筒型基础沉贯阻力估算方法

系统地总结国外有代表性工程实践对筒型基础沉贯阻力的研究 ,并将各种方法综合起来 ,提出了加权综合估算法 ,供今后的研究和工程实践参考     

浅海桶形基础平台抗拔力与抗倾稳定分析

平台在海上受风、浪、流、冰等水平载荷作用产生倾斜 ,而土壤粘接力、摩擦力和土抗力是平台的抗拔和抗倾力 ,桶基平台应满足抗拔、抗倾稳定的要求 ,以保证平台的整体稳定性。讨论了桶基平台受水平力作用时 ,桶形基础的破坏模式及其计算方法 ,阐述了抗倾稳定计算方法     

Behavior of Pile Groups under Lateral Load

Based on investigation and model tests, and in combination with the research work on group effect for pile groups under lateral loads relating to the code of fixed offshore platforms, a series of studies have been performed on the behavior and failure mechanism of laterally loaded pile groups, critical pile spacing inducing group effect, lateral bearing capacity of pile groups and its main influence factors, the stress-strain relationship for single piles and pile groups and so on. Some new laws about non-uniformity of load distribution in the longitudinal direction of pile groups and load-deflection (p - y) curves for pile groups have been discovered, and an empirical formula is presented in order to remedy the defect of current calculating methods at home and abroad. These results can be used for reference in the design of pile foundation under lateral loads.     

海上平台桶形基础模型压力压贯与负压沉贯试验研究

介绍了海上平台桶形基础模型（模型桶）压力压贯和负压沉贯的试验概况,对比分析了两者贯入力的巨大差异和产生的原因,给出了模型桶压力压贯中贯入深度与压力的关系,负压没贯负压与贯入深度,抽吸泵流量,基土渗流量,桶内土塞隆起之间的关系,试验结果表明,负压沉贯可以大大降低以砂质粉土为基土的土抗力,为在胜利油田类似基土海域海上平台应用桶形基础提供了试验依据,为海上现场导管架桶形基础平台的安装就位施工和控制提供了     

不同软基处理方法适用性比较

总结分析了国内外现有的软土地基处理的各种方法。通过对采用不同方法进行软基处理的工程实例处理效果的定量对比，发现不同软基处理方法的适用性差异很大，多数工程中仅用一种方法很难达到设计要求，而两种或多种方法联合则可望取得更好的效果。     

桶形基础平台三维有限元稳定性分析

以我国第一座桶形基础采油平台工程实例为原型，采用三维有限元计算方法对桶形基础稳定性分析。平台在波浪、风等荷载作用下，其稳定性不仅与平台的整体结构有关，而且与桶形基础及其周围土体相互作用相关。在计算中，利用薄层摩擦单元模拟土与结构间的相互作用，取得了很好的效果。分析结果表明桶形基础采油平台在设计条件下运行是较为稳定的。     

新建水坝对下游已建水工建筑物的影响分析

分析了新建水坝及社会经济发展因素对坝下游水流及泥沙的影响，用一个简易河床模型来说明新建大坝后下游河床的演变规律，通过坝下游河床一般演变分析来阐述局部冲刷对已建水工建筑物基础的影响及对已建水工建筑基础的防护措施。     

半潜式超大浮体连接器动力特性的一种时间序列分析方法

根据刚性模块弹性连接器 (RMFC)假设研究由 3个模块连接而成的半潜式超大浮体MobileOffshoreBase(MOB)的波浪载荷动力响应。模块和连接器动力响应根据时间序列法计算 ,这种方法包括海况模拟 ,波浪载荷计算和结构响应计算三个主要部分。通过对结构的适当简化 ,根据Airy波理论 ,Morrison公式以及流体中的结构运动方程、弹性连接器变形方程 ,计算求得MOB在不规则海况下的动力响应 ,并将其与相关文献中的结果进行比较 ,表明该方法有良好的精确性     

Evaluation of bending moments and shear forces at unit connections of very large floating structures using hydroelastic and rigid body analyses

This paper investigates the characteristics of bending moments, shear forces and stresses at unit connections of very large floating structures (VLFS) under wave loads. The responses of VLFS are calculated by solving multi-body motion equation considering hydroelasticity and connection stiffness. Hydroelastic responses are calculated by the direct method. Higher-order boundary element method (HOBEM) is used for fluid analysis and finite element method (FEM) is introduced for structural analysis. The equation of motion is modified to describe the unit connections by employing spring elements. Bending moments and shear forces at the connections are obtained from the dynamic equilibrium condition for pressures and inertia forces. Two types of VLFS units such as tandem arranged units and side-by-side arranged units are considered in the numerical examples. The influences of connection stiffness, wave frequency and heading angle on responses of VLFS are investigated through the numerical examples. Rigid body analysis along with hydroelastic analysis is also carried out in the numerical analysis and comparison of those two approaches is discussed.     

Performance of hemi-cylindrical and rectangular submerged breakwaters

A parametric experimental study is conducted to compare the reflection and transmission characteristics of submerged hemi-cylindrical and rectangular rigid and water-filled flexible breakwater models. The results show that, for the rigid breakwaters, rectangular models are more effective than hemi-cylindrical ones in terms of reduction of transmitted waves. As for the flexible breakwaters, the hemi-cylindrical models may give better wave reflection than rectangular ones. However, the energy loss induced by the rectangular breakwaters is much larger and more significant to result in an overall better efficiency in terms of reduction in wave transmission. The effects of internal pressure show that the lowest pressurized flexible models considered in this work are the most effective in the reduction of the transmitted wave height. Higher wave reflection, lower wave transmission and higher energy loss are obtained consistently at the lower submergence depth ratio.