Imaging a 3D geological structure from HEM, airborne magnetic and ground ERT data in Kalat-e-Reshm area, Iran

A set of geophysical data collected in an area in Iran are analyzed to check the validity of a geological map that was prepared in connection to a mineral prospecting project and also to image the spatial electrical resistivity distribution. The data set includes helicopter electromagnetic (HEM), airborne magnetic and ground electrical resistivity measurement. Occam approach was used to invert the HEM data to model the resistivity using a layered earth model with fixed thicknesses. The algorithm is based on a nonlinear inverse problem in a least-squares sense.The algorithm was tested on a part of an HEM dataset acquired with a DIGHEM helicopter EM system at Kalat-e-Reshm, Semnan in Iran. The area contains a resistive porphyry andesite that is covered by Eocene sedimentary units. The results are shown as resistivity sections and maps confirming the existence of an arc like resistive structure in the survey area. The resistive andesite seems to be thicker than it is indicated in the geological maps. The results are compared with the reduced to the pole (RTP) airborne magnetic anomaly field data as well as with two ground resistivity profiles. We found reasonable correlations between the HEM 1D resistivity models and 2D models from electrical resistivity tomography (ERT) inversions. A 3D visualization of the 1D models along all flight lines provided a useful tool for the study of spatial variations of the resistivity structure in the investigation area.     

Slingram EMI prospection: Are vertical orientated devices a suitable solution in archaeological and pedological prospection?

Electromagnetic induction (EMI) is one of the geophysical techniques widely used in soil studies, the slingram devices being held horizontally over the soil surface, i.e. with the coils located at the same height above the ground surface. Our study aims assessing the abilities of slingram devices when held vertically. 1D and 3D modelling have been achieved in order to compare the theoretical responses of vertical devices to the horizontal ones. Some comparative surveys were also undertaken in archaeological contexts to confirm the reliability of theoretical conclusions. Both approaches show that vertical slingram devices are suitable for survey and can constitute an alternative to the usual horizontal orientation. We give a table in Appendix A which contains the calibration coefficient allowing transforming of the values given by some of commercially available devices which would be advantageous to use in vertical orientation     

Evaluation of the reservoir permeability of anthracite coals by geophysical logging data

Permeability is one of the most significant reservoir parameters. It is commonly obtained by experiment, history simulation, injection/falloff well test and geophysical logging. Among these, geophysical logging remains as the most economic and efficient technique in evaluating coal permeability in the vicinity of an open-hole. In this paper, geophysical logging data are used to evaluate the coal reservoir permeability for the No. 3 coal seam in the southern Qinshui Basin (Fanzhuang and Zhengzhuang coal zones). Ideally coal reservoirs consist of coal matrix and fracture networks that can be represented by a model called a collection of sheets. Based on the model, coal reservoir permeability can be quantitatively calculated using the theoretical formula of k_f = 8.50 × 10^− 4 w²φ_f, in which fracture width (w) and fracture porosity (φ_f) were obtained by dual laterolog and density logging data, respectively. Calculative results show that coal reservoir permeability ranged from 0.017 mD to 0.617 mD for the Fanzhuang coal zone and from 0.047 mD to 1.337 mD for the Zhengzhuang coal zone. The permeability decreases with coal burial depth, reflecting variations in penetration capability of coal reservoirs at varying depths. Comparing results with those from injection/falloff well tests, however, shows that the model-calculated permeability is slightly higher. This is expected because the model did not include the influence from coal anisotropy.     

Sensitivity and inversion of marine electromagnetic data in a vertically anisotropic stratified earth

The controlled‐source electromagnetic (CSEM) and magnetotelluric method (MT) are two techniques that can be jointly used to explore the resistivity structure of the earth. Such methods have, in recent years, been applied in marine environments to the exploration and appraisal of hydrocarbons. In many situations the electric properties of the earth are anisotropic, with differences between resistivity in the vertical direction typically much higher than those in the horizontal direction. In cases such as this, the two modes of the time‐harmonic electromagnetic field are altered in different ways, implying that the sensitivity to the earth resistivity may vary significantly from one particular resistivity component (scalar, horizontal or vertical) to another, depending on the measurement configuration (range, azimuth, frequency or water depth). In this paper, we examine the sensitivity of the electromagnetic field to a vertically anisotropic earth for a typical set of configurations, compare inversion results of synthetic data characterizing a vertically anisotropic earth obtained using the isotropic and anisotropic assumptions and show that correctly accounting for anisotropy can prevent artefacts in inversion results.     

