坝基碎屑岩三轴蠕变特性及长期强度试验研究

基于物理和常规变形特性分析,认为某水电站坝基碎屑岩力学特性异常复杂,故采用岩石三轴伺服仪开展了系列的蠕变力学特性试验研究。首先,探讨了轴向、侧向及体积蠕变特性和速率变化规律;其次,分析了蠕变对偏应力-应变特性影响并开展了破坏岩样微细观电镜扫描试验;最后,在采用等时曲线簇法确定长期强度的基础上,以实际延性扩容为依据,认为岩石侧向体积扩容速率大于轴向压缩速率的临界点为快速蠕变破坏的标志,提出确定长期强度的新方法。结果表明,碎屑岩表现出显著的蠕变特性,蠕变曲线主要分为初始衰减和稳态蠕变两阶段,且最后一级应力施加后呈现加速蠕变现象;应力增加导致蠕变变形加剧,最终破坏表现出轴向压缩变形过大、体积延性扩容明显、稳态蠕变速率较大等特点,且蠕变速率与应力符合指数函数关系。岩样长期强度与三向稳态蠕变速率交点和侧向体积扩容应力阀值基本一致,为常规强度的54%～80%。试验结果旨在为相关岩石工程长期稳定分析及蠕变模型构建提供可靠的依据。     

汶川8.0级地震的余震触发作用和对断层的应力加卸载作用

采用可变滑动震源模型,计算和研究了汶川M_S 8.0地震产生的应力变化及对后续6次强余震的应力触发作用,并定量分析了汶川地震对附近活动断裂带的库仑应力加卸载作用。结果显示:汶川地震产生的库仑破裂应力变化分布图案复杂性强,主要由发震断裂复杂的空间展布形态以及震源断层活动具有逆冲兼右旋走滑两种性质决定。汶川地震产生的库仑破裂应力变化对多数强余震存在一定的触发作用。汶川地震的发生对附近的断裂带有不同程度的影响,其中青川断裂中段和北段、岷江断裂南段和灌县-江油断裂南段,主要是以强烈的库仑破裂应力加载作用占主导地位,有利于强余震序列的孕育、加速以至于发生;东昆仑断裂带和鲜水河断裂带受到了轻微的应力加载作用;龙泉山断裂带、华莹山断裂带和西秦岭北缘断裂带主要受到了轻微的卸载作用。     

落石冲击混凝土板与缓冲层组合结构的动力响应

钢筋混凝土（RC）板与一定厚度的土颗粒缓冲层组合结构被广泛用于山区高位单体及群发性崩塌落石的防治,为研究此类防护结构在落石作用下的冲击力衰减规律及RC板的破坏模式,开展了室外系列落石冲击试验。结果表明,增大缓冲层厚度能够有效减小最大冲击力,峰值加速度随缓冲层厚度减小而增大,尤其在缓冲层厚度为0.1 m及0.2 m时,最大值急剧增大,峰值加速度与缓冲层厚度的变化满足指数函数关系;根据量纲分析原理得到缓冲层最大冲击深度与动能的平方成正比、与最大入射冲击力成反比的计算公式,且与实测值较吻合;入射冲击力在缓冲层内的衰减率随缓冲层厚度的增加以指数函数递增,在0.6 m缓冲层厚度下可使峰值冲击力衰减70%左右;随累积冲击能级的增大,RC板经历了弯曲起裂及扩展、次级弯曲裂纹和剪裂纹产生及跨中弯曲裂纹贯通的过程,试验结束时RC板整体表现出典型的弯曲破坏特征。     

Taguchi design-based seismic reliability analysis of geostructures

This paper presents a methodology to evaluate the seismic reliability of geostructures in an optimal way. Taguchi design of experiments are adopted to find the most efficient and cost-effective combination of material properties in the uncertainty domain. Twelve uniform and mixed design models are tested. A polynomial-based response surface meta-model is built for each one and the accuracy of perdition is examined using 10,000 Monte Carlo simulations. A two-dimensional gravity dam is used as a vehicle for probabilistic transient analyses. The ground motion record-to-record variability is added as well using over one hundred earthquake records selected based on probabilistic seismic hazard analysis. Dynamic sensitivity of epistemic random variables are evaluated for the first time. Finally, an efficient and practical procedure is proposed in order to determine the reliability index of the geostructures. This approach, in fact, can be generalised for any type of engineering structures dealing with multi-hazard problems.     

Risk Analysis of Breakwater Caisson Under Wave Attack Using Load Surface Approximation

A new load surface based approach to the reliability analysis of caisson-type breakwater is proposed. Uncertainties of the horizontal and vertical wave loads acting on breakwater are considered by using the so-called load surfaces, which can be estimated as functions of wave height, water level, and so on. Then, the first-order reliability method（FORM） can be applied to determine the probability of failure under the wave action. In this way, the reliability analysis of breakwaters with uncertainties both in wave height and in water level is possible. Moreover, the uncertainty in wave breaking can be taken into account by considering a random variable for wave height ratio which relates the significant wave height to the maximum wave height. The proposed approach is applied numerically to the reliability analysis of caisson breakwater under wave attack that may undergo partial or full wave breaking.     

