An evaluation of force-based design vs. direct displacement-based design of jointed precast post-tensioned wall systems

The unique features of jointed post-tensioned wall systems, which include minimum structural damage and re-centering capability when subjected to earthquake lateral loads, are the result of using unbonded post-tensioning to attach the walls to the foundation, along with employing energy dissipating shear connectors between the walls. Using acceptance criteria defined in terms of inter-story drift, residual drift, and floor acceleration, this study presents a multiplelevel performance-based seismic evaluation of two five-story unbonded post-tensioned jointed precast wall systems. The design and analysis of these two wall systems, established as the direct displacement-based and force-based solutions for a prototype building used in the PREcast Seismic Structural Systems （PRESSS） program, were performed at 60% scale so that the analysis model could be validated using the PRESSS test data. Both buildings satisfied the performance criteria at four levels of earthquake motions although the design base shear of the direct displacement-based jointed wall system was 50% of that demanded by the force-based design method. The study also investigated the feasibility of controlling the maximum transient inter-story drift in a jointed wall system by increasing the number of energy dissipating shear connectors between the walls but without significantly affecting its re-centering capability.     

Mechanical compression release device in steel bracing system for retrofitting RC frames

1 Introduction Braced steel frames are commonly used to resist seismic loads. Their seismic behavior was extensively studied during the past decades (Bertero et al.., 1989; Roeder, 1989; Jain, 1978). Their design is governed by the buckling behavior of the bracing members (ASCE, 1994,2002; CSA, 1994). To prevent or delay the seismic buckling of compressive members in concentrically braced frames in steel structures, a great number of methods have been proposed. These include the use of sp…     

Flexural performances of prestressed high strength concrete piles reinforced with hybrid GFRP and steel bars

Abstract

This study developed prestressed high-strength concrete (PHC) piles reinforced with high-strength materials (glass fiber-reinforced polymer (GFRP) bars) for flexural performance enhancement. Flexural strengths and behaviors of PHC piles reinforced with hybrid GFRP and steel bars were experimentally investigated, respectively. Large-scale specimens with total lengths of 12,000?mm and diameters of 600?mm were constructed and tested under bending, accompanied by evaluation of effects of non-prestressed reinforcement type and longitudinal reinforcement ratio. J-factors were calculated to evaluate deformability of all the specimens. PHC piles reinforced with GFRP bars were demonstrated to have much higher flexural capacity than those reinforced with steel bars. Moreover, strains at the midspans of cross sections of all the specimens basically conformed to the assumption of plane section. Failure of PHC piles reinforced with GFRP bars was attributable to gradual concrete crushing, while that of PHC piles reinforced with steel bars resulted from steel yielding. Results of this study were expected to provide theoretical basis for wide engineering applications of PHC piles reinforced with hybrid GFRP bars and steel bars in marine structures.     

新型珊瑚海水混凝土力学性能试验研究

为了解决全珊瑚海水混凝土(coral aggregate seawater concrete,简称CASC)的脆性问题,采用碱式硫酸镁水泥(basic magnesium sulfate cement,简称BMSC)为胶凝材料和剑麻纤维为增韧材料制备了一种新型全珊瑚海水混凝土(NCASC),系统测定了基本力学性能,并与普通硅酸盐水泥制备的CASC、碱式硫酸镁水泥砂石混凝土(basic magnesium sulfate cement concrete,简称BMSCC)、普通砂石混凝土(ordinary portland cement concrete,简称OPC)以及普通轻骨料混凝土(lightweight aggregate concrete,简称LAC)的力学性能进行对比。结果表明:立方体抗压强度(f_(cu),m)在15~35 MPa范围内的NCASC的轴心抗压强度(f_c,m)、劈裂抗拉强度(f_(sp),m)与f_(cu),m之间具有较显著的线性关系;对于f_(cu),m为15~35 MPa的混凝土,相同强度NCASC的f_c,m高于OPC、LAC及BMSCC,其f_c,m与f_(cu),m比值最大,大致在0.85~0.96之间,NCASC的f_(sp),m比OPC和LAC高,但比BMSCC低,且随着强度的提高,OPC与NCASC的f_(sp),m间的差距在增大,而LAC和BMSCC与NCASC的f_(sp),m间的差距在缩小;在强度等级C15~C55的范围中,NCASC和CASC的f_(sp),m、f_c,m与f_(cu),m之间的关系基本可以采用相同的线性回归方程来描述,利用这两个回归线性方程得到对应于标准强度等级的CASC和NCASC的f_(sp),m和f_c,m数据,为CASC力学性能研究与结构设计提供参考依据。     

喷涂聚脲弹性体技术在海港码头预应力大管桩上的应用

针对北仑电厂预应力大管桩表面潮湿,需候潮作业,施工条件复杂,施工作业时间短的特点,从表面处理、参数的设定、喷涂施工、质量控制及验收和存在问题及解决方案等方面,介绍了喷涂聚脲弹性体技术在已建海港码头预应力大管桩表面防腐保护工程中的应用情况。可为类似结构物的设计、施工、维护及管理提供参考。     

