T106产品中700hPa垂直速度和水汽能量与塔城大降水关系的探讨

对塔城盆地1998－1999年15个大降水个例进行了诊断分析，发现了T106产品700hPa垂直速度和水汽通量与塔城盆地大降水量级呈正相关，并给出了定量预报指标。     

A mathematical hysteretic model for elastomeric isolation bearings

An analytical model for high damping elastomeric isolation bearings is presented in this paper. The model is used to describe mathematically the damping force and restoring force of the rubber material and bearing. Ten parameters to be identified from cyclic loading tests are included in the model. The sensitivity of the ten parameters in affecting the model is examined. These ten parameters are functions of a number of influence factors on the elastomer such as the rubber compound, Mullins effect, scragging effect, frequency, temperature and axial load. In this study, however, only the Mullins effect, scragging effect, frequency and temperature are investigated. Both material tests and shaking table tests were performed to validate the proposed model. Based on the comparison between the experimental and the analytical results, it is found that the proposed analytical model is capable of predicting the shear force–displacement hysteresis very accurately for both rubber material and bearing under cyclic loading reversals. The seismic response time histories of the bearing can also be captured, using the proposed analytical model, with a practically acceptable precision. Copyright © 2002 John Wiley & Sons, Ltd.     

Comparative response analysis of conventional and innovative seismic protection strategies

The paper presents a numerical investigation aimed at evaluating the improvements achievable through devices for passive seismic protection of buildings based on the use of shape memory alloys (SMA) in place of conventional steel or rubber devices. To get some generality in the results, different resisting reinforced concrete plane frames were analysed, either protected or not. ‘New’ and ‘existing’ buildings were considered depending on whether seismic provisions are adopted in the building design or not. Base isolation and energy dissipation were equally addressed for both conventional and innovative SMA‐based devices. Fragility analyses were performed using specific damage measures to account for comparisons among different damage types; the results were then used to estimate quantitatively the effectiveness of the various protection systems. More specifically, the assessment involved a direct comparison of the damage reduction provided by each protection system with respect to the severe degradation experienced by the corresponding non‐protected frame. Structural damage, non‐structural damage and damage to contents were used on purpose and included in a subsequent phase of cost analysis to evaluate the expected gains also in terms of economic benefits and life loss prevention. The results indicate that base isolation, when applicable, provides higher degrees of safety than energy dissipation does; moreover, the use of SMA‐based devices generally brings about better performances, also in consideration of the reduced functional and maintenance requirements. Copyright © 2002 John Wiley & Sons, Ltd.     

Seismic response of self‐centring hysteretic SDOF systems

The seismic response of single‐degree‐of‐freedom (SDOF) systems incorporating flag‐shaped hysteretic structural behaviour, with self‐centring capability, is investigated numerically. For a SDOF system with a given initial period and strength level, the flag‐shaped hysteretic behaviour is fully defined by a post‐yielding stiffness parameter and an energy‐dissipation parameter. A comprehensive parametric study was conducted to determine the influence of these parameters on SDOF structural response, in terms of displacement ductility, absolute acceleration and absorbed energy. This parametric study was conducted using an ensemble of 20 historical earthquake records corresponding to ordinary ground motions having a probability of exceedence of 10% in 50 years, in California. The responses of the flag‐shaped hysteretic SDOF systems are compared against the responses of similar bilinear elasto‐plastic hysteretic SDOF systems. In this study the elasto‐plastic hysteretic SDOF systems are assigned parameters representative of steel moment resisting frames (MRFs) with post‐Northridge welded beam‐to‐column connections. In turn, the flag‐shaped hysteretic SDOF systems are representative of steel MRFs with newly proposed post‐tensioned energy‐dissipating connections. Building structures with initial periods ranging from 0.1 to 2.0s and having various strength levels are considered. It is shown that a flag‐shaped hysteretic SDOF system of equal or lesser strength can always be found to match or better the response of an elasto‐plastic hysteretic SDOF system in terms of displacement ductility and without incurring any residual drift from the seismic event. Copyright © 2002 John Wiley & Sons, Ltd.     

A recursive decomposition algorithm for network seismic reliability evaluation

A new probabilistic analytical approach to evaluate seismic system reliability of large lifeline systems is presented in this paper. The algorithm takes the shortest path from the source to the terminal of a node weight or edge weight network as decomposition policy, using the Boolean laws of set operation and probabilistic operation principal, a recursive decomposition process then could be constructed. For a general weight network, the modified Torrieri method (NTR/T method) is introduced to combine with the suggested algorithm. Therefore, the recursive decomposition algorithm may be applied to evaluate the seismic reliability of general lifeline systems. A series of case studies, including a practical district electric power network system and a large urban water supply system, show that the suggested algorithm supplies a useful probabilistic analysis means for the seismic reliability evaluation of large lifeline systems. Copyright © 2002 John Wiley & Sons, Ltd.     

