不同预处理方法对尕海沉积物粒度测试的影响

湖泊沉积物粒度是研究湖区古环境演化的一个重要代用指标,粒度测量结果与预处理方法密切相关。从柴达木尕海湖岩心钻孔取48个样品,采用五种预处理方法,运用马尔文2000激光粒度仪进行粒度分析。结果显示经过预处理后平均粒径有不同程度的变细。单独加入H2O2除去样品中的有机质后,粒度分散变细最为明显,变幅可达10%左右,单独加入(NaPO3)6或H2O2处理后,>63μm(粗颗粒组分)粒径百分含量降低8个百分点左右。单独加蒸馏水浸泡、单独加HCl除去碳酸盐类胶结物和先后加H2O2、HCl(、NaPO3)6处理这三种方法分散效果不明显。23～33号样品对预处理的灵敏度最差,其他样品灵敏度稍好,但总体上尕海湖沉积物对预处理作用不敏感。对于性质类似的盐湖沉积物粒度测试,本文推荐加H2O2进行预处理。     

针对一次对流云降水反演大气垂直运动速度及雨滴谱

反演大气垂直速度和雨滴谱分布是研究云降水机制和云微物理信息的重要内容,对人工预报天气、干预天气都有重要意义。针对2021年8月29日安徽省内毫米波雷达探测到的一次对流云降水过程,处理毫米波雷达的功率谱数据并进行大气垂直速度和雨滴谱反演。在小粒子示踪法的基础上引入改进小粒子示踪法：选取有效云信号段中最小功率对应的谱点作为反演大气垂直速度的示踪物。首先,根据改进前后的小粒子示踪法分别从功率谱数据中反演大气垂直速度,并跟基数据反演大气速度的结果展开对比分析。进一步得到粒子在静止空气中的下落速度,根据现有粒子下落速度-粒子直径之间的经验公式计算反演粒子直径。研究表明：(1) 采用改进后的小粒子示踪法反演大气垂直速度得到的结果比小粒子示踪法得到的结果更精确,在云层内部两者误差较大;(2) 进一步得到粒子下落速度,结合探测时段的天气状况,得到的粒子速度与大气速度可很好地契合,跟对流云天气情况信息大致吻合;(3) 粒子浓度是反演雨滴谱分布时需要注意的主要参数,云在快速发展过程中,内部粒子持续朝外部扩张,云内部的粒子浓度较小,云边界的粒子浓度反而较大。     

Observational Evidence of High Ice Concentration in a Shallow Convective Cloud Embedded in Stratiform Cloud over North China

In this study we observed the microphysical properties, including the vertical and horizontal distributions of ice particles,liquid water content and ice habit, in different regions of a slightly supercooled stratiform cloud. Using aircraft instrument and radar data, the cloud top temperature was recorded as higher than -15℃, behind a cold front, on 9 September 2015 in North China. During the flight sampling, the high ice number concentration area was located in the supercooled part of a shallow convective cloud embedded in a stratiform cloud, where the ambient temperature was around -3℃. In this area,the maximum number concentrations of particles with diameter greater than 100 μm and 500 μm(N_(100) and N_(500)) exceeded 300 L~(-1) and 30 L~(-1), respectively, and were related to large supercooled water droplets with diameter greater than 24 μm derived from cloud–aerosol spectrometer probe measurements. The ice particles types in this region were predominantly columnar, needle, graupel, and some freezing drops, suggesting that the occurrence of high ice number concentrations was likely related to the Hallett–Mossop mechanism, although many other ice multiplication processes cannot be totally ruled out.The maximum ice number concentration obtained during the first penetration was around two to three orders of magnitude larger than that predicted by the Demott and Fletcher schemes when assuming the cloud top temperature was around-15℃.During the second penetration conducted within the stratiform cloud, N_(100) and N_(500) decreased by a factor of five to ten, and the presence of columnar and needle-like crystals became very rare.     

