Three dimensional seismic studies of deep-water hazard-related features on the northern slope of South China Sea

Mass transport deposits and geological features related to fluid flow such as gas chimneys, mud diapirs and volcanos, pockmarks and gas hydrates are pervasive on the canyon dominated northern slope of the Pearl River Mouth basin of the South China Sea. These deposits and structures are linked to serious geohazards and are considered risk factors for seabed installations. Based on high resolution three dimensional seismic surveys, seismic characteristics, distributions and origins of these features are analyzed. A distribution map is presented and geometrical parameters and spatial distribution patterns are summarized. Results show that various groups of the mapped features are closely tied to local or regional tectonism and sedimentary processes. Mass transport complexes are classified as slides near the shelf break, initially deformed slumps on the flanks of canyons and highly deformed slumps on the lower slope downslope of the mouth of canyons. We propose them to be preconditioned by pore pressure changes related to sea level fluctuations, steep topography, and fluid and fault activities. Gas chimneys are mainly located in the vicinity of gas reservoirs, while bottom-simulating reflectors are observed within the gas chimney regions, suggesting gas chimneys serve as conduits for thermogenic gas. Mud diapirs/volcanos and pockmarks are observed in small numbers and the formation of pockmarks is related to underlying gas chimneys and faults. This study aims at reducing risks for deep-water engineering on the northern slope of South China Sea.     

近期黄河入海水量减少成因分析

利用黄河入海控制站利津的实测水文资料及黄河流域的降水和人类活动影响的相关资料等,分析了近期黄河入海水量变化的特征及变化的原因。结果表明,1986年以来黄河入海水量大幅减少,断流现象突出等,与其以前相比,入海水量减少64%;在减少的水量中,“准自然因素影响”约占55%,引黄用水约占31.5%,其它人类活动影响约占13.5%。     

酉阳河流域典型年汛期的基流分割研究

基流分割是水文学研究中的重难点问题之一,目前基流分割也存在许多方法.基于酉阳河典型年汛期实测日平均流量资料,分别采用Chapman-Maxwell改进方程数字滤波法一次滤波(参数N=1)以及二次滤波(参数N=2)、BFI(f)法、HYSEP固定步长法、HYSEP滑动步长法、HYSEP局部最小值法进行基流分割并对其结果进...     

Curvature derived from LiDAR digital elevation models as simple indicators of debris-flow susceptibility

To mitigate the damage caused by debris flows resulting from heavy precipitation and to aid in evacuation plan preparation, areas at risk should be mapped on a scale appropriate for affected individuals and communities. We tested the effectiveness of simply identifying debris-flow hazards through automated derivation of surface curvatures using LiDAR digital elevation models. We achieved useful correspondence between plan curvatures and areas of existing debris-flow damage in two localities in Japan using the analysis of digital elevation models(DEMs). We found that plan curvatures derived from 10 m DEMs may be useful to indicate areas that are susceptible to debris flow in mountainous areas. In residential areas located on gentle sloping debris flow fans, the greatest damage to houses was found to be located in the elongated depressions that are connected to mountain stream valleys. Plan curvaturederived from 5 m DEM was the most sensitive indicators for susceptibility to debris flows.     

An efficient hybrid integral-equation method for point-absorber wave energy converters with a vertical axis of symmetry

To assist in the prototyping and controller design of point-absorber wave energy converters (WECs), an easy-to-implement hybrid integral-equation method is presented for computing the frequency-domain hydrodynamic properties of bodies with a vertical axis of symmetry in waves. The current hybrid method decomposes the flow domain into two parts: an inner domain containing the body and an outer domain extending to infinity. The solution in the inner domain is computed using the boundary-element method, and the outer-domain solution is expressed using eigenfunctions. Proper matching at the domain boundary is achieved by enforcing continuity of velocity potential and its normal derivative. Body symmetry allows efficient computation using ring sources in the inner domain. The current method is successfully applied to three different body geometries including a vertical truncated floating cylinder, the McIver toroid, and the coaxial-cylinder WEC being developed in the authors’ laboratory. In particular, the current results indicate that, by replacing the flat bottom of the coaxial-cylinder WEC with the Berkeley-Wedge (BW) shape, viscous effect can be significantly reduced with only minor negative impact on wave-exciting force, thus increasing WEC efficiency. Finally, by comparing to experimental measurements, the current method is demonstrated to accurately predict the heave added mass and wave-exciting force on the coaxial-cylinder WEC with BW geometry. If a viscous damping correction factor is used, the heave motion amplitude can also be accurately computed.     