A response‐based decoupling criterion for multiply‐supported secondary systems

It is often infeasible to carry out coupled analyses of multiply‐supported secondary systems for earthquake excitations. ‘Approximate’ decoupled analyses are then resorted to, unless the response errors due to those are significantly high. This study proposes a decoupling criterion to identify such cases where these errors are likely to be larger than an acceptable level. The proposed criterion is based on the errors in the primary system response due to decoupling and has been obtained by assuming (i) the input excitation to be an ideal white noise process, (ii) cross‐modal correlation to be negligible, and (iii) the combined system to be classically damped. It uses the modal properties of the undamped combined system, and therefore, a perturbation approach has been formulated to determine the combined system properties in case of light to moderately heavy secondary systems. A numerical study has been carried out to illustrate the accuracy achieved with the proposed perturbation formulation. The proposed decoupling criterion has been validated with the help of two example primary‐secondary systems and four example excitation processes. Copyright © 2002 John Wiley & Sons, Ltd.     

Pseudodynamic tests on rubber base isolators with numerical substructuring of the superstructure and strain‐rate effect compensation

A pseudodynamic testing procedure has been applied by which the seismic response of a base‐isolated building is obtained by using as specimen the isolators, while the superstructure is numerically simulated. The procedure also takes advantage of the continuous pseudodynamic testing capabilities of the ELSA laboratory, which increase the accuracy of the results and reduce the strain‐rate effect of the rubber bearings. A simple proportional correction of the measured forces compensates the remaining strain‐rate effect due to the unrealistic speed of the test. The correction factor is obtained by means of a characterizing test on the specific rubber isolators. The developed method has been successfully applied to the prediction of the seismic response of a base‐isolated four‐storey building submitted to several specified accelerograms. The results for those earthquakes as well as the effects of some changes of the parameters of the system are discussed. Copyright © 2002 John Wiley & Sons, Ltd.     

Towards a direct collapse–load method of design for concrete frames subjected to severe ground motions

Most current methods of design for concrete structures under earthquake loads rely on highly idealized ‘equivalent’ static representations of the seismic loads and linear‐elastic methods of structural analysis. With the continuing development of non‐linear methods of dynamic analysis for the overload behaviour and collapse of complete concrete structures, a more direct and more accurate design procedure becomes possible which considers conditions at system collapse. This paper describes an evaluation procedure that uses non‐linear dynamic collapse–load analysis together with global safety coefficients. A back‐calibration procedure for evaluating the global safety coefficients is also described. The aim of this paper is to open up discussion of alternative methods of design with improved accuracy which are necessary to move towards a direct collapse–load method of design. Copyright © 2002 John Wiley & Sons, Ltd.     

Study on effects of damping in laminated rubber bearings on seismic responses for a ⅛ scale isolated test structure

The effects of damping in various laminated rubber bearings (LRB) on the seismic response of a ?‐scale isolated test structure are investigated by shaking table tests and seismic response analyses. A series of shaking table tests of the structure were performed for a fixed base design and for a base isolation design. Two different types of LRB were used: natural rubber bearings (NRB) and lead rubber bearings (LLRB). Three different designs for the LLRB were tested; each design had a different diameter of lead plug, and thus, different damping values. Artificial time histories of peak ground acceleration 0.4g were used in both the tests and the analyses. In both shaking table tests and analyses, as expected, the acceleration responses of the seismically isolated test structure were considerably reduced. However, the shear displacement at the isolators was increased. To reduce the shear displacement in the isolators, the diameter of the lead plug in the LLRB had to be enlarged to increase isolator damping by more than 24%. This caused the isolator stiffness to increase, and resulted in amplifying the floor acceleration response spectra of the isolated test structure in the higher frequency ranges with a monotonic reduction of isolator shear displacement. Copyright © 2002 John Wiley & Sons, Ltd.     

地震勘探资源频率域叠加方法研究

在叠前共深度点道集内各地震道的动、静校正误差很小的情况下，地震资料时间域水平叠加方法有较好的叠加结果。但是，如果动、静校正的误差较大时，叠加效果将受到影响，即叠后振幅和分辨率都会降低。因此，提出一种频率域叠加方法。该方法既具有常规水平叠加方法能提高信噪比的优点，又能将共深度点道集内的走时时差消除，达到内相叠回的目的。几个比较叠加方法效果的有噪CDP道集叠加的例子证明了该方法的效果。