Rock fracturing by explosive energy: review of state-of-the-art

A study of the dynamic rock fracture initiation and propagation due to explosive energy is presented through a detailed state-of-the-art review. Explosive energy dissipation in crushing and fracturing is examined and the various means to enhance the explosive energy utilization for dynamic rock fracturing are reviewed. The study highlights the need for a better understanding of the dynamic fracturing process particularly in the presence of in situ stresses in the rock mass.     

On the Importance of Geolithological Features for the Estimate of the Site Response: The Case of Catania Metropolitan Area (Italy)

The evaluation of seismic site response in the urban area of Catania was tackled by selecting test areas having peculiar lithological and structural features, potentially favourable to large local amplifications of ground motion. The two selected areas are located in the historical downtown and in the northern part of Catania where the presence of a fault is evident. Site response was evaluated using spectral ratio technique taking the horizontal- to-vertical component ratio of ambient noise. Inferences from microtremor measurements are compared with results from synthetic accelerograms and response spectra computed at all drillings available for this area. Such method is particularly suitable in urban areas where the nature of the outcropping geological units is masked by city growth and anthropic intervention on the surface geology. The microtremor H/V spectral ratios evaluated at soft sites located within the downtown profile tend to be smaller than that usually reported in the literature for such soils. A tendency for amplifications to peaks near 2 Hz is observed only in some sites located on recent alluvial deposits. Evidences for amplifications of site effects (frequency range 4–8 Hz) were observed in the sampling sites located on the fault, with a rapid decrease of spectral amplitude just a few tenths of metres away from the discontinuity. Numerical simulations evidenced the importance of geolithological features at depth levels even greater than 20–30 m. Besides this, the results strongly confirm the importance of the subsurface geological conditions, in the estimate of seismic hazard at urban scale.     

2-D deformation of two welded half-spaces due to a blind dip-slip fault

The solution of two-dimensional problem of an interface breaking long inclined dip-slip fault in two welded half-spaces is well known. The purpose of this note is to obtain the corresponding solution for a blind fault. The solution is valid for arbitrary values of the fault-depth and the dip angle. Graphs showing the variation of the displacement field with the distance from the fault, for different values of fault depth and dip angle are presented. Contour maps showing the stress field around a long dip-slip fault are also obtained     

Temperature dependence of large-scale water-retention curves: a case study

A local-scale model for temperature-dependence of water-retention curves may be applicable to large scales. Consideration of this temperature dependence is important for modeling unsaturated flow and transport in the subsurface in numerous cases. Although significant progress has been made in understanding and modeling this temperature effect, almost all the previous studies have been limited to small scales (on the order of several centimeters). Numerical experiments were used to investigate the possibility of extending a local-scale model for the temperature-dependence of water retention curves to large scales (on the order of meters). Temperature effects on large-scale hydraulic properties are of interest in many practical applications. Numerical experiment results indicate that the local-scale model can indeed be applicable to large-scale problems for special porous media with high air entry values. A typical porous medium of this kind is the porous tuff matrix in the unsaturated zone of Yucca Mountain, Nevada, the proposed geologic disposal site for national high-level nuclear wastes. Whether this finding can approximately hold for general cases needs to be investigated in future studies.     

Initiation and development of pull-apart basins with Riedel shear mechanism: insights from scaled clay experiments

Typical pull-apart structures were created in scaled clay experiments with a pure strike-slip geometry (Riedel type experiments). A clay slab represents the sedimentary cover above a strike-slip fault in the rigid basement. At an early stage of the development of the deformation zone, synthetic shear fractures (Riedel shears) within the clay slab display dilatational behaviour. With increasing basal displacement the Riedel shears rotate and open further, developing into long, narrow and deep troughs. The shear displacement and the low angle with the prescribed principal basal fault set them apart from tension gashes. At a more evolved stage, synthetic segments (Y-shears) parallel to the basal principal fault develop and accommodate progressive strike-slip deformation. The Y-shears connect the tips of adjacent troughs developed from the earlier Riedel shears, resulting in the typical rhomb-shaped structures characteristic for pull-apart basins. The Strait of Sicily rift zone, with major strike-slip systems being active from the Miocene to the Present, comprises pull-apart basins at different length scales, for which the structural record suggests development by a mechanism similar to that observed in our experiments.