含沙浑水体的黏度测量及应用分析

含沙浑水体的高速冲击会对海底构筑物造成破坏,在计算浑水体对构筑物的作用力时,黏度是一项重要参数。本文利用落球试验和流变仪测试试验,测定了不同浓度含沙浑水体的黏度,给出其起始黏度与动力作用后的稳定黏度。结果表明:含沙量在大于400g/L时,浑水体为可用赫巴模型描述的非牛顿流体,并可简化为宾汉体;在含沙量小于400g/L时,浑水体仍可用宾汉体模型描述,在忽略较小的初始剪切应力时,可简化为牛顿流体。浓度大于400g/L的浑水体的起始黏度约为稳定黏度的100倍。文中讨论了含沙浑水体起始黏度与稳定黏度在工程计算应用中的适用情况。     

不同开口比人工鱼礁体水动力特性及礁体稳定性研究

为研究方型人工鱼礁体开口比的变化对其水动力特性的影响,利用Fluent软件模拟了边长为3m、开口比为0～0.6之间7种不同方型鱼礁体周围水流场,通过分析水流场变化规律得到了礁体流场效应、阻力系数随开口比的变化情况;基于Morison方程计算了礁体在波流作用下的受力及其抗滑移、抗倾覆安全系数。研究结果表明:当礁体开口比小于0.2时,背涡区范围较大,流场效应明显;随着开口比的增大,礁体产生的上升流范围及竖直向最大速度分量逐渐减小;对于方形开口礁体,阻力系数与开口比的关系式为Cd=0.875φ+1.088(R2=0.963,P<0.01);随着开口比的增大,礁体所受最大波流作用力、抗滑移及抗倾覆安全系数逐渐减小,但礁体不会发生滑移和倾覆,可为实际礁体结构的设计提供参考。     

Numerical study on scale effect of form factor

The scale effect of form factor is investigated via a numerical approach in this paper, where the turbulent ship flow is computed by solving the steady and incompressible Reynolds-averaged Navier-Stokes and continuity equations. A wall function approach is employed to bridge the near-wall and outer turbulent flow region. The numerical scheme based on a finite-volume formulation is applied to discretize the coupled governing equation. For the sake of numerical stability, accuracy and economy, an identical grid is employed to compute ship flow at different Reynolds number, where the grid is optimized for the medium Reynolds number of the investigated range. Four surface ships and two sub-bodies with notably different geometrical characteristics are chosen as the investigated cases, where double-model flow without appendages is computed. The calculated total resistance coefficient shows a decreasing tendency against Reynolds number among all studied hulls. Similar to the calculated total resistance coefficient, the calculated friction resistance coefficient decreases with the Reynolds number and varies relatively little for a given Reynolds number among different hulls. The viscous pressure resistance coefficient is less insensitive to the Reynolds number but apparently depends on hull form. Compared with the form factor calculation based on empirical friction lines, the flat-plate friction prediction based on CFD approach clearly gives smaller Re-dependent form factor, which should more realistically reflect the scale effect of form factor. The form factor exhibits a near linear and increasing dependence on Reynolds number. The numerical results show that the dependence of r_P on Reynolds number mainly governs the scale effect of form factor.     

Regional hydrologic mapping of flows in stream networks

River low flow (LF) is an important hydrological characteristic used in management of the quantity and quality of water resources. A common way to transpose at-station low flow quantiles to ungaged locations involves development of regional multivariate regression models. In site selection studies of water control facilities, need arises to automate the mapping of LF characteristics onto the stream network in a continuous manner. This would allow estimation of LF at any desired ungaged location. A mapping algorithm is introduced that determines the value of regression model's independent variables (input components) over the drainage area of each stream pixel and calculates the flow (output). The mapping algorithm relies mainly on the digital elevation model (DEM) and its derivatives, such as flow direction and flow accumulation. Furthermore, the contribution of each independent variable of the regional model to the total flow may be plotted to represent the flow profiles along the streams. A case study involving LF mapping in rivers of Gilan province, Iran, where LF quantiles are required for issuing water withdrawal permits as well as maintaining water quality standards, is also described in the paper. Overall, the maps and profiles of flow statistics in the region of interest provide convenient visualization and assessment tools for water resource and environmental engineers. The transposition algorithm may also be applied in regional mapping of other flow characteristics such as flood or average flows.     

Numerical flow and performance analysis of a water-jet axial flow pump

The purpose of the present study is to investigate the performance and three-dimensional flow fields in a water-jet pump. TASCflow is employed to simulate the rotator-stator coupling flow field. A standard k-ε turbulence model combined with standard wall functions is used. In order to investigate the effect of a rear stator on flow fields, the flows in two water-jet pumps with and without a rear stator are studied. Computational fluid dynamics (CFD)-predicted overall performances are in good agreement with the experimental results. Then the flow fields, such as the pressure distribution on the blade surfaces, and the axial and tangential velocity distribution, especially the radial loading distribution, are investigated at different flow rates. In addition, the effects of a rear stator and different spacings between the rotor and the stator on the overall performance and the flow fields of the water-jet pump are also investigated.