A radio magnetotelluric study to evaluate the extents of a limestone quarry in Estonia

Electromagnetic signals from distant radio transmitters in the frequency range 15–250 kHz were measured to model an electrical resistivity structure beneath 7 profiles in the vicinity of the Karinu limestone quarry in Estonia with the aim to map the extent of the economically exploitable limestone. The resistivity models from a 2D inversion of determinant resistivity and phase values using an Occam type of regularization contained reasonably accurate information about the geometry, namely depth to the top and the bottom of the target high‐resistivity limestone. The resistivity models correlated well with existing geological evidences as well as information from closely located boreholes. However, the sharp lithological boundaries seen in the boreholes were not resolved exactly in the resistivity models. This is probably because of the smoothing regularization used in the inversion process. Combined use of borehole data together with resistivity models resulted in two major geological interpretations; a) towards the western part of the existing limestone quarry there is a NNW to NS striking fault, covered by post‐glacial sediments, b) a potential cost‐effective exploitable area containing high quality highly resistive limestone is located south of the existing quarry. This case study shows the applicability of the reasonably fast radio magnetotelluric (RMT) method for the exploration of near‐surface resources.     

油田压裂井地电法双参数联合监测技术与仪器研究

目前世界上水力压裂技术是老油田增产和低渗透油气田开发所应用最为广泛、最为有效的技术措施,油气储层裂缝分布规律监测对于油田勘探开发具有重要意义.本文利用压裂液在地层中的低阻特性与极化特性,基于井地电阻率法与激发极化法联合,根据位场理论镜像原理,采用三维有限差分,计算了多种压裂模型的地表传导电位与极化电位;通过非等权值的数据融合算法,计算了地表双参数异常,仿真数据的研究结果表明,双参数融合技术在异常提取方面具有明显优势.在此基础上,基于双波大功率联合发射技术、时分复用低噪声接收技术,研制了井地电法双参数联合监测仪器系统,共模抑制比达110 dB,有效地提取了微弱异常信号.通过陕西省富县华北局油田的压裂野外联合监测试验,表明了井地电法双参数联合监测仪器系统在水力压裂裂缝监测中具有较好的监测效果和较高的分辨率,解决了在低电阻率储层压裂或深井压裂情况下监测困难以及单一方法的监测结果多解性等问题,实现对油田水力压裂裂缝的实时监测.     

Examples of geomorphologic and geological hazards in Algeria

We present three geomorphologic and geological phenomena that have occurred in Algeria in recent years: (i) the Bab El Oued mudflow on 11 November 2001, which claimed several hundred lives, (ii) a soil collapse induced by sand liquefaction triggered by the Boumerdes earthquake (M _w = 6.8) on 21 May 2003, and (iii) landslides that are threatening Constantine city, for which a hazard map is presented using a qualitative approach. We briefly describe and analyze these natural disasters, and in the first two cases propose the application of geophysical techniques such as ambient noise recordings and electrical imagery to help evaluate their extent and potential threat. Finally a landslide hazard map of Constantine is proposed.     

Assessing aquifer vulnerability to pollutants by electrical resistivity tomography (ERT) at a nitrate vulnerable zone in NE Spain

There is an increasing demand for groundwater vulnerability maps which illustrate the exposure of aquifers against pollution. These maps show areas of greatest potential for groundwater contamination on the basis of local subsurface conditions. Parameters affecting vulnerability are mainly permeability and thickness of each protective layer. For unconsolidated sediments, the permeability is strongly related to the clay content, which can be deduced from indirect resistivity methods, like electrical-imaging. Such geophysical methods can be of great help in groundwater vulnerability studies because they disturb neither the structure nor the dynamics of the soil. Sensibility analysis was performed of the electrical resistivity tomography method for accurately mapping soil media. Managers and public administrators may effectively use this method for assessing the potential risk of groundwater contamination. In the studied zone, electrical resistivity exhibits a wide range of variability that can be easily correlated to soil parameters, such as clay content and hydraulic conductivity. A numerical index of protection has been assessed from the geophysical information derived from 2D electrical resistivity tomography. This work represents a preliminary approach on the natural vulnerability evaluation of shallow aquifers at the Empordà basin (NE Spain) that is highly affected by diffuse pollution by nitrates.