solved by the discrete-wave number (DW) method, while the propagation in the local 2D structure is calculated by the FD method. The coupling between the two sets of calculations is performed on a rectangular excitation box surrounding the local structure. We show the usefulness of the method in ground-motion studies where both near-field source effects and local site effects are important. Technical problems connected with the inconsistency between the 3D source radiation and the 2D FD calculation are minor for the relatively distant in-plane point explosive sources, but are more serious for the in-plane dislocation sources.     

Surface renewal analysis for sensible and latent heat flux density

High frequency temperature measurements were recorded at five heights and surface renewal (SR) analysis was used to estimate sensible heat flux density (H) over 0.1 m tall grass. Traces of the temperature data showed ramp-like structures, and the mean amplitude and duration of these ramps were used to calculate H using structure functions. Data were compared with H values measured with a sonic anemometer. Latent heat flux density (E) was calculated using an energy balance and the results were compared with E computed from the sonic anemometer data. SR analysis provided good estimates of H for data recorded at all heights but the canopy top and at the highest measurement level, which was above the fully adjusted boundary layer.     

The propagation of a single shear crack: A displacement discontinuity model

Numerical studies using the displacement discontinuity method show that a single shear crack under compression propagates in its own direction, because such propagation results in the maximum release of strain energy. The methods of linear elastic fracture mechanics may not be used for such a closed crack, and the stress intensity factors are meaningless in that case. Laboratory observations of propagation by means of kinks at an angle of approximately 70° to the crack may be due to heterogeneities, to the effect of a preexisting crack, to end effects, to microcracking, or to some combination of these factors. Such kinks may thus be local phenomena which cannot release most of the strain energy, and are not incompatible with our numerical results which are based on a global energy balance.     

About the specification of erosion flux for soft stratified cohesive sediments

The present paper deals with the specification of bed erosion flux that accounts for the effects of sediment-induced stratification in the water column. Owing to difficulties in measuring the bed shear stress _b and the erosive shear strength _s, we suggest a series of methods that combine laboratory and numerical experiments. A simplified turbulent transport model that includes these effects helps to quantify _b and _s. Focusing on soft stratified beds, the present study considers erosion rate formulas of the form =_f exp {[T_b-T_s]} where is a model constant (=1 for Gularte's (1978) formula and =1/2 for Parchure's (1984) formula). First, the bed erosive strength profile _s(Z) is adjusted by forcing the turbulent transport model with measured erosion rates. Second, three procedures are suggested to determine the erosion rate formula coefficients _f and : a global procedure and two different layer-by-layer procedures. Each procedure is applied to an erosion experiment conducted in a rotating annular flume by Villaret and Paulic (1986). The use of the layer-by-layer procedure based on a least squares fitting technique provides a closer fit than the global procedure. The present study points out the complementarity of experimental and numerical approaches and also suggests possible improvements in laboratory test procedures.