The dimensions of sand ripples in full-scale oscillatory flows

New large-scale experiments have been carried out in two oscillatory flow tunnels to study ripple regime sand suspension and net sand transport processes in full-scale oscillatory flows. The paper focuses on ripple dimensions and the new data are combined with existing data to make a large dataset of ripple heights and lengths for flows with field-scale amplitudes and periods. A feature of the new experiments is a focus on the effect of flow irregularity. The combined dataset is analysed to examine the range of hydraulic conditions under which oscillatory flow ripples occur, to examine the effects of flow irregularity and ripple three-dimensionality on ripple dimensions and to test and improve existing methods for predicting ripple dimensions.The following are the main conclusions. (1) The highest velocities in a flow time-series play an important role in determining the type of bedform occurring in oscillatory flow. Bedform regime is well characterised by mobility number based on maximum velocity in the case of regular flow and based on the mean of the highest one tenth peak velocities in the case of irregular flow. (2) For field-scale flows, sand size is the primary factor determining whether equilibrium ripples will be 2D or 3D. 2D ripples occur when the sand D₅₀ ≥ 0.30 mm and 3D ripples occur when D₅₀ ≤ 0.22 mm (except when the flow orbital diameter is low). (3) Ripple type (2D or 3D) is the same for regular and irregular flows and ripple dimensions produced by equivalent regular and irregular flows follow a similar functional dependence on mobility number, with mobility number based on maximum velocity in the case of regular flow and based on the mean of the highest one tenth velocities in the case of irregular flow. For much of the ripple regime, ripple dimensions have weak dependency on mobility number and ripple dimensions are similar for regular and irregular flows with the same flow orbital amplitude. However, differences in ripples produced by equivalent regular and irregular flows become significant at the high mobility end of the ripple regime. (4) Ripple dimensions predicted using the Wiberg and Harris formulae are in poor agreement with measured ripple dimensions from the large-scale experiments. Predictions based on the Mogridge et al. and the Nielsen formulae show better overall agreement with the data but also show systematic differences in cases of 3D ripples and ripples generated by irregular flows. (5) Based on the combined large-scale data, modifications to the Nielsen ripple dimension equations are proposed for the heights and lengths of 2D ripples. The same equations apply to regular and irregular flows, but with mobility number appropriately defined. 3D ripples are generally smaller than 2D ripples and estimates of 3D ripple height and length may be obtained by applying multipliers of 0.55 and 0.73 respectively to the 2D formulae. The proposed modified Nielsen formulae provide an improved fit to the large-scale data, accounting for flow irregularity and ripple three-dimensionality.     

软粘土中插入式大直径薄壁圆筒结构的一种极限状态分析模型

根据插入式大直径薄壁圆筒结构的工作特点建立了其合理的破坏机制，以此为基础建立了受横向荷载作用的插入式大直径薄壁圆筒结构的上限法极限分析模型，从中可以得到作用于插入式大直径薄壁圆筒结构上的横向极限荷载近似的上限解；并根据上限法模型计算结果，提出了计算受横向荷载作用的插入式大圆筒结构侧壁极限抗力的简化修正模型，利用此修正模型，基于极限平衡法，可以求解作用于插入式大直径薄壁圆筒结构上的横向极限荷载。     

A moving PIV system for ship model test in a towing tank

A moving particle image velocimetry (PIV) system was successfully developed and used in a large towing tank for ship model tests to observe velocity fields near ship models. The experimental method involved adjustable optical devices for various test conditions and a special particle-seeding device. The streamwise and cross-streamwise flow fields of a yacht model and a tanker model were measured. Ship type, bottom shape, and towing speed were found to be the causes of problems affecting optical access and image quality. Possible solutions, deeper optical ducts, dark painting color, and pre-processed analysis method, were proposed and discussed.     

Failure Pressure Analysis of Corroded Moderate-to-High Strength Pipelines

Based on the elastic-plastic, large-deformation finite element method, burst capacity of steel pipeline with longitudinal corrosion defect subjected to internal pressure is studied. The appropriate stress-based criterion is used to predict the failure pressure of finite element model of corroded pipeline under internal pressure. By considering the pipe steel grades and geometries of corrosion defects, a series of finite element analyses is conducted. The effects of corrosion depth, length and width on burst capacity are also discussed. A specific failure pressure solution for the assessment of corrosion defects in moderate-to-high strength pipeline is proposed on the base of numerical results. The failure pressures predicted by the proposed method are in better agreement with the experimental results than the results by the other methods.