Effect of Fly Ash on Frost-Resistance and Chloride Ions Diffusion Properties of Marine Concrete

It is necessary to pay more attention to the durability of concrete undergoing freeze-thaw cycles and seawater attack simultaneously.Investigated are the effects of water-binder ratio,fly ash (FA) contents and air-entraining agent on resistance to frost and chloride diffusion of marine concrete blended with FA in natural seawater.The results show that fly ash does not improve the frost resistance of concrete but can improve its resistance to chloride diffusion by addition of less than 30%.The resistance to frost and chloride diffusion of FA concrete can be improved with the decrease of water-binder ratio,and FA may improve both of them simultaneously only being mixed with air-entraining agent.A ratio (named as R) of the frost-resisting durability factor to chloride diffusion coefficient can be used to evaluate the durability of marine concrete.Scanning electron microscope (SEM) analyses are consistent with the evaluations by the value of R.     

海洋环境下粉煤灰混凝土的抗冻性与抗氯离子渗透性的耦合

针对海洋环境条件,重点研究了粉煤灰混凝土的抗冻性和氯离子渗透性能的相互关系.试验分别研究了水胶比、粉煤灰等量取代水泥掺量大小、引气剂掺量等因素对抗冻性和抗氯离子渗透性能的影响,并与普通混凝土进行了对比.结果表明,粉煤灰不增加混凝土的抗海水冻融耐久性;粉煤灰增加混凝土的抗氯离子渗透性能,但是掺量超过30%,抗氯离子渗透性能下降;粉煤灰对混凝土抗冻性和抗氯离子渗透性的耦合影响在30%左右存在一个最佳掺量.为评估混凝土的抗冻性和氯离子扩散性的耦合性能,提出了新的评价方法--冻渗比(R值方法),并进行了试验验证.SEM和MIP微观分析与R值方法评价的结果是吻合的.     

上海洋山建港后港域夏季水文泥沙状况分析

对2007年9月17-26日在上海洋山港海域固定观测点(平均水深13 m)观测得到的水文泥沙要素,以及悬沙和底质样品分析.分析结果为:1)港域有效波高0.21-1.37 m(风速0.6～14.0 m/s),平均0.61 m(平均风速5.5 m/s).平静天气(平均风速小于5.0 m/s)下,波高随水深变化,两者的相关系数为0.899;而在强风天气下,波高受风况控制.2)最大表层流速超过2.00 m/s.大潮涨潮流占优势,小潮时落潮流占优势;与北岛链汉道封堵前相比,大潮涨、落潮平均流速分别减小15%和30%,小潮涨、落潮平均流速均减小30%～40%.各层余流均为西北方向,与涨潮流方向一致;垂向平均余流速0.11 cm/s,表层达0.25 m/s.3)离底高程1.35 m层和0.35m层最大悬沙浓度均大于3 kg/m3,两层平均悬沙浓度分别为0.89和0.95 kg/m3.无论大潮还是小潮涨潮悬沙浓度均大于落潮,这种现象在大潮时更为显著,潮周期中最大悬沙浓度出现在涨急.与工程前相比悬沙浓度明显降低,大、小潮降低均达20%.4)港区底质平均粒径9.0μm,工程后有变细的趋势.     

建筑物沉降观测技术方法探讨

随着城市建设的迅猛发展,城市规模越来越大,建筑物越来越高,由此带来的安全隐患越来越大,由于高层建筑一般采用桩基基础,且荷载较大,对高层建筑的内部基础和设备的位置关系有很高的精度要求,其施工安装阶段将给高层建筑本身及周边建筑群体带来复杂的形变影响。为了保障建筑物施工和运营的安全,就必须对其进行沉降观测。本文结合笔者多年的实际工作经验,并结合具体的实例,对高层建筑物沉降原因、沉降观测前的准备工作及沉降观测的实施过程和观测数据的处理方法等进行了论述,最后指出如何通过沉降观测技术准确地反映出高层建筑物的沉降情况。     

An answer to an important controversy and the need for caution when using simple models to predict inelastic earthquake response of buildings with torsion

This paper presents evidence that the extension of conclusions based on the widely used simplified, one story, eccentric systems of the shear‐beam type, to actual, nonsymmetric buildings and consequent assessments of the pertinent code provisions, can be quite erroneous, unless special care is taken to match the basic properties of the simplified models to those of the real buildings. The evidence comes from comparisons of results obtained using three variants of simplified models, with results from the inelastic dynamic response of three‐ and five‐story eccentric buildings computed with detailed MDOF systems, where the members are idealized with the well‐known plastic hinge model. In addition, a convincing answer is provided on a pertinent hanging controversy: For frame‐type buildings, designed in accordance with the dynamic provisions of modern codes (such as EC8 or IBC2000), which allow reduced shears at the stiff edge due to torsion, the frames at the flexible sides are the critical elements in terms of ductility demands. Copyright © 2009 John Wiley & Sons, Ltd.