超高排土场的粒径分级及其边坡稳定性分析研究

明显的粒径分级是超高排土场区别于土质边坡的最重要特征。针对西源岭413台阶排土场,结合开发的HHC-CA模型和现场散体粒径分布情况的调查,建立了考虑超高排土场粒径分级特征的边坡模型。在此模型的基础上,借助FLAC3D软件分析了现状边坡和各种堆排模式下的边坡稳定性。结果表明:西源岭413台阶排土场现状边坡上部位移矢量表现为下沉,其下沉方向与坡面保持同向,中部位移矢量表现为剪切,下部位移矢量略有反抬升的趋势。其边坡破坏模式为顶部平台拉裂,中部以圆弧形剪出;此排土场的现状边坡处于暂时性稳定阶段。而采用全覆盖式多台阶排土的边坡上部位移矢量表现为下沉,在排土场底部过渡到水平方向;破坏模式为顶部平台拉裂,下部以圆弧形剪出。仅考虑堆积散体的材料强度对排土场稳定性影响时,超高排土场的粒径分级有利于排土场边坡的稳定。     

高压力下原状层间错动带三轴不排水剪切特性及其影响因素分析

针对某大型水电站揭露的原状层间错动带试样,模拟现场快速施工可能会产生的不排水边界条件,在围压5～30 MPa的高压力条件下开展了不固结不排水三轴试验,并结合试样物理性质的差异,分析讨论了原状层间错动带的力学特性。试样试验曲线和破坏模式主要由高围压控制：其应力-应变关系曲线均为应变硬化型且破坏后呈腰鼓状为塑性破坏。此外,较湿颗粒发生了大规模的颗粒破碎,其是造成高饱和度试样强度包线的趋势线随围压降低的根本原因。试验结果明显受物理性质影响造成了试验数据离散性,敏感性分析表明,围压P和饱和度 对初始弹性模量 和破坏强度 的影响最大,其次是孔隙比e,颗粒粒径（ ）分布对其影响程度最小。根据试样剪切特性建立的强度特征（ 和 ）初步预测公式可供实际工程参考。     

Effect of particle density and inflow concentration of suspended sediment on bedload transport in rill flow

Laboratory flume experiments were carried out to evaluate the effect of particle density on bedload transport of sand‐sized particles and the effect of a suspended load of clay particles (kaolinite) on bedload transport of sand‐sized particles in rill flow conditions. Three materials in the range 400–600 µm were selected to simulate bedload transport of primary particles and aggregates: sand (2650 kg/m³), crushed brick (2450 kg/m³) and anthracite (1300–1700 kg/m³). In the two first experiments, two different methods were applied to determine bedload transport capacity of coarse particles for various conditions of flow discharge (from 2 to 15 L/min) and slope (2.2, 3 and 4%). In the third experiment, clear water was replaced with kaolinite–water mixture and bedload transport capacity of crushed brick particles was determined for a 4% slope and different concentrations of kaolinite (0, 7, 41 and 84 g/L). The results showed that bedload transport increased significantly with the decrease in particle density but the effect of particle density on transport rates was much less important than flow discharge. Velocity measurements of clear flow, flow mixed with coarse particles and coarse particles confirmed the existence of a differentiation between suspended load and bedload. In these experimental conditions, suspended load of kaolinite did not affect bedload rates of crushed brick particles. Three transport capacity formulae were tested against observed bedload rates. A calibration of the Foster formula revealed that the shear stress exponent should be greater than 1.5. The Low and the Govers unit stream power (USP) equations were then evaluated. The Low equation was preferred for the prediction of bedload rates of primary particles but it was not recommended in the case of aggregates of low density because of the limited experimental conditions applied to derive this equation. Copyright © 2008 John Wiley & Sons, Ltd.     

