Sliding fragility of block‐type non‐structural components. Part 1: Unrestrained components

Motivated by the development of performance‐based design guidelines with emphasis on both structural and non‐structural systems, this paper focuses on seismic vulnerability assessment of block‐type unrestrained non‐structural components under sliding response on the basis of seismic inputs specified by current seismic codes. Two sliding‐related failure modes are considered: excessive relative displacement and excessive absolute acceleration. It is shown that an upper bound for the absolute acceleration response can be assessed deterministically, for which a simple yet completely general equation is proposed. In contrast, fragility curves are proposed as an appropriate tool to evaluate the excessive relative displacement failure mode. Sample fragility curves developed through Monte‐Carlo simulations show that fragility estimates obtained without taking into account vertical base accelerations can be significantly unconservative, especially for relatively large values of the coefficient of friction. It is also found that reasonable estimates of relative displacement response at stories other than the ground in multistorey buildings cannot in general be obtained by simply scaling the ground acceleration to the peak acceleration at the corresponding storey. Failure modes considered in this study are found to be essentially independent of each other, a property that greatly simplifies assessment of conditional limit states. Copyright © 2002 John Wiley & Sons, Ltd.     

A procedure for evaluating seismic energy demand of framed structures

Energy serves as an alternative index to response quantities like force or displacement to include the duration‐related seismic damage effect. A procedure to evaluate the absorbed energy in a multistorey frame from energy spectra was developed. For low‐ to medium‐rise frames, it required a static pushover analysis of the structure to determine the modal yield force and ductility factor of an equivalent single‐degree‐of‐freedom system for the first two modes. The energy spectra were then used to determine the energy contribution of each mode. A procedure was also developed to distribute the energy along the frame height based on energy shapes. This study showed that the second‐mode response in some cases needs to be considered to reflect the energy (or damage) concentration in the upper floors. Copyright © 2002 John Wiley & Sons, Ltd.     

高职GIS专业实践教学及实践基地建设

高职教育是GIS人才培养的重要组成部分。本文通过介绍职教GIS专业的建设，探索GIS实践教学与实践基地建设模式、方法及对人才培养的影响。     

Observing artificially induced strain: implications for subglacial deformation

By analysing a series of four successive thin‐sections from a ceramic clay that was subjected to uniaxial compression, we were able to monitor the development of microstructures in a fine‐grained sediment. The artificially induced microstructures, such as unidirectional clay reorientations and linear and circular grain arrangements, are identical to features that have been observed in thin‐sections of subglacially deformed tills, and therefore may be used as representative analogues. We argue that the structures, reflecting slip, planar shear displacements as well as rotational movements, can be explained by assuming a Coulomb‐plastic response to imposed shear. We conclude that sediments subjected to subglacial deformation behave as Coulomb materials, at least during the final stages of the deformation. The present study bridges the gap between field studies, experimental studies and theoretical modelling. The microscopic observations assist in visualising inferred subglacial processes and facilitate up‐ and downscaling between diverse methodological approaches. Copyright © 2003 John Wiley & Sons, Ltd.     

Compression mechanisms of coesite

 The structure of coesite has been determined at ten pressures up to a maximum of 8.68 GPa by single-crystal X-ray diffraction. The dominant mechanism of compression is the reduction of four of the five independent Si–O–Si angles within the structure. There is no evidence of the fifth linkage, Si1–O1–Si1, deviating from 180°. Some Si–O bond distances also decrease by up to 1.6% over the pressure range studied. The pattern of Si–O–Si angle reduction amounts to a rotation of the Si2 tetrahedron around the [001] direction. This rotation induces significant internal deformation of the Si1 tetrahedron. Comparison of the experimental data with rigid-unit distance least-squares simulations of coesite suggests that this pattern of compression, the anomalous positive values of both s₂₃ and K′′ in the equation of state of coesite, its high elastic anisotropy and the unusual straight Si1–O1–Si1 linkage within the structure are all consequences of the connectivity of the tetrahedral framework. Received: 11 July 2002 / Accepted: 14 January 2003 Acknowledgements The help of Christian Baerlocher of ETH Zurich in providing both the DLS-76 software and advice in its use is gratefully acknowledged, as are discussions with Paul Ribbe of Virginia Tech and the comments of two anonymous reviewers. The data analysis was supported by the National Science Foundation under grant EAR-0105864 to N.L. Ross and R.J. Angel.     

Atomistic simulation of the structure and elastic properties of pyrite (FeS2) as a function of pressure

Interatomic potential parameters have been derived at simulated temperatures of 0 K and 300 K to model pyrite FeS₂. The predicted pyrite structures are within 1% of those determined experimentally, while the calculated bulk modulus is within 7%. The model is also able to simulate the properties of marcasite, even though no data for this phase were included in the fitting procedure. There is almost no difference in results obtained for pyrite using the two potential sets; however, when used to model FeS₂ marcasite, the potential fitted at 0 K performs better. The potentials have also been used to study the high-pressure behaviour of pyrite up to 44 GPa. The calculated equation of state gives good agreement with experiment and shows that the Fe–S bonds shorten more rapidly that the S–S dimer bonds. The behaviour of marcasite at high pressure is found to be similar to that of pyrite.     

复合纤维加固钢筋混凝土梁受剪性能试验研究

对14根钢筋混凝土矩形梁进行抗剪加固试验，研究在受剪区粘贴高强复合纤维的加固效果和设计方法。主要分析了纤维粘贴量、包裹方法和剪跨比等因素对钢筋混凝土加固梁受剪性能的影响和作用。对试验梁进行了全过程分析，并基于试验结果，提出了抗剪加固设计中复合纤维设计应变的合理取值和计算公式，阐述了具体加固设计模型和设计方法。     

中国夏季降水异常空间模与副热带高压的关系

本文用1959～1994年6、7、8月全国范围47个5°×5°经纬度网格降水资料分析了夏季降水异常空间模的月际差异，并在此基础上用西太平洋副高指数及青藏高原指数#FKB#FS分析降水异常空间模与环流的关系，为检验环流指数与降水相关场的整体信度，还对8月份降水资料进行了Monte-Carlo检验。结果表明，夏季总降水异常的空间模在每一月份中并非表现得同样清楚，江淮流域与河套及华南的反相关在8月份表现得最清楚。而青藏高原中东部南北两侧的负相关在6月及8月很清楚，7月份次之。8月份西太平洋副高北界异常对江淮流域与河套及华南地区降水异常反相关的产生有很大作用。副高稳定偏北时，河套、华南易涝，江淮易旱。反之亦然。青藏高原指数#FKB#FS与逐月降水的相关分析表明，青藏高原上高压及低涡活动对高原中东部南北两侧负相关的产生有一定作用。当高压活动偏多时，北侧易旱、南侧易涝。并且6月及8月的作用较大，7月较小。另外，8月份副高活动对这一降水异常空间模的产生也有一定影响。     

国外中期数值预报业务模式的性能及发展趋势

作者简单介绍了国内预报员较为熟悉的欧洲中期天气预报中心，美国国家气象中心和日本气象厅三个中期预报模式的性能及预报效果，包括近几年颇为流行的半拉格朗日时间积分方案，物理过程参数化方案的完善和改进，中期数值预报业务模式的发展趋势等。     

西藏聂拉木高喜马拉雅结晶岩系的伸展变形

西藏聂拉木高喜马拉雅结晶岩系在区域上以单一的叶理和单一的拉伸线理占主要地位，其变形带的组构主要反映了透入性的伸展变形；根据显微构造分析表明早期由北往南推覆，晚期由南向北伸展，且晚期表现非常明显。