The effect of discontinuity frequency on ground vibrations produced from bench blasting: A case study

A good number of empirical formulae and methods dealing with the analysis of the effects of blast-induced ground vibrations have been developed. The most common approach suggested for estimating the attenuation of particle velocity on the ground is to scale the distance (scaled distance, SD). This approach makes it possible to estimate the peak particle velocity when the amount of explosive charge or the distance or both are altered.Many parameters known to have an influence on particle velocity have been used for particle velocity prediction equations. Some of these parameters are maximum charge per delay, the distance between the station and shot location, burden, inelastic attenuation factor and site factors. However, the impacts of the discontinuities existing on the benches where blasts are detonated on the propagation velocity of seismic waves have not been taken into consideration in these equations.This study aims to examine the impacts of the discontinuity frequency parameter derived through geological measurements carried out on the blasting benches or nearby in a quarry mine (Supren, Eskisehir) in Turkey on the propagation of blast-induced ground vibrations. Developed based on the geological observations carried out on the benches, the model was formed by adding discontinuity frequency parameter to the particle velocity prediction model suggested by Nicholls et al. [Nicholls HR, Johnson CF, Duvall WI. Blasting vibrations and their effects on structures. Bulletin no. 656. Washington, DC: US Bureau of Mines; 1971]. In order to research the effect of the discontinuity frequency in the bench on the blast-induced ground vibrations, the relationship between the recorded peak particle velocity, scaled distance and discontinuity frequency was statistically evaluated for the site. The established relationship and the results of the study are presented.     

Estimating suspended sediment concentrations from turbidity measurements and the calibration problem

In situ turbidity meters are being increasingly used to generate continuous records of suspended sediment concentration in rivers. However, the usefulness of the information obtained depends heavily on the existence of a close relationship between fluctuations in suspended sediment concentration and turbidity and the calibration procedure that relates suspended sediment concentration to the turbidity meter's signal. This study assesses the relationship between suspended sediment concentration and turbidity for a small (1·19 km²) rural catchment in southern Brazil and evaluates two calibration methods by comparing the estimates of suspended sediment concentration obtained from the calibrated turbidity readings with direct measurements obtained using a USDH 48 suspended sediment sampler. With the first calibration method, the calibration relationship is derived by relating the turbidity readings to simultaneous measurements of concentration obtained from suspended sediment samples collected from the vicinity of the turbidity probe during flood events. With the second method, the calibration is based on the readings obtained from the turbidity meter when the probe immersed in samples of known concentration prepared using soils collected from the catchment. Overall, there was a close link between fluctuations in suspended sediment concentration and turbidity in the stream at the outlet of the catchment, and the estimates of sediment concentration obtained using the first calibration method corresponded closely with the conventionally measured sediment concentrations. However, use of the second calibration method introduced appreciable errors. When the estimated sediment concentrations were compared with the measured values, the mean errors were ± 122 mg l^?1 and + 601 mg l^?1 for the first and second calibration procedures respectively. Copyright © 2007 John Wiley & Sons, Ltd.     

刚性挡土墙主动土压力颗粒流模拟

将土体离散为具有滑动连接模型的刚性条块,用颗粒流PFC2D程序数值从细观力学角度模拟了墙体平移(T)、绕墙底转动(RB)和绕墙顶转动(RT)位移模式下不同位移大小时刚性挡土主动土压力分布。模拟结果表明：刚性挡墙主动土压力非线性分布、墙土间外摩擦角和土体剪切角或内摩擦角对土压力有很大影响;墙体绕顶部转动时,大约0.3倍墙高以上的主动土压力大于静止土压力产生土拱效应;模拟计算值与模型试验实测数据吻合比较好,具有一定的理论价值。     

考虑破碎的堆石料颗粒流数值模拟

以双江口300 m级高土石坝为工程背景,根据有关资料的试验数据,利用二维颗粒流计算机仿真技术对堆石料在一定围压下的颗粒破碎情况进行了数值模拟,数值试样由2 574个簇颗粒单元组成。数值模拟与室内平面应变试验结果对比表明,用选定的细观参数进行数值模拟与平面应变试验结果基本一致,说明用颗粒流方法进行数值模拟能够较好的再现堆石料的颗粒破碎特性。与室内试验相比,数值仿真模拟还能得到颗粒破碎的细观演化规律和破碎带的分布范围,从而为进一步建立考虑颗粒破碎的堆石坝本构模型,研究大坝填筑、水库蓄水过程以及地震情况下的颗粒破碎过程以及颗粒破碎所引起的坝体变形提供